• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.114-121
• /
• 2010

This paper deals with the frequency-dependent grounding impedances of counterpoises relevant to the soil resistivity, the length of counterpoises and the feeding point of test current. The grounding impedances of counterpoises buried in one-layered and two-layered soils were measured and analyzed in the frequency range from 1[kHz] to 10[MHz]. As a result, the frequency-dependent grounding impedances strongly depend on the soil resistivity, and the grounding impedances within the frequency of several tens [kHz] are capacitive behavior in high soil resistivity. When injecting the ground current to the end of counterpoise buried in soil with high resistivity, the grounding impedances in high frequency are increased.

• Electric Engineers Magazine
• /
• s.355
• /
• pp.46-47
• /
• 2012

2012. 1. 17(화) 11:40분경, 강원도 동해시 소재 ${\bigcirc}{\bigcirc}$공장내 변압기실에서 단로기를 개방하지 않은 상태에서 GPT(접지용 변압기)의 접지단자를 접속하는 작업 중에 GPT 상부의 인출된 부상애자의 충전부에 접촉하여 감전 추락 사망한 사고임.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.6
• /
• pp.497-504
• /
• 2021

This paper presents improvement of the reception noise suppression method during formation flights of aircraft. Since aircraft communication equipment is very important for flight mission and safety to perform the functions of internal/external communications, it is required to implement noise-free, clean communication quality, and transmitting/receiving functions. Therefore, the FTA (Fault Tree Analysis) analysis and failure search were performed on the reception noise, and the internal noise of the intercom that affected the reception noise and the none-transmition phenomenon was identified. We changed the multiple grounds of the intercom to a single ground and applied an improved method of filtering the DC Offset voltage. As a result, the voice quality of the communication system of the aircraft was improved through the reduction of the reception noise during formation flights, and it was verified by ground and flight tests.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.133-143
• /
• 2001

This paper describes the correlation of the transient impedance and its parameters with the stationary resistance of a grounding system to a square pulse current and a lightning impulse current. In the experiment, the grounding system consists of a single grounding rod$(\Psi10[mm], 1[m])$and/or a triple-grounding rods of equilateral triangles with 5[m] spacing for operation. To analyze the transient impedance characteristics of the grounding system, a pulse generator which can produce square wave of a 30[ns] rise-time and a $20[\mus] $pulse duration is designed and fabricated. The injected content in the grounding system and the developed potential were recorded, and the time variation of the transient impedance were calculated as the ratio of the potential rising to the injected current at each time. The transient impedance and the effective surge impedance Z3 which defines economic protection level in power system were quite higher than the stationary resistance. The grounding impedance is decreased by the application of the triple-rods grounding system, and its effect is decreased as the frequency of the current is increased due to the inductance of the grounding leads.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.7
• /
• pp.75-79
• /
• 2004

In this paper, a single plane wide band microstrip antenna for integrated circuit as MMIC and LTCC is designed and fabricated. A new configuration for a wide band microstrip antenna with omni-directional pattern is proposed. This antenna consists of two rectangular folded dipoles, which are fed by a coplanar waveguide(CPW). It was effected stabilization ground that a signal plane of CPW feed have been limited ground plane. Therefore, a ground plane of folded structure should be extended outside folded antenna in this research. The characteristics of the proposed antenna were analyzed by using an FDTD methods. The return loss and radiation patterns were simulated and measured. The proposed antenna is get 120MHz bandwidth of PCS band and 250MHz bandwidth of IMT2000 band, used ISM band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.12
• /
• pp.2468-2478
• /
• 1994

A hybrid finite element method is presented for a characterization of scattering an radiation properties of microstrip patch and arrays residing in a cavity recessed in a ground plane. The technique combines the finite element and boundary integral methods to formulate a system for the solution of fields at the aperture and the scattering field and radar cross sections at free space. By virture of the finite element method, the proposed technique is applicable to patch antennas and arrays residing on or embeded in a layered dielectric loss/lossless substrate and is also capable of treating various feed configuration. Several numerical results are presented demonstrating the validity, efficiency and capability of the technique.

• Journal of the Korean Society of Safety
• /
• v.12 no.3
• /
• pp.166-172
• /
• 1997

The BEF on the radial distribution line refers to a class of ground faults in which the load-side power line only is grounded, with the distribution line broken into two parts, the source-side and the load-side. Because its mechanism is remarkably different from that of other earth faults, the fault current is very low, and then difficult to detect the BEF. Thus, it is necessary to analyze its properties and to find an appropriate method that can economically protect the BEF of nonautomation area in the substation. As a result of analyzing the BEF data obtained by the RTDS, EMTP simulation, and the field test data of ETSA, we believe that it is the dominant factor in distinguishing the BEF from normal conditions by a criterion value that is appropriately handled from the zero-sequence current. Thus, with this criterion value, a BEF detecting algorithm is constructed which measures the variations of the zero-sequence current and processes then properly so as to make the fault decision. To prove the accuracy of this algorithm, it is compared with the field test data of ETSA under various conditions. The results show that the proposed algorithm is accurate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.5
• /
• pp.486-487
• /
• 1997

This paper presents the pure capacitive lumped element equivalent circuits for several coplanar waveguide(CPW) discontinuities such as an open-end, an open-end with connected ground planes, a gap and an open-end CPW stub and gives their capacitive element values as a function of physical dimensions of the discontinuity and the frequency for a specific substrate. The capacitive element values are determined from the scattering parameters which are obtained using the finite-difference time-domain(FDTD) method. For an open-end, an open-end with connected ground planes and a gap, the numerical results of the FDTD are compared with the quasi-static results which are calculated using the three- dimensional finite difference method(3D-FDM).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1189-1198
• /
• 2006

We analyze the radiated emission and mutual coupling problem from a single microstrip transmission line and double signal traces with various ground patterns. In this paper, it is shown that the reduction of the radiated emission from the signal traces can be accomplished by using the novel and compact patterns on the ground planes in a specific frequency band. The accuracy and validation of radiation mechanism from the transmission line on a novel ground plane are evaluated and explained by using a commercially available software and experiment, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.244-250
• /
• 2012

This paper describes a 4-Gb/s receiver circuit for a low-swing ground-referenced differential signaling system. The receiver employs a common-gate level-shifter and a continuous linear equalizer which compensates inter-symbol-interference (ISI) and improves voltage and timing margins. A bias circuit maintains the bias current of the level-shifter when the common level of the input signal changes. The receiver is implemented with a low-power 65-nm CMOS technology. When 4-Gb/s 400mVp-p signals are transmitted to the receiver through the channel with the attenuation of -19.7dB, the timing margin based on bit error rate (BER) of $10^{-11}$ is 0.48UI and the power consumption is as low as 0.30mW/Gb/s.