• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.3
• /
• pp.52-62
• /
• 1994

기계나 구조물 파괴의 대부분은 노치부를 기점으로 하여 발생하기 때문에 첨단복합재료를 노지부 재로서 안전하면서도 경제적으로 사용하기 위해서는 각종 조건하에 있어서 강도특성을 명확히 하는 것은 대단히 중요하다. 본 연구에서는 노치를 갖는 복합재료를 이용하여 각종조건하에서 강도특성평가실험을 행하였으 며, 얻어진 결과를 종합하면 다음과 같다. (1) 첨단복합재료 노치재는 試驗片의 幾可學的 形狀과는 관계없이 노치반경 p만에 의해 결정되는 최대탄성응력 $\sigma_{max}$일정의 條件下에서 破t짧된다. (2) 破斷時 최소단면에서의 공칭응력 $\sigma_{c}$와 응력집중계수 $K_{t}$와의 관계에 있어서,$\sigma_{c}$의 값이 $K_{t}$의 증대와 더불어 떨어지고 있는 부분과, $K_{t}$와 관계없이 거의 일정하게 되고 있는 부분으로 나누어지는 現象은 노치재의 回轉굽힘 또는 인장압축파열에서 보여지는 현상과 外觀上 對應하고 있다. 즉, 정적파괴와 피로파괴는 파괴의 양상이 비슷하다 (3) PEN수지단체의 경우, 피로균열발생은 점발생적 피로균열이 최대탄성응력에 의해 지배되며, 노치에 만감하며,균열전파수명은전수명에 비해 상당히 짧다. (4) 단탄소섬유강화복합재료의 경우, 피로균열은 섬유端에 응력이 집중하기 때문에 일반적으로 섬유端에서 아주 빠른 시기에 발생하지만, 섬유가 피로균열진전에 대해 방해물로 작용하기때문에 아주 천천히 전파한다. (5) 短탄소鐵維는 피로균열발생에 대해서는 負의 강화작용 전수명의 극히 초기단계에 피로균열 발생을, 피로균열전파에 대해서는 正의 강화작용을 한다. (6) 단탄소섬유를 PEN에 강화함으로 인해 정적강도 보다 피로강도에 더 큰 강화효과를 초래했으며, 선형노치역학의 개녀은 첨단 복합재료의 강도평가에 대단히 유효했다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.8
• /
• pp.693-701
• /
• 2016

In this study, notch defects are evaluated using fracture mechanics. To understand the effects of notch defects, FE analysis is conducted to predict the limit load and J-integral for middle-cracked and single-edge cracked plates with various sizes of notch under tension and bending. As the radius of the notch increases, the energy release rate also increases, although the limit load remains constant. The values of fracture toughness($J_{IC}$) of SM490A are determined for various notch radii through FE simulation instead of conducting an experiment. As the radius of the notch increases, the energy release rate also increases, together with a more significant increase in fracture toughness. To conclude, as the notch radius increases, the resistance to crack propagation also increases.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.2
• /
• pp.71-75
• /
• 1992

기구나 구조물의 피로수명은 노치에서의 피로균열 방생수명에 의하여 지배되기때문에 노치로 인한 피로강도감소계수 $K_f$는 피로설계상 대단히 중요한 인자이다. 노치 선단(Notch root)에서의 피로균열발생명수 N$_c$를 기준으로하면 탄성응력집중계수 $K_t$가 10 정도까지 $K_f$와 $K_t$간에는 거의 직선적인 관계가 있음이 이다- 고에 의하여 명석해졌으나 이는 인장,압축의 축력이 작용하였을 때이며 따라서 기구나 구조부재는 축력외에도 굽힘 피로 하중이 작용하였을때도 많으므로 본 연구에서는 굽힘 피로 하중을 받았을때도 있다. -고의 결론이 적용되는지는 검시코져 본 연구를 실시하였다.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.19-29
• /
• 1993

