• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.378-383
• /
• 2004

Orthogonal Frequency Division Multiplexing (OFDM) transmits high-speed data by splitting the transmission bandwidth into a number of subcarriers. The bandwidth of each subcarrier is ensured to be smaller than the coherence bandwidth. This paper presents an OFDM system incorporated with the Carrier Interferometry (CI) codes to improve the performance by enhancing frequency diversity effect. The performances of CI-OFDM with multilevel modulations are investigated in highly dispersive fading channels. For the investigation of performance improvement of CI-OFDM, a simulator has been developed using a well-known SPW simulation platform. The simulation results show that the CI-OFDM provides both performance improvement and robustness against dispersive fading channel behavior. The performance of CI-OFBM with multilevel modulations demonstrates that CI-OFDM outperforms a traditional OFDM system, particularly in highly dispersive channels. With a relatively large delay spread of 151㎱ compared to the guard interval of 800㎱, CI-OFDM provides a BER of 10$^{-3}$ if sufficient signal power is present.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.3
• /
• pp.179-185
• /
• 2017

The problem that occurred in the design/fabrication/testing of the wideband transmitting power amplifier for an embedded active SONAR (Sound Navigation and Ranging) system operating underwater was analyzed and the solution of the problem was proposed in this paper. Wideband acoustic SONAR systems had been developed in order to improve the underwater detection performance. The underwater acoustic transmission system had been also developed to achieve the wideband SONAR system. In this paper, the wideband acoustic transmission signal was generated using a 2 Level sawtooth type Class D PWM (Pulse Width Modulation) which was not complicated to implement. When the sonar signals having two or more frequencies were simultaneously generated, parasitic frequencies were added to the original signals by integer multiples of the frequency difference of the original signal. To cope with this problem, we proposed a way to remove the parasitic frequency from the source signal through modeling and simulation of the implemented power amplifier and PWM control hardware using MATLAB and Simulink.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.5
• /
• pp.47-53
• /
• 2007

The purpose of IEEE 802.16j is to extend coverage and to enhance throughput by using relay station additionally to conventional IEEE 802.16e . The cellular system experiences performance degradation at the cell edge due to pathloss, shadow and multipath fading. We can get advantage of spatial diversity gain by using relays more than two cooperatively in the IEEE 802.16j system. Cooperative relaying using space-time code provides better performance under multipath fading and has more robustness against the shadow fading than single relaying. In this paper, we investigate the performance of IEEE 802.16j using cooperative relaying by link level simulation. We also show that the cooperative relaying system achieves better performance than the conventional single relaying system. We apply realistic shadow model considering correlations between shadow fadings of different relaying paths. It is shown that the performance of the system depends highly on the spatial location of relay stations.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.6 s.360
• /
• pp.31-39
• /
• 2007

In this paper, a system for real-time or periodic measurement and analysis of RF parameters such as forward transmit power and pilot power in CDMA base station systems is proposed. Such RF characteristic parameter measurement can be prevented from system fault and used to achieve optimal service quality and maximum investment return through cell coverage expansion, subscriber capacity increase and so on. For forward power measurement, the local oscillator frequency for the detector is varied so that the transmit power for all channels can be measured. The channel power measurement can be used to analyze the variation in transmit power for changes in voice traffic. By comparing to forward $E_c/I_o$, the pilot channel power can be deducted, which can be used to determine uy degradation in transmit section modules such as the high dover amplifier. Since an accurate analysis of carefully measured data using the CDMA level detector must be made, the system is designed so that measurement errors due to changes in crest factor with modulation method can be overcome.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.4
• /
• pp.59-68
• /
• 2009

This paper addresses a hybrid multi-focus image fusion scheme using the recent curvelet transform constructions. Hybridization is obtained by combining the MS fusion rule with a novel "copy" method. The proposed scheme use MS rule to fuse the m most significant terms in spectrum of an image at each decomposition level. The scheme is dubbed in this work as m-term fusion in adherence to its use of the MSC (most significant coefficients) in the transform set at any given scale, orientation, and translation. We applied the edge-sensitive objective quality measure proposed by Xydeas and Petrovic to evaluate the method. Experimental results show that the proposed scheme is a potential alternative to the redundant, shift-invariant Dual-Tree Complex Wavelet transforms. In particular, it was confirmed that a 50% m-term fusion produces outputs with no visible quality degradation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.8
• /
• pp.75-84
• /
• 2004

