• Analytical Science and Technology
• /
• v.9 no.2
• /
• pp.179-191
• /
• 1996

In order to understand the high temperature deformation behavior of superalloy 718, a rotating grade 718 alloy has been compression tested to about 0.7 upset ratio at $927{\sim}1066^{\circ}C$ temperature range and $5{\times}10^{-4}{\sim}5{\times}10^0sec^{-1}$ strain rate. The maximum flow stress was increased with increasing strain rate, and similar behavior was observed with decreasing temperature. At low temperature and high strain rates other than $5{\times}10^{-1}sec^{-1}$, strain softening was occurred mainly by dynamic recovery and deformation twinning processes, while at high temperature and low strain rates strain softening was offseted by dynamic recrystallization. At $5{\times}10^{-1}sec^{-1}$, strain hardening was occurred due to work hardening of the dynamic recrystallized grains. Strain rate sensitivity, m, was varied with strain rates. In the case of lower strain rate tests, m was measured as 0.3 and it was observed that the deformation was mainly controlled by dynamic recrystallization. At higher strain rate, m was lowered to 0.1 and the deformation was controlled by the dynamic recovery and the deformation twinning processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.481-492
• /
• 2018

The steel-plate concrete composite beam is composed of a steel plate, concrete and shear connector to combine two inhomogeneous materials. In general, the steel plate is assembled by welding an existing composite beam. In this study, the SPC beam was composed of folding steel plates and concrete, without a headed stud. The folding steel plate was assembled by a high strength bolt instead of welding. To improve the workability in a field construction, a hat-shaped cap was attached to the junction with a slab. Monotonic load testing under two points was conducted under displacement control mode to analyze the flexural strength of the SPC beam using a cap as the shear connector. Five specimens with shear connector types, protrusion length, and different thickness of steel plates were constructed and tested. The experimental results were analyzed through the relationship between the shear strength ratio and flexural strength in KBC 2009. The test results showed a shear strength ratio of more than 40 %. In the case of using a cap-like specimen as the shear connector, the flexural strength was 70% of the value calculated as a fully composite beam. In addition, the cap showed a smaller shear strength than the stud, but the cap served as a shear connection. When the thickness of the steel plate was taken as a variable, the steel plate exhibited a bending strength of approximately 70% compared to a fully formed steel plate, and exhibited similar deformation performance. Local buckling occurred due to incomplete composite behavior, but local buckling occurred at a 5% higher strength for a relatively thick steel plate. The buckling width also decreased by 15%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.47-53
• /
• 2020

The purpose of this study was to increase product reliability by improving the durability of the breech block for a 30mm Automatic Gun. The breech block is a key component of a gun that functions as chambering, closing, and extracting. The breech block requires high reliability, which needs to be improved because cracks of a breech block can occur early in operation. Cause analysis confirmed that the crack is caused by repeated impacts. Therefore, the following improvement measures were studied, and the effects were demonstrated using a firing test. The energy of impact absorption was increased by changing the material, and the stress concentration was mitigated by increasing the value of R. In addition, the fatigue life was increased by adding Shot-peening, deleting chromium plating, and changing the forging method. The firing test did not show firing trouble for up to 5,000 rounds. The start timing of the crack was delayed, and the depth was small. Therefore, the improved product was more durable than the existing product. This study can be used as a useful reference when assessing the improvement of the durability of similar products, life study, and criteria for crack acceptance.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.411-419
• /
• 2003

This paper aims at developing 'gyro-mouse' which provides decent and comfortable human-computer interface that supports the usage of such software as an internet-browser in PC for the people paralyzed in upper limbs. This interface operates on information collected from head movement to get the cursor control. The interface is composed of two modules. One is hardware module in which the head horizontal and vertical angular velocities are detected and transmitted into PC. The other is a PC software that translates the received data into movement and click signals of the mouse. The ANN (artificial neural network) learns the quick nodding pattern of each user as click input so that it can provide user-friendly interface. The performance of the system was evaluated by three indices that are click recognition rate. error in cursor position control. and click rate of the moving target box. The performance result of the gyro-mouse was compared with that of the optical-mouse to assess the efficiency of the gyro-mouse. The average click recognition rate was 93%, average error in cursor position control was 1.4∼5 times of optical mouse. and the click rate with 50 pixels target box was 40%(30 clicks/min) to that of optical mouse. The click rate increased monotonously with the number of trial from 35% to 44%. The suggested system is expected to provide a new possibility to communicate with the society.

