• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.545-554
• /
• 2003

Design of the optical modulator composed of a three-waveguide coupler and CPW traveling-wave electrodes was carried out. Switching phenomena of three-waveguide couplers were analyzed by using the coupled mode theory, and the coupling-lengths of the devices were calculated by means of the FDM. CPW traveling-wave electrodes were analysed by the CMM and SOR simulation technique in order to find the conditions of phase-velocity and impedance matching. Traveling-wave modulators were fabricated on z-cut LiNbO$_3$ substrate. Ti was in-diffused in LiNbO$_3$ to make waveguides and Au electrodes were built on the waveguides by the electrolyte technique. The fabricated modulator chip was end-polished, pig-tailed and packaged in a brass mount with K-connector. The insertion loss and the switching voltage of the optical modulator were about 4㏈ and 19V, respectively. Network analyzer was used to obtain the S parameter and the corresponding RF response. From the measurement, parameters of the traveling-wave electrodes were extracted to be Z$_{c}$= 45 Ω, N$_{eff}$=2.20, and $\alpha$$_{0}$=0.055/cm√GHZ. The measured optical response R($\omega$) was compared with the theoretically estimated one, showing both responses agree well. The measurement results revealed that 3㏈ bandwidth turned out to be about 13 GHz.

• Korean Journal of Optics and Photonics
• /
• v.20 no.2
• /
• pp.128-133
• /
• 2009

In this paper, an optical touch panel device is newly proposed, with operating principle based on the optical coupling between a pointing pen having a built-in light source and perpendicularly crossed optical waveguide arrays. In order to enable an external light to couple into a waveguide core, the auxiliary pyramidal structures are introduced into all intersecting points located periodically along optical waveguides. The shape is optimized for minimizing the unwanted propagation loss due to the same structure by a ray tracing method. For the optical waveguide with the size of $50{\times}50{\mu}m^2$, the bottom width, height, and slope angle of the optimized pyramidal structure are $50{\mu}m$, $22.5{\mu}m$, and $42^{\circ}$, respectively. The optical coupling efficiency of about 97.8% and the average propagation loss of 0.3 dB/mm were achieved for the optimized touch panel. Finally, it is found from the tolerance analysis that tilting of the pen up to ${\pm}12^{\circ}$ can be allowed.

• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.142-145
• /
• 2003

The nonreciprocal phase shift characteristics of infinite slab optical waveguides with magneto-optic materials in the cladding layer was calculated at 1.55 ${\mu}{\textrm}{m}$ for optical isolators. The infinite slab waveguide structures considered in this paper were as follows. rho magneto-optic materials used as a cladding layer were Ce:YIG and LNB(LuNdBi)$_3$(FeAl)$_{5}$)$_{12}$,). Their specific Faraday rotations Θ$_{F}$ are 4500$^{\circ}$/cm, 500$^{\circ}$/cm at wavelength 1.55 ${\mu}{\textrm}{m}$ respectively. The guiding layer with multi-quantum well structure was used, and it consists of 1.3Q and InGaAs. In order to investigate the effect of evanescent field penetrating the cadding, layer, guiding mode characteristics were calculated for the cases when the substrate is InP and air. We calculated the minimum lengths of 90$^{\circ}$ nonreciprocal phase shifters and their optimum guiding layer thicknesses in various optical waveguide structures.res.s.

• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.241-247
• /
• 2023

We examine the spectral characteristics of laser-induced periodic surface structures (LIPSSs) formed on an amorphous silicon film irradiated by a 355-nm nanosecond laser. A Gaussian beam with a diameter of 196 ㎛ is used to perform a two-dimensional raster scan. The laser's pulse number is varied from 190 to 280, and its intensity is adjusted within 100-130 mJ/cm². LIPSSs with a periodicity of approximately 330 nm form on the surface of the Si film, aligned perpendicular to the laser's polarization. Transmission spectra of the samples show dips around 700 nm for transverse electric polarization and around 500 nm for transverse magnetic polarization. The features are investigated with a one-dimensional-grating model using a rigorous coupled-wave analysis. Simulations confirm that the observed dips are due to the resonant modes, depending on the polarization.

• Journal of the Korean Chemical Society
• /
• v.49 no.1
• /
• pp.47-55
• /
• 2005

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.221-222
• /
• 2009

이 논문에서는 기존의 FBG 광센서와는 달리 이중파장 구조를 갖는 FBG 센서를 제안하여 기 존의 FBG 센서가 측정할 수 있는 범위를 획기적 으로 증대시킴을 보이고자 한다. 고해상도의 광범 위한 지역 측정은 두 가지의 광대역 광원을 이용 하는 매트릭스 구조의 FBG를 이용해 구성하였으며, 두 광원을 사용하는 통합시스템은 도파로 열격자(AWG)로 구성되어 있다.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.147-148
• /
• 2009

We have fabricated a down tapered polymer tip on optical fiber end-face by a guided UV light. One side of fiber was aligned with a mercury-xenon lamp and another was put into UV curable polymer. A shape of tip was controlled by adjusting an irradiance of lamp and time of exposure. A bending effect also affects the result. Optical characteristic was achieved preliminarily with solution of minute particles.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.257-259
• /
• 1990

In the design of waveguide E-plane bandpass filter, it is very important to characterize the K-inverters. In the analytical method. losses arising from the metal and the dielectric are ignored for the simplicity of design process. In this paper, based on the new measurement method, characteristics of inverters are measured and compared with those calculated based on mode-matching analysis.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.192-193
• /
• 2002

지금까지 측면이 코어 가까이 연마된 잔일모드 광섬유와 평면 도파로 사이의 광결합을 이용한 소자들이 많이 연구되고 있다. 이를 이용한 소자들로는 광필터, 광변조기, 광스위치, 굴절계, 편광기 등이 있으며 최근에는 파장분할다중화(WDM)에서 인접채널간의 채널분리를 위한 소자로서 빗살필터의 연구 또한 활발히 이루어지고 있다. 이에 본 논문에서는 측면이 코어 가까이 연마된 단일모드 광섬유와 평면도파로 사이의 광결합을 이용한 빗살필터를 제작하였으며 열광학 효과를 이용하여 파장 가변 빗살 필터를 구현해 보았다. (중략)

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.190-191
• /
• 2002

광소자 설계 시 TE/TM 분극에 대한 민감도는 매우 중요한 요소로 작용을 한다. 이러한 민감도를 줄이기 위해 많은 광소자에 다중모드 간섭기가 이용되고 있다. 다중모드 간섭기에 입력되는 신호는 TE와 TM 두 모드의 분극으로 이루어져 있으며, 각각은 도파로 내에 존재하는 모드에 실려 50：50의 파워 분배를 가지고 진행하게 된다. 그러므로 광소자를 제작하기 위해 TE 또는 TM 모드만을 고려하는 것은 소자의 효율을 떨어뜨리는 요인으로 작용한다. (중략)