• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.1
• /
• pp.45-54
• /
• 2012

Optimization of the asymmetric trapezoidal fin with various upper lateral surface slope is made using a two-dimensional analytic method. For the fixed fin base height, the optimum heat loss, fin length and effectiveness are represented as inner fluid convection characteristic number, fin base thickness, fin base height, fin shape factor and ambient convection characteristic number. For this optimum procedure, the optimum heat loss is defined as 95% of the maximum heat loss from the fin. One of the results shows that optimum heat loss and effectiveness seems independent of the fin shape factor while optimum fin length decreases almost linearly as the fin shape factor increases.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.60-67
• /
• 2013

Test cost reduction is necessary to test a complex System-on-a-Chip(SoC) which adopts various Intellectual Properties (IP). In this paper, test architecture with low pin count which is able to IP-based SoC test, using IEEE Std. 1149.7 and IEEE Std. 1500, is proposed. IEEE Std. 1500 provides independent access mechanism for each IP in IP-based SoC test. In this paper, just two test pins are required by composing that these independent access mechanism can be controlled by IEEE Std. 1149.7. The number of Chips which are tested at the same time is increased by reducing required test pin count at wafer and package level test, and consequently the overall manufacturing test cost will be reduced significantly.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.274-280
• /
• 2005

The objective of this study Is to investigate the heat transfer performance of plate discrete fin-and-tube heat exchangers with large fin pitch. In this study, twenty-two heat exchangers were tested with a variation of fin pitch, number of tube row, longitudinal tube pitch and fin alignment. Discrete fin type exchangers improved heat transfer performance more than 10% compared to tile continuous fin type heat exchangers. The air-side heat transfer coefficient decreased with a reduction of the fin pitch and an increase of the number of tube row, The staggered fin alignment improved heat transfer performance more than 6% compared to the inline fin alignment. The effect of longitudinal tube pitch was insignificant on the j-factor and experiments found opposite effects on the j-factor with respect to fin alignment. Heat transfer correlations were developed from the measured data for flat plate discrete fin-and-tube heat exchangers with large fin pitch. The correlations yielded good predictions of the measured data with mean deviations of 1,4% and 0.3% for tire inline and staggered tube alignment, respectively.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.2
• /
• pp.63-69
• /
• 1999

The frequency-dependent characteristics of the finline have previously been analyzed using several frequency domain approaches. But the time domain TLM method presented in this paper is another independent approaches for obtaining frequency domain results for finline. The structure analysed with this algorithm is unilateral finline in WR-62 waveguide enclosures and the symmetrical condensed node based on the properties of Huygen's scattering model is used. From the TLM results, the frequency-dependent scattering parameters of a unilateral finline have been calculated by Fourier transform of the time domain data. The numerical results are in good agreements with other paper, thus demonstrating the validity and usefulness of the proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.570-582
• /
• 2012

In the communication, a reconfigurable antenna using two PIN diodes is presented for quad-band(GSM900/GSM1800/GSM1900/UMTS) mobile handset applications. The proposed antenna has a size $45{\times}11{\times}6mm^3$. By independently adjusting the on/off states of two PIN diodes located on the radiating element, the proposed structure can be operated in the PIFA and loop mode, respectively. The PIN diodes are replaced by conducting tape in order to verify the concept. In regards to the fabricated reconfigurable antenna, when operating in the PIFA mode, the measured results show that the 7 dB bandwidth is 8.62 %. which covers the GSM900(880~960 MHz) band. When operating in the loop mode, the measured results show that the 7 dB bandwidth is 26.36 %, which covers the GSM1800(1,710~1,880 MHz), GSM1900(1,850~1,990 MHz), and UMTS(1,920~2,170 MHz) bands, respectively.