• Journal of Korea Technology Innovation Society
• /
• v.19 no.4
• /
• pp.711-735
• /
• 2016

Drug Development is very important for promoting public health and pharmaceutical industry. There has been many studies on the efficiency of drug development, but there are few studies on the drug development R&D performed by government. Since CCR model assumes unidirectional influence of input and output, it is not appropriate to analyze the efficiency of R&D due to the time-lag and spill-over effect. Also, BBC model which assumes variable returns to scale has difficulty in deriving priorities between decision making units. Recently, Range Adjusted Measure (RAM) model has been suggested in R&D efficiency analysis. RAM model measures the efficincy by eliminating inefficiencies under variable returns to scale assumption, and its strong monotonicity enables to provide clear priorities between decision making units. In this study, we analyzed the efficiency of national R&D programs for drug development using the two-step approach, including RAM model and Tobit regression analysis, and discussed major policy implications.

• Conservation Science in Museum
• /
• v.2
• /
• pp.57-68
• /
• 2000

This study is a scientific analysis of 12 bronze materials which were excavated from Sanoisa temple in Chongju. Analysis of crystalline shape, size and distribution of the each sample metal suggested that they can be classified as tableware(wrought), vessels for memorial service(casting) and bell bronze, which is the same result as classification based on elemental composition. Most of the tableware are forging wares with composition of 8:2:0 in Cu:Sn:Pb, and vessels for memorial service are casting wares whose composition is 7:1:2 in Cu:Sn:Pb, and bell bronze's composition is Cu:Sn:Pb = 85:10:5/9:1:0. The result clearly shows that composition is closely related with usage and manufacturing method of wares. Trace elements such as Co, Fe and As are the elements with high correlation coefficient with Cu, which means they exist as impurities in Cu, and the content of As showed an increase in the order of tableware, memorial service vessels and bell bronze. In addition, the analysis of lead isotope ratio showed that 3 bronze materials with high lead content were made from the lead coming from Japan and China. The composition of the solder was Cu:Sn:Pb = 83:12:5 where small Pb crystals were distributed evenly.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.6
• /
• pp.645-650
• /
• 2010

In this research, the problem of combustion and its system in Hyundai Heavy Industries and Sachuan Unison will be analyzed in order to provide some methods of thermal efficiency improvement and help to make a positive influence on fuel savings and their productivity. In forging industries, in order to improve the material properties of the industrial heating elements which are being used, depending on different operation conditions of system equipment and combustion systems, fuel consumption and material properties can get a profound influence. Thus, analyzing about combustion system characteristics of 100 tons heating furnace and heat treatment furnace which are in operation in Hyundai Heavy Industry will be done. In usual, air-fuel ratio is proper for capacity of burner installed in each heating device, otherwise burner gets an automatic turn down ratio. It has a profound influence on heating performance and precision of temperature because it is the fixed characteristics of every industrial furnace. Even if there are some methods to improve the heating performance of a furnace installed with a large capacity burner, it is very difficult to obtain the precision of temperature in maintenance interval. Based on this, performance of burner can be drove to best by improving combustion system. Proper Combustion characteristic for each heating interval was analyzed in heating furnace in Hyundai Heavy Industry. A project plan for improving fuel savings and increasing precision of temperature was presented in this research.

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.498-504
• /
• 2006

The etch rates of photoresist (PR) and the etch selectivity of $SiO_2$ to PR in a high density $CHF_3$ plasma were investigated at different ion-incident angles and bias voltages. A Faraday cage was employed for the accurate control of ion-incident angles. The ion energy was controlled by changing bias voltages. The etch rate of $SiO_2$ continuously decreased with ion-incident angles but the etch rate of PR remained constant up to the middle angle region and decreased afterwards. The etch rates of $SiO_2$ normalized to those at $0^{\circ}$ incident angle changed with the ion-incident angle following a cosine(${\theta}$) curve. On the other hand, the normalized etch rates of the PR changed showing a drastic over-cosine shape in the middle angle region. The etch selectivity of $SiO_2$ to PR decreased with an increase in the ion-incident angle because the etch yields of PR were enhanced by physical sputtering in the middle angle region compared to the case of $SiO_2$ etching. The etch selectivity of $SiO_2$ to PR decreased with an increase in the bias voltage at nearly all ion-incident angles.

