• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.39-48
• /
• 2012

In case a measurement output of gyro sensor is an accumulated angle counts, it is usually provided as a binary bit counter which is allowed to roll-over at its maximum or minimum value. And it is a well known fact that the roll-over behavior restricts the measurement range of the processed sensor output below the actual measurable range of sensor hardware itself. In this study, a conventional sensor data processing method for a gyro with an accumulated angle output is introduced. And also, an improved method which can extend the processed output range over the conventional one is proposed. It is also derived that the increased range depends on the variation speed of a input signal. Finally, the derived equations and the performance of the proposed algorithm are verified using a computer simulation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.9
• /
• pp.65-72
• /
• 2011

A binary integration is one of sub-optimal pulse integration which decides detection based on discriminating m successful detections out of n trials in radar systems using multiple pulse repetition frequencies. This paper introduces target measurement error reduction technique to reduce azimuth errors in suboptimal binary integration radar which applies the near value by m rather than the optimal m and verifies the performance by analyzing the experimental data measured from real radar.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.2
• /
• pp.39-45
• /
• 2017

This paper is to grasp the applicability of a cumulative rebound angle measured from the rebound action generated after impacting an object for the assessment of compressive strength of construction materials nondestructively and to propose the test results. For this study, an impact device was devised and used for impacting an object by an initial rotating free falling impact and following repetitive impacts from the rebound action which eventually disappears. Five types of construction materials, which are soil cement, cement paste, wood (pine tree), and two types of rock (shale and granite), were tested and both peak rebound angle and cumulative rebound angle were measured for each material by using a high-speed camera. The measured angles were compared with the directly measured compressive strength for each material. The comparison showed that for materials such as cement and rock the cumulative rebound angle, which reflects energy dissipation, rather than the peak rebound angle is more appropriate indicator for assessing the compressive strength of a material, but for a construction material such as wood which has a high toughness the magnitude of rebound is not an indicator to assess the compressive strength of a material.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.12
• /
• pp.69-78
• /
• 2016

A suction bucket foundation has been considered to be a potential foundation type for offshore wind turbines. A suction bucket foundation is usually installed in soft soil, so the accumulated displacement of the foundation may occur under long-term cyclic loads. In this study, a series of 1-g model tests were performed to analyze the accumulated rotation of suction bucket foundations under long-term cyclic horizontal loads. The dry model ground was prepared to have two different soil densities by air-pluviation method. The model tests were performed varying the embedment depth of the suction bucket, the soil density, and the amplitude of cyclic load. A one-way horizontal cyclic load was applied over $10^4$ cycles. Test results showed that the accumulated rotation of the suction bucket foundation increased with the increase in the number of cycles and load magnitudes. Based on the model test results, a new equation was proposed to evaluate the accumulated rotation of the suction bucket foundations in dry sandy ground under long-term cyclic horizontal loads.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.9
• /
• pp.585-591
• /
• 2006

Generalized Processor Sharing(GPS) model provides instantaneous fair services to currently backlogged sessions. Since this fair service distributes server capacity to backlogged sessions in proportion to their weights, the fairness is only valid between the sessions serviced at the same time. From the long time view, however, this fair service provides different server capacity with one session or another, even if these sessions have the same weights. This paper proposes a cumulative fair service(CFS) model to provide fair server capacity to all sessions in the long time view. This model provides fair service in session Viewpoint because it distributes server capacity in proportion to the weights of sessions. The model and an algorithm referencing that model are analyzed for their properties and performances. Performance evaluations verify that the proposed algorithm provides proportional service capacity to sessions in the long time view.