In this paper, we proposed an efficient hardware architecture of line-based lifting algorithm for Motion JPEG2000. We proposed a new architecture of a lifting-based filtering cell which has an optimized and simplified structure. It was implemented in a hardware accommodating both (9,7) and (5,4) filter. Since the output rate is linearly proportional to the input rate, one can obtain the high throughput through parallel operation simply by adding the hardware units. It was implemented into both of ASIC and FPGA The 0.35${\mu}{\textrm}{m}$ CMOS library from Samsung was used for ASIC and Altera was the target for FRGA. In ASIC, the proposed architecture used 41,592 gates for the lifting arithmetic and 128 Kbit memory. For FPGA it used 6,520 LEs(Logic Elements) and 128 ESBs(Embedded System Blocks). The implementations were stably operated in the clock frequency of 128MHz and 52MHz, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.6
• /
• pp.689-697
• /
• 2016

In this paper, we design and implement SPA (Switched Parasitic Antenna) antenna which can control its beampattern using multiple parasitic elements. By applying SPA antenna to wireless communication system and implementing beamforming scheme, we show that SPA antenna can be used to improve the performance of wireless communication systems. SPA antenna consists of a single active antenna and multiple parasitic elements around the active one, and can control its beampattern by switching the parasitic elements. Using this characteristic of the SPA antenna, it is possible to impelemtent beamforming technique with single RF chain, which enables to design low cost, low complexity and low power wireless communication systems. In order to verify the beamforming gain, we measure and analyze the system level performance, such as SNR, PER, and throughput.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.280-288
• /
• 2009

In this paper, a high-power and low-loss stripline 10-way power divider is designed and fabricated fur the feed network of an S-band linear array antenna with Chebyshev current distribution which has a narrow beam width and low side lobe level(SLL) of 35 dB or more. The unit cell of the power divider is based on a T-junction power divider and the whole divider is comprised of the cascaded unit cells. The multi-stage impedance transformer and modified ring hybrid are used in designing the power divider for performance improvement. And the reflection loss and insertion loss are improved by modifying a connector structure for a coaxial-to-stripline transition.

• Journal of KIISE:Computing Practices and Letters
• /
• v.5 no.6
• /
• pp.738-747
• /
• 1999

본 논문에서는 분산 실시간 시스템의 특징인 분산 처리 과정의 신뢰성을 지원하기 위한 동적 트랜잭션 처리 구조를 연구하였다. 실시간 분산 처리 환경에서 동적으로 발생하는 실시간 분산 트랜잭션 처리를 위하여 트랜잭션 내에 필수적인 3가지 언어적 특성들을 제시하였다. 첫째는 트랜잭션 내에 실시간 시스템의 가장 중요한 특징인 시간적인 제약 조건들을 정의 할 수 있는 방안을 제시하고, 둘째는 비동기적인 처리 성격을 지닌 실시간 특성을 고려한 비동기적 트랜잭션 처리 방법을 제시한다. 또한, 분산 처리 과정에서 발생되는 예외 사항들을 처리하기 위하여 긴급성을 고려한 다중레벨 우선순위 스케줄링 (Multi-Level Priotiry Scheduling)이라 부르는 트랜잭션 스케줄링 방안을 제시한다. 그리고, 제시한 실시간 분산 트랜잭션 처리 구조의 타당성 및 가능성을 입증하기 위한 실시간 트랜잭션 처리 과정을 시물레이션을 통하여 제시한 언어적 특성에 대한 고려 사항들을 보여준다.Abstract We propose a dynamic transaction processing model that supports a reliability for distributed real-time processing. For the dynamic processing in distributed real-time transaction systems, we suggest three features that are defined in programming language. First, we propose a specification model to explicitly define the time constraints, needs in real-time distributed processing. Second, we describe an asynchronous transaction processing mechanism based on the real-time characteristics. So, we suggest three communication primitives to support asynchronous transaction processing. Lastly, a scheduling policy based on urgent transaction is suggested to manage the exception occurred during the distributed processing. This scheduling policy is called multi-level priotiry scheduling (MPLS). Based on three features and scheduling policy, we describe a direction to manage a dynamic transaction processing in distributed real-time systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.1
• /
• pp.70-78
• /
• 2019

In this paper, modeling of a high-resolution multi-function radar is proposed to simulate radar performance in a war game simulator, called AddSIM. To incorporate the multi-function radar model into the AddSIM, the modeling must comprise a component-based structure consisting of physics, logics, and information blocks. Therefore, we assign the RF hardware of a RADAR as the physic block, a controller as the logics block, and the RF specifications of the RADAR as the information block. Detailed modeling of the physics and logics blocks are addressed, and data structure is also presented on an engineering level. On a multi-target engaged scenario, the performance of the multi-function radar is numerically analyzed and its validation is examined.