• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.6
• /
• pp.38-43
• /
• 1981

In this paper an actively compensatedfinite gain amplifie. (FGA) with positive gain using 4 operational amplifiers and resistors is propo sod, and an application is considered in an active RC filter. By cancelling the effect of the GB's up to the third-order term of s on the transfer function, the proposed FGA has the extended frequency range over that of the FGA using 3 operational amplifiers. When this FGA is applied to an active RC filter with Pole frequncy of 100kHz, the magnitude error of the frequency characteristics of the filter is less than 2%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.5
• /
• pp.463-470
• /
• 2015

In this paper, a new dual-band bandpass filter(BPF) that has resonators and feed lines with Stepped-Impedance Resonator(SIR) structures is proposed. Feed lines with SIR structure provide maximum magnetic field points which occur at the same locations of the input and output feed lines, so the insertion loss of BPF was reduced. Applying the SIR structure to the BPF for the first passband improves rejection characteristics between the first passband and the second passband. It reduces the coupling between the BPF for the first passband and the BPF for the second passband, so it makes the dual-band BPF more compact. The proposed design method provides independent changes of both the center frequency and the bandwidth for each resonator, and also improves filtering characteristics. The validity of the proposed design method is confirmed by comparisons between the designed parameters and the measured results satisfying WLAN specifications.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.1
• /
• pp.1-8
• /
• 1970

The band-stop filters which resonate at intervals of one-quarters, and three-quarters guide-wave length are designed and its frequency characteristics are measured. 2K25 klystrons (at 8000MC) were used as microwaves source. This bandstop filters were designed from low pass prototype and the Impedance of Impedance of these filters was made to be equal to one of the low pass prototype. It is demonstrated that the filters considered here, have narrow stop bandwidths and sharp characteristics in the stop band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.5
• /
• pp.872-882
• /
• 1994

In this paper, the Low Noise Amplifier(LNA) is designed and fabricated to include a band pass filter characteristics considering the antenna system characteristics according to the transmitting and receiving signal level of communication satellite transponder. As an example, a 2-stage low noise amplifier and a 4-stage amplifier and designed, fabricated and measured at 14,0~14.5GHz of receiving frequency band. This fabricated LNA has shown the gain with very good flatness within pass-band, and its gain decreases rapidly out of band resulting in supperssion of the transmitting signal power leakage. It has shown the 20.3dB +- 0.1dB of pass-band gain, the 1.44dB +-0.04dB of noise figure and the 14dB rejection out of band(12.25~12.75GHz). The gain flatness, noise figure and group delay of this 2-stage LNA satisfactorily met the simulation results. And the fabricated 4-stage amplifier has shown the more than 42dB of pass-band gain, the +-0.25dB of flatness and the 28dB of the rejection effect for transmitting power leakage. The 2-stage LNA and 4-stage amplifier, in this paper, will bring a design margin for the input filter and also result in the system cost reduction.

• Journal of Korea Multimedia Society
• /
• v.6 no.2
• /
• pp.352-359
• /
• 2003

In this paper, we designed the bluetooth receiver using the microstrip bandpass filter and the high gain low noise amplifier with the 0.2$\mu\textrm{m}$ CMOS technology. A cascode inverter is adopted to implement the low noise amplifier and is one stage amplifier with a voltage reference and without the choke inductor. The designed 2.4GHz LNA was achieved a power gain of 18dB, a noise figure of 2.8dB, and the power consumption of 255mW at 2.5V power supply. Also, the microstrip receiver bandpass filter was designed that the center frequency was 2.45GHz, the bandwidth was 4% and the insert attenuation was -1.9dB. When the microstrip bandpass filter and LNA was simulated together the power gain was 16.3dB.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2299-2304
• /
• 2011

In this paper, we propose the methodology to make the bandpass filters for the Smart Grid IED(Intelligent Electronic Device) smaller than the conventional bandpass filters. The size-reduction of the filters and the filter performances are indebted to devising small CRLH(composite right- and left-handed) resonators and coupling them as the metamaterial structures. The design methodology is validated by the equivalent circuit to be compared with the reliable full-wave EM simulation, and the proposed metamaterial filter outperforms the standard parallel-edge coupled filter with respect to the miniaturization and frequency response.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.371-374
• /
• 2010

In this article, new microstrip slow-wave bandpass filters using open loop resonator loaded with inter-digital capacitive fingers is proposed. The filter features not only compact in size, but also exhibits spurious stop-band rejection. Filters of this type with elliptic function and Chebyshev response are demonstrated. There is good agreement between experimental and full-wave electromagnetic (EM) simulation results.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.2
• /
• pp.83-90
• /
• 2005

In this paper, we proposed the newly design method for extracting of the saw resonator characteristic. For the parameters of the proposed equivalent model, we adjusted and optimized the variables of several functions. As verification of proposed method, we firstly designed and fabricated cellular saw resonator by using the proposed model resonator. As the simulated and measured results of the proposed design method are almost equaled, we confirmed the usefulness of this method. we knew the usefulness of this method. Finally we designed the 800MHz cellular Tx/Rx band pass filter by using this designed resonator.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.11
• /
• pp.70-77
• /
• 1996

In this paper, a modifed TE$_{113}$/TM$_{012}$ triple-mode bandpass filter is implemented by using a modified inter-cavity iris in which the number of slots are reduced upto 50%. In a coventioanl iris two prirs of slot apertures are used to independently couple three resonant modes between two adjacent cavities. However, if transverse magnetic polarizability of a pair of veritcal slot apertures is used to control weak horizontal TE$_{h}$-TE$_{h}$ mode coupling, the width of novel iris slots would substitute for the slot length of the conventional iris, causing to eliminate the horizontal slot apertures. The measured data of two filters, which are the modified filter and ocnventional one, are compared. Experimental result shows that the characteristics of the novel triple-mode filter matches well that of the conventional filter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.6
• /
• pp.521-527
• /
• 2002

In this paper, we introduce a procedure to find design parameter for array coupled lines using 2-D finite element analysis. To extract design parameters using FE calculation, we set up several design conditions. In order to show the validity of our approach, we designed, simulated and fabricated a comb-line bandpass filter.