• Proceedings of the KOR-KST Conference
• /
• 1998.10a
• /
• pp.11-20
• /
• 1998

정적 통행배분모형은 도로 건설 등 공급부문에의 적용은 가능하나 통행량 및 혼잡의 시간적 공간적 변화를 고려하지 못하여 수요관리에서는 교통량 및 비용에 대한 관측치와 모형의 결과치가 상이한 문제가 있다. 이에 동적배분모형의 다양한 접근방법이 시도되고 있는데 그 중 Simulation기법을 개발하고자 하였다. 모형은 개별차량의 시공간상 움직임을 포현하고자 절대시간이 가장 이른 차량순으로 시뮬레이션을 함으로써 선입선출(FIFO)을 가능하게 하였다. 각 차량별 지체시간의 계산은 대기행렬 이론을 기초로 한 누적곡선법을 적용하여 도출하였다. 개별차량 Simulation은 시간축으로 확장된 연속류 Network상에서 각 차량의 도착 및 출발할 노드와 시간대를 결정하면 모든 지점에서 누적도착, 출발곡선을 그릴 수 있으며 이를 통해 도로구간에 있어 시간대별 통행시간, 밀도, 속도 등을 파악할 수 있다. 또한 합류부의 용량와 와해현상과 분류부의 용량변화현상 제약 및 Queue길이 제약이 이루어지도록 하였다. 개발된 모형의 검증은 영동대교 북단 강변도로 진출입부 자료를 실측하여 사용하였다. 모형은 합류부 용량와해의 적용 전과 후의 결과를 각각 실측치와 비교하였다. 용량와해현상을 적용한 모형에서 MAPE 10%미만의 우수한 예측력을 보였다. 이는 누적곡선을 이용한 Simulation모형이 현실에 가까움을 의미하는 것이며, 합류부 용량와해현상의 관계식을 보다 정교하게 도출하고 분류부에도 이를 적용한다면 모형의 예측력은 더욱 향상될 것으로 보인다.

• Journal of the Korea Society for Simulation
• /
• v.25 no.2
• /
• pp.83-92
• /
• 2016

Tolerances are defined as the allowable variations in the geometry and positioning of parts in a mechanical assembly for assuring its proper functionality. Tolerance analysis is the activity related to estimating the potential accumulated variation in assemblies. If the estimated variances go out of the specified ranges, it causes the quality problem. Thus, we should adjust the tolerances and this activity is called as tolerance design. In this paper, a case study on the accumulated tolerance analysis and design using Monte Carlo simulation is introduced, which is applied for developing a portable medical device. Using the simulation study, we can improve the assemblability and functionality of the product.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.26-26
• /
• 2003

본 연구에서는 누적압연접합공정(ARB)을 통하여 5052 알루미늄 합금의 결정립을 약 0.2$\mu\textrm{m}$ 크기로 미세화 하였다. 누적압연에 의한 변형량 증가에 따른 미세 조직 변화와 결정립 간의 상대적인 방위각 차이를 TEM을 이용하여 관찰하였다. 누적 변형량을 함수로 상온 인장특성을 분석하였고, 초미세립 소재를 후속 열처리한 후 미세 조직 변화를 관찰하여 제조된 초미세립 소재의 열적 안정성을 평가하였다. 상온 대기 중에서 pin-on-disk 형태의 마멸시험기를 사용하여 초미세립 소재의 미끄럼 마멸시험을 변형량과 하중을 변수로 행하였다. 강소성 변형에 의해 제조된 5052 알루미늄 합금 소재의 마멸저항성은 강소성 변형 전과 비교하여 소재의 경도가 크게 증가하였음에도 불구하고 오히려 감소하였다. 마멸시험 후 마멸면의 SEM, 마멸단면의 OM 관찰과 마멸면 직하의 깊이에 따른 경도측정을 통하여 초미세립 소재의 마멸기구를 분석하였고 마멸표면의 변형 층을 관찰하였다. 또한 마멸면 직하 조직의 TEM 관찰을 통해서 마멸시험 중의 미세 조직 변화를 연구하였다.

• The Journal of the Korea Contents Association
• /
• v.9 no.1
• /
• pp.304-311
• /
• 2009

This article proposes a new time-based depreciation method using the accumulated depreciation rate function. The method can systematically compute the depreciation charge of each period, in every case where the charge is constant or decreasing or increasing, and solve the problems of depreciation methods currently used, by obtaining the accumulated depreciation charge at any given time. We can choose diverse rational depreciation types for the characteristic of every asset with the new method, and compute the depreciation charge with consistency in all cases where assets are owned for partial period.

• The Journal of the Korea Contents Association
• /
• v.3 no.1
• /
• pp.58-63
• /
• 2003

In this paper, an object tracking system in a known environment is proposed. It extracts moving area shaped on objects in video sequences and decides tracks of moving objects. Color invarianoe features are exploited to extract the plausible object blocks and the degree of radial homogeneity, which is utilized as local block feature to find out the block correspondences. The experimental results are given.