• Composites Research
• /
• v.23 no.3
• /
• pp.1-6
• /
• 2010

Recently, CFRP composite is more and more used in the various fields because of a higher specific modulus, chemical property and so on. Most products using CFRP composite are manufactured by construction of components. Various components are joined with those by bolts and pins. Holes for bolts and pins decrease strength and fatigue life of components, because those act as notch in structures. In this paper, we experimentally evaluated the fatigue life of hole-notched and unnotched weave CFRP plate. Then, we compared the two results and proposed an equation for prediction of fatigue life.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.463-466
• /
• 2006

최근 전자기기에서 시각 및 청각과 함께 촉각 디스플레이가 정보를 출력하는 중요한 수단으로 부각되고 있다. 본 논문에서는 촉각 정보 출력을 위한 소형진동촉각(vibrotactile) 디스플레이 모듈을 개발하였다. 개발한 모듈은 주파수와 진폭을 독립적으로 조절할 수 있으며 핀이 직접 피부에 자극을 주기 때문에 몸체 전체가 떨리는 기존의 진동모터보다 정밀하고 다양한 촉각 표현을 할 수 있다. 또한 고전압을 이용하는 Piezo 방식과 달리 낮은 전력으로 동작이 가능하여 휴대장치에 직접 장착할 수 있는 장점을 가지고 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.660-664
• /
• 1997

본 논문은 사출금형 설계를 위한 전문가 시스템의 개발에 관한 연구이다. 설계자가 오토케드 (AutoCAD)환경에서 금형부품 및 몰드베이스를 3차원 형상으로 나타낼 수 있으며 필요한 설계 데이터를 추가할수 있는 프로그램 개발에 있다. 주 프로그램은 C++를 사용하여 구축하였으며,금형부품 치수 및 몰 드베이스를 데이터베이스화 하였다. 주 프로그램과 오토캐드와 인터페이스를 하여 오토캐드 환경에서 자 유롭게 사용할 수 있도록 하였다. Pull-down menu와 Dialog box를 이용하여 금형 설계자가 금형의 각 부 품을 자유롭게 선정할 수 있으며, 각 단계별 선정된 금형부품은 즉시 나타나 설계자가 바로 확인 할 수 있도록 하였다. 이젝터 핀의 위치 및 크기를 자동적으로 나타낼수 있으며, 선정된 금형 부품 및 몰드베이 스는 2차원이나 3차원으로 나타낼 수 있다. 각각의 3차원 부품을 독립적으로 나타낼 수 있어 NC프로그램과 인터페이스가 가능토록 하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.481-486
• /
• 2010

Recently, carbon fiber reinforced plastic (CFRP) have been used in various fields because of its high specific modulus, and chemical properties. Most products in which CFRP composites are used are manufactured by joining the product components by bolts or pins. Holes for bolts and pins decrease the strength of the components because these holes act as notches in the structures. In this study, the fracture strength of CFRP plain-weave composite plates containing holes is experimentally investigated to examine the effects of hole-size and specimen width on notched tensile strength. The results show that the characteristic length considered in the point stress criterion depends on the hole size and specimen width. There exists a certain relation between notched tensile strength and characteristic length. Fracture criterion is redefined on basis of this relation.

• The Journal of Natural Sciences
• /
• v.14 no.1
• /
• pp.25-37
• /
• 2004

T7 RNA polymerase also recognize intrinsic, hairpin-independent termination signal, a conserved 7-base pair sequence (ATCTGTT in the non-template stand) and U-rich sequence downstream of it. These intrinsic, hairpin-independent termination signal were commonly found in PTH and CJ termination sequences. There are two types of mutant T7 RNA polymerases recognizing sensitively(X3, X19, BG8) of insensitively (R173C) the intrinsic termination signals. We determined the T7 transcription activities of these mutants. Compared to wild-type, mutants X4, 19 and BG8 show highly reduced transcription activities (8%, 33%, 34%). On the other hand mutant R173C shows comparable transcription activity of wild-type (112%). Also transcription termination efficiencies at the PTH or CJ termination signals were determined by using mutant RNA polymerases. Temination of mutnats X4, X19 and BG8 are increased compared to wild-type. On the other hadn mutant R173C proceeds through PTH and CJ termination signals.