• Journal of radiological science and technology
• /
• v.38 no.1
• /
• pp.7-15
• /
• 2015

A ultrasonic probe is very important in medical ultrasonic image, but the frequency of probe defects are often. Therefore practical tools for probe based ultrasonic QA should be developed. Advanced research on the effects of the probe defects on the quality of ultrasonic images is required. This study has investigated the effects of the defects in the probe elements influence Doppler images in the medical ultrasonic scanners. Especially the defects in a set of adjacent elements(SAE) electrically disconnected influence Doppler images were tested. The results show Doppler brightness and velocity became rapidly reduced as the defected elements is located centrally, as the defected elements is activated. The more the defected elements increased, the more Doppler brightness and velocity increased. As a set of the element disconnected moved, it appeared Doppler velocity starting to decrease and then was followed by brightness. The strength is not consistent with the velocity in the number and location of the defected elements. The defects in the probe elements influence Doppler velocity when the defected elements got out of the elements activated at Doppler mode.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.142-150
• /
• 2019

Muzzle Velocity is one of the most important measurement items for evaluation of ammunition. The muzzle velocity is defined as the velocity when the projectile leaves the muzzle. Particularly, since the muzzle velocity is closely related to the performance of the propellant, precise measurement of muzzle velocity is required. Doppler radar is used to measure the muzzle velocity, but the quality of Doppler radar signal depends on the test site environment. In this paper, a method to remove the clutter that degrades the signal quality of Doppler radar by improving the structure of the test site and the signal processing method is suggested. For the application of the improved signal processing method, a program for acquiring Doppler radar's raw Doppler data was created. Statistical verification of the velocity data obtained through the improvement of the test site structure and signal processing method proved that the proposed method is effective for the removal of clutter as compared with the existing method.

• Publications of The Korean Astronomical Society
• /
• v.6 no.1
• /
• pp.16-26
• /
• 1991

스펙트럼선의 선폭증대 현상을 방출영역 내 기체입자들이 열운동에 의한 단순 도플러 효과로 가정하여 중심에서 어느 한쪽으로 심하게 치우친 스펙트럼 선윤곽를 해석한다. 본 연구에서는 태양활동영역에서 흔히 관측되는 좌우 비대칭의 선윤곽을 서로 다른 가우스속도분포의 기체성분들이 시선방향으로 중첩된 결과라 해석하고, 최소자승법을 이용한 비선형 선윤곽 맞춤질에 의해 스펙트럼 방출영역에서 떨어져 나가는 기채들의 온도 및 분출속도에 관련된 도플러선폭과 도플러이동량을 구하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.7
• /
• pp.685-691
• /
• 2011

The aim of this study is to point out the uniqueness of Doppler optical coherence tomography (DOCT) for use in a probe station for (in vivo) visualization of microscale flow and structure and to maximize the effectiveness of DOCT by overcoming its limitations. Conventional DOCT produces images of only one of the velocity components that is parallel to the incident light. In this study, a multi-angle DOCT to quantify a velocity vector field is proposed; this is an extension from a velocity scalar field to a vector field. Quantifying an instantaneous three-dimensional velocity field in a pulsating flow is another challenge because of its limited frame rate. The in-vivo pulsating blood flow is measured by using an electrocardiogram-gated multi-angle DOCT in a hamster cheek pouch model. It is shown that the aliasing problem caused by a relatively low frame rate is resolved by using this method of measurement.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.516-519
• /
• 2001

To diagnose a patient's blood vessel disease, apoplexy, hypertension, arteriosclerosis, the blood velocity is very important. Determining the blood velocity methods using ultrasound are Continuous Doppler System and Pulse Doppler System. In using the Pulse Doppler System, we can obtain the position of blood velocity. But it is more complex hardware than Continuous Doppler System and it has low SNR(signal-noise ratio). So in this study, to obtain a believable information we use the Continuous Pulse Doppler System. Thus system have analog part and digital part. In analog part is composed of ultrasound generating part, the amplifying part to amplify the received signal from ultrasound sensor, the demodulation part to detect blood velocity and the filtering part to remove the noise. In digital part is composed of the A/D conversion part, digital signal processing part, and the communication part to communicate the PC. In this study to implement efficient ultrasound blood velocity measurement system, we can get the patient's blood velocity information in realtime. Thus, It is a useful in the accurate diagnosis with C.T(computered tomography), M.R.I(magnetic resonance imaging).

