• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.229-231
• /
• 2004

다층 용접이 적용되는 후판 조립 부재에서는 각 조립단계별로 용접변형이 필연적으로 발생되고 있으며 용접변형의 교정을 위한 추가 작업도 각 조립간계 및 후 공정에서 반복적으로 수행되고 있다. (중략)

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.670-677
• /
• 2016

Laboratory and meta-analyses were done for 9% NI Steel for use in a liquefied natural gas carrier. The meta-analysis is based on a previous study. The laboratory analysis examines the effects of a single pass and multiple passes on the tensile strength through an impulse-response test. The tensile strength increased from pass one to pass three and decreased from pass four to pass ten. The pass and multi-pass welding had a positive effect on the tensile strength. Lastly, the welding and tensile time had a positive effect on the tensile strength.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.4 s.37
• /
• pp.709-720
• /
• 1998

In order to study the distribution of welding residual stress through the plate thickness. experiment and analysis of fillet welding details were carried out. Especially, a residual stress in the weld root part of T-joint fillet weld whose measurement was difficult up to now was measured. By using the heat input and the number of the weld layers as parameters, the distribution of the 3-dimensional residual stress was investigated. As a result, we can say that with increasing the heat input, the residual stress in the weld toe and weld root barely changes. But, the area of the tensile residual stress became wide. Then, comparing a single pass with multi-pass weld method, it was found that the residual stress decreased more in multi-pass than in single pass. Moreover, it was found the thing that the area of tensile residual stress by multi-pass is lower than that by single-pass in the near weld part.

• Proceedings of the KWS Conference
• /
• 1993.05a
• /
• pp.41-44
• /
• 1993

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.173-174
• /
• 2000

• Proceedings of the KWS Conference
• /
• 1994.10a
• /
• pp.127-129
• /
• 1994

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11b
• /
• pp.557-562
• /
• 1996

조사전 및 감시시험시 용접열영향부(heat affected zone, HAZ)의 인성평가를 위해 제작되는 샤피(Charpy) 충격시험편의 노치(notch) 위치에 대하여 현재의 규정에 대한 타당성을 검토하였다. 적용규정은 HAZ 시험편의 노치위치를 용접용융선(fusion line, FL) ＋ 모재측 0.8 mm 로 제한하고 있다. 그러나, 본 연구결과, 이 부위는 다층(multipass) 용접시 후속열이력에 의해 결정립이 미세화되어, 인장강도와 경도 및 충격인성이 모재나 용접부에 비하여 양호하게 나타났다. 한편, FL ＋ 4 mm 이상의 다른 위치에서는 강도와 경도 및 충격인성이 모두 모재와 용접부에 비하여 낮은 값을 보였다. 이는 다층용접에 의한 후속열이력 및 용접후열처리(post weld heat treatment, PWHT)에 의해 금속조직학적 영향을 받은 것으로 판단되었다. 일련의 시험결과로부터, 조 사전 및 감시시험용 샤피충격시험편의 HAZ 에 있어서의 노치위치에 대한 현재의 규정을 재검토할 필요가 있음을 제안하였다.

• Proceedings of the KWS Conference
• /
• 1997.05a
• /
• pp.133-136
• /
• 1997

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.215-216
• /
• 2004

최근 해양구조물의 수직 칼럼부 용접 공법은 FCAW에 의한 다층 용접으로, 작업 시수와 작업자의 피로 가중 등, 생산 효율면에서 단점이 많았다. 이를 개선하기 위해 최초로 EGW에 의한 단층 용접을 적용하고자 EGW 적용시의 용접강도 및 피로 안전성을 평가하기 위한, 피로 시험을 수행하였다. (중략)

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.85-94
• /
• 1998

Welding fabrication invariantly involves three district sequential steps: preparation, actual process execution and post-weld inspection. One of the major problems in automating these steps and developing autonomous welding system, is the lack of proper sensing strategies. Conventionally, machine vision is used in robotic arc welding only for the correction of pre-taught welding paths in single pass. In this paper, developed vision processing techniques are detailed, and their application in welding fabrication is covered. The software for joint tracking system is finally proposed.