• 대한위암학회:학술대회논문집
• /
• 2002.04a
• /
• pp.9-17
• /
• 2002

위의 parietal cell 혹은 대식세포와 유사한 세포 내부에서 H. pylori가 발견된다는 보고가 있기는 하나 일반적으로 H. pylori는 Shigella와 같은 침습성 세균은 아닌 것으로 알려져 있다. 그럼에도 불구하고 H. pylori에 감염된 위점막에는 많은 수의 호중구를 위시한 염증세포의 침윤이 관찰되는데 H. pylori가 위상피세포에 부착 할 경우 위상피세포를 자극하여 interleukin-8을 위시한 cytokine 을 발현케하고 이에 의하여 호중구 등의 염증세포가 몰려들게 된다. 한편 고유층에 몰려든 호중구에서는 다시 interleukin-8을 위시한 일련의 호중구 활성화 chemokine을 분비하여 염증반응을 증폭해 나갈 것이다. 호중구에서 발현되는 myeloperoxidase나 활성 산소 등도 위점막의 조직 손상에 기여할 것이다. 위상피세포를 덮고 있는 점액층은 위상피세포를 보호한다고 알려져 있으나 H. pylori 감염의 경우 점액층에 의하여 H. pylori의 운동성이 증가하고 이것이 위상피세포로부터의 cytokine 발현을 자극하여 염증반응을 증폭하는데 관여할 가능성도 있다. H. pylori는 위상피세포에 대하여 apoptosis를 유도함과 동시에 고유층에 몰려든 호중구에 대하여는 apoptosis를 억제케하여 궁극적으로 염증반응을 증폭 및 지속시켜 나가는 쪽으로 작용한다. 한편 H. pylori는 위상피세포로부터 COX-2의 발현을 증가시키는데 이는 위상피세포의 apoptosis를 억제하는 방향으로 작용한다. 이외에 H. pylori의 urease에 의하여 발생한 암모니아나 H. pylori 자신이 분비하는 세포독소가 세포 손상을 유발할 가능성도 있다. 상술한 여러 독성 인자들 중 어느 하나가 단독으로 작용하기보다는 여러 인자가 같이 동시에 또는 시차를 두고 작용할 가능성이 많다고 생각된다.(\gamma-FeOOH)$, 침철광$(\alpha-FeOOH)$, 적금광$(\beta-FeOOH)$, 그리고 자철광$(Fe_3O_4)$이다. 인위적 부식에서는 전부 인철광의 부식물이 생성되었고 자연적 부식에서는 모두 침철광의 부식물이 생성되었다. 특히 철제 표면에 자연적으로 생성된 공식 녹을 XRD 분석한 결과 적금광으로 동정되었다. 이런 모든 시편들을 각 탈염방법에 따라 탈염처리한 후 XRD와 SEM-EDS으로 분석한 결과 인철광과 침철광은 어떠한 변화도 보이지 않았고, 다만 적금광으로 동정된 시편만이 잔존하지 않았다. 철기 제작별 $Cl^-$ 이온 추출량과 탈염효과에 대한 비교 실험은 이온 크로마토그래피 분석 결과와 마찬가지로 단조 철제유물이 주조 철제보다 $Cl^-$ 이온을 많이 가지고 있었으며, 탈염 처리 후에는 $Cl^-$ 이온은 전혀 발견되지 않았다. 이상의 결과 $K_2CO_3$와 Sodium 용액은 탈염처리에서 가장 적합한 탈염처리 용액으로 알수가 있었으며 특히 어떠한 탈염 용액으로 유물을 처리한다 해도 철제유물에 생성된 부식물은 제거되지 않는다는 것을 알게 되었다. 따라서 보존처리자는 유물 표면의 부식 상태만을 보고 처리하기 보다는 철기제작물로 고려하여 처리하는 것이 필요하다. 또한 금속에 부식을 야기시키는 $Cl^-$ 이온과 부식물을 완전하게 제거하여 탈염처리를 하는 것이 유물 부식을 최대한 지연시킬 수 있는 것이라 생각된다.TEX>$88\%$)였다.(P=0.063). 결론: 본 연구에서는 MTHFR C/T & T/T 유전자 다형성이 위암의 발생과 그 위치에 대해 관련이 있는 것으로 여겨지고, 흡연력, 음주력과는 관련이 없는 것으로 여겨진다.험이

• Journal of the Korean Chemical Society
• /
• v.41 no.7
• /
• pp.329-336
• /
• 1997

Photoacoustic spectroscopy was utilized to investigate the carrier transport and the thermal diffusivity in GaAs and Si. From the frequency dependence of the photoacoustic signal, it is found that heat source was originated from the instantaneous thermalization process in low frequency region. In high frequency region, however, the heat was generated by the nonradiative bulk recombination and the nonradiative surface recombination processes. It was also shown that the photoacoustic effects in GaAs of a direct band gap were governed by all three processes and those in Si of an indirect band gap were produced by the instantaneous thermalization and the nonradiative bulk recombination only. The phase of the photoacoustic signal showed a minimum value in GaAs. In Si, the phase of the photoacoustic signal was monotonically decreased as the modulation frequency was increased, demonstrating the above-mentioned mechanisms of the generation of heat. By measuring the photoacoustic signal, thermal diffusivities of semiconductors were determined to be ∼0.35 ㎠/s for GaAs and ∼1.24 ㎠/s for Si. In addition, the similar values of thermal diffusivities were obtained from the curve fitting of photoacoustic phase spectra.