• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.111-111
• /
• 2004

회전축계는 발전기의 터빈이나 가스터빈 그리고 항공기의 회전익, 선박, 자동차등 산업전반에 널리 사용되어지고 있다. 이러한 회전축계의 안정성 확보와 성능향상을 위해서는 정확한 동적 모델링이 필요하며 지금까지 많은 연구가 되어 왔다. 일반적으로 회전축계의 동특성 이론 모델은 회전관성, 자이로모멘트, 전단변형을 포함하는 티모센코 축 요소를 널리 사용하고 있으며, 많은 연구를 통해 그 유용성이 입증되어 왔다.(중략)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.9
• /
• pp.875-882
• /
• 2011

In the present study, the imbalance in the axial-thrust and variation in the volumetric efficiency that occurred during the trimming of impeller diameter were investigated. The present study was focused on low-specific-speed multistage centrifugal pumps with a balancing piston as the balancing mechanism. The effects of impeller trimming on the axial-thrust balance in multistage pumps with horizontal and vertical axes were compared. The results showed that impeller trimming resulted in an additional axial-thrust acting in direction of pump inlet. The axial-thrust imbalance due to impeller trimming was more severe in the vertical-axis pumps than in the horizontal-axis pumps. The rate of increase in the diameter of the balancing piston, which was proportional to the rate of impeller trimming, was evaluated to maintain the axial-thrust balance. Furthermore, a simultaneous increase in the piston length and piston diameter was more effective for reducing the axial-thrust imbalance along with the volumetric efficiency drop.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.506-508
• /
• 2013

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.114-119
• /
• 1997

Natural vibration of the rotor system having multi-step cross-sections is analyzed. The rotary inertia and the shear deformation are considered. Torque is also included in order to simulate the power transmission system. The complex displacement and the variable separation are introduced. The exact solutions in uniform cross-section segment and the boundary conditions are used. Natural frequencies and mode shapes are obtained, especially the mode shapes are countinuous.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.583-591
• /
• 2014

The mathematical modeling on the free vibration and stability of a multi-stepped shaft of turbo compressor is performed in this study. The multi-stepped shaft is modeled as a non-uniform Timoshenko beam supported by anisotropic bearings. It is assumed that the shaft is spinning with constant speed about its longitudinal axis and subjected to a conservative axial force induced by front and rear impellers attached to the shaft. The structural model incorporates non-classical features such as transverse shear and rotary inertia. A structural coupling between vertical and lateral motions is induced by Coriolis acceleration terms. The governing equations are derived via Hamilton's variational principle and the equations are transformed to the standard form of an eigenvalue problem. The implications of combined gyroscopic effect, conservative axial force, bearing stiffness and damping are revealed and a number of pertinent conclusions are outlined. In this study analytical results are compared with those from ANSYS finite element analysis and experimental modal testing.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.55-60
• /
• 2020

As research and development of eco-friendly vehicles are expanding worldwide, additional devices of vehicles are reduced or deleted to increase the mileage, or research is being conducted to reduce weight. Among them, the multi-stage transmission that was applied to the internal combustion engine vehicle was deleted and replaced with a reducer, and the initial driving power is secured by increasing the torque through the control of the motor output value. However, since frequent motor speed change can result in a load increase, this study attempts to develop a compact and lightweight manual two-stage reducer with a general reducer structure. Therefore, a two-speed transmission with two gear ratio was designed by inserting a large gear and a small gear in a structure with a parallel shaft to connect the gears with a V-belt in the form of a parallel shaft reducer, and setting the gear ratio of the low and high gears respectively. In addition, power performance according to the rotational speed and load of the transmission was checked through a test, and the heat generation characteristics generated during driving were checked to verify the validity of the transmission.