• Korean Journal of Remote Sensing
• /
• v.29 no.1
• /
• pp.11-20
• /
• 2013

Space-borne Synthetic Aperture Radar(SAR) has been one of the most effective tools for monitoring quantitative oceanographic physical parameters. The Doppler information recorded in single-channel SAR raw data can be useful in estimating moving velocity of water mass in ocean. The Doppler shift is caused by the relative motion between SAR sensor and the water mass of ocean surface. Thus, the moving velocity can be extracted by measuring the Doppler anomaly between extracted Doppler centroid and predicted Doppler centroid. The predicted Doppler centroid, defined as the Doppler centroid assuming that the target is not moving, is calculated based on the geometric parameters of a satellite, such as the satellite's orbit, look angle, and attitude with regard to the rotating Earth. While the estimated Doppler shift, corresponding to the actual Doppler centroid in the situation of real SAR data acquisition, can be extracted directly from raw SAR signal data, which usually calculated by applying the Average Cross Correlation Coefficient(ACCC). The moving velocity was further refined to obtain ocean surface current by subtracting the phase velocity of Bragg-resonant capillary waves. These methods were applied to Envisat ASAR raw data acquired in the East Sea, and the extracted ocean surface currents were compared with the current measured by HF-radar.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.250-254
• /
• 2000

We have constructed laser Doppler velocimetry system using self-mixing effect with a semiconductor laser. This technology is based on the frequency mixing phenomena which occurs when light scattered back from the moving object into the laser cavity interferes with light inside the laser. We have compared the value of Doppler shifted frequency with the velocity variation of the wheel. Frequency dependence on the angle between the moving direction of rotating aluminum wheel and the incident beam also have been proved. As an illustration of the performance of the velocimeter, velocity measurements of a rotating disk are described. Doppler signal shows a good linear relationship with velocity of rotating disk.

• Journal of radiological science and technology
• /
• v.38 no.4
• /
• pp.443-449
• /
• 2015

An ultrasound probe has a big impact on Doppler images even though it has very high risk of frequent function-breakdowns occurring in medical ultrasound scanners. This study experimentally analyses the impacts of an ultrasonic probe's defected elements on power & color Doppler images. The results show that, the bigger the size of defected probe elements is, and the closer a group of action elements is to the center, the more the brightness of images and the velocity of Doppler diminish. When elements' defects increase in color & power Doppler images, false images are formed to be mistaken for blood-vessel plaque in neighboring regions. Accordingly, whenever element defects are suspected, we need check-up process in B-mode. From this respective, it is advisable to have primary interest in a probe and carry out continuous probe QA for ultrasonography.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.114-125
• /
• 2014

In a conventional sonar system, which uses LFM signal for detecting targets with varying speed, the results of multiple LFM Doppler correlators are aligned and the maximum alined result are selected as a test cell for detecting targets. As the number of the LFM Doppler correlators are increased for accurate target detection, as the required computational complexity and the memory are also increased. This fact makes it difficult to implement the accurate LFM target detector. In this paper, we propose a new fast target detection which is robust for the variation of target speed. Because the proposed method uses the summation of alined results of large numbers of LFM Doppler correlators, the proposed method increase SNR and provide robust SNR for the variation of target speed. And the proposed method can provide very fast target detection by implementing the process, the summation of alined results of large numbers of LFM Doppler correlators, as one summation filter.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.377-380
• /
• 2000

도플러 로그용 센서를 이용하여 선박의 속도를 측정하면, 선박의 수평방향 이외의 움직임, 즉 핏칭이나 롤링 등에 의한 측정 속도의 부정확성이 문제가 된다. 본 연구에서는 이러한 핏칭과, 수중이라는 환경요인에 기인하여 다른 속도 측정용 센서들이 가지는 문제점을 극복할 수 있도록 진동판을 수평축에서 일정한 각을 가지도록 두 개 또는 네 개를 등 간격으로 배열한 야누스형 초음파 트랜스듀서를 개발하였다. 트랜스듀서 개발을 위하여 그 작동 구조를 해석하고 그에 따라 시제품을 제작한 후, 실험적인 성능 평가를 수행하였다. 시제작된 초음파 트랜스듀서는 지향성 및 감도가 우수하고, 대역폭이 넓은 성능을 가지고 있어, 실제 선박에 장착되어 도플러 로그용 초음파 트랜스듀서로 사용될 수 있는 가능성이 확인되었다.