The static tensile tests of GFRP, ID300, CFRID300 and CFRPEEK were made on the plain and notched specimens at room temperature. The results were discussed based on linear notch mechanics which was proposed by H.Nistani. The fracture of notched GFRP, ID300, CFRID300 and CFRPEEK specimens is controlled by the elastic maximum stress, $({\sigma}_max)$, and the notch root racius,$\rho$, alone, independently of the other geometrical conditions. The relation between fracture nominal stress,$({\sigma}_max)$, and stress concentration factor, $K_t$ and a part where $({\sigma}_c)$ is nearly constant independent of $K_t$. A similar phenomenon can be seen in the fatigue tests of notched specimes under rotating bending or push-pull. The almost constant $({\sigma}_c)$ values correspond to the nearly constant apparent stress intensity factor, $K_{1pc}$ values, obtained by assuming ,$\rho$=0. This can be attributed to the existence of the stable crack. Linear notch mechanics is very useful for analyzing the static tensile fracture behavior of notched GFRP, ID300, CFRPEEK specimens.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.217-222
• /
• 2001

For the life evaluating of notched members, it is the best way that performing the real fatigue test of structure containing notch. But this method required generally much times and costs to evaluate fatigue life. So, generally we use the modified S-N curve or several methods to predict fatigue life. In this study, crack initiation life was evaluated by fatigue testing the SAE keyhole specimen and smooth specimen made of Al 7075-T6 alloys using the constant load then obtained S-N curve of smooth specimen and P-N curve of SAE keyhole specimen. And, fatigue lives of keyhole specimen are predicted using some life prediction methods (Nominal range I method, Nominal range II method, FEM analysis) for investigating experimented results, and that were compared with experimental data. Predicted fatigue lives by FEM analysis were corresponded with experimental data between 1/3times and 3times on the whole, and predicted fatigue lives using modified S-N curve (Nominal range I method, Nominal range II method) were nonconservative compared with that of FEM analysis.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.2
• /
• pp.41-53
• /
• 1994

In this paper, rotating-bending fatigue tests of the SiC-whisker- reinforced 6061-T6 aluminum alloy and 6061-T6 alumiunm alloy made by power metallurgy were carried out to investigate the fatigue characteristics of plain and notched specimens at room temperature. The fatigue mechnisms in both materials were clarified through successive surface observations using the plastic replica method. In the case of the SiC-whisker-reinforced composites, there are whisker rich and poor zones and the fatigue crack is nucleated from the end of whiskers near the boundary. On the other hand, in the case of the 6061-T6 aluminum alloy, the fatigue crack is nucleated from defects and propagates by shear. Moreover, the results were discussed based on linear notch mechanics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.195-196
• /
• 2006

• Journal of Korea Multimedia Society
• /
• v.12 no.10
• /
• pp.1407-1417
• /
• 2009

Today is the Information age which Internet service acts a most important Information Source. So the Power Line Communication has been achieved to offer Internet service for Last-Mile area. And Research is achieved to frequence range from 30MHz to 80MHz for High-speed communication service. But, Power Line is not suitable for communication, So, electric wave is generated from flow of communication information. And the electric wave is interfered with Wireless Communication Service using the same frequence range. In this paper, a Notch Filter for reduce of interference between Power Line Communication and Wireless Communication Service is proposed. The proposed emulator is developed using TMS320C6416T DSP board of Texas Instruments.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.4
• /
• pp.1-4
• /
• 2009

This work shows how the adoption of a dual-dicing process for silicon wafer separation affects the thermal-cycling reliability (i.e. $-65^{\circ}C$ to $150^{\circ}C$) of the semiconductor devices utilizing lead-on-chip (LOC) die attach technique. In-situ examinations show that conventional single-dicing process directly attacks the edge region of diced devices but dual-dicing process effectively protects the edge region of diced devices from dicing-induced mechanical damage. Probably, this is because the preferential and sacrificial fracture of notched regions induced on the active surface of wafers saves the edge regions. It was also investigated through thermal-cycling tests that the number of thermal-cycling induced failures is much lower at the dual-dicing process than the single-dicing process.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.145-148
• /
• 2003

This paper describes a new notches generator for the test of custom power devices such as UPS, DVR, Active Power Filter, etc. The magnitude, width, polarity, and position of the notches generated by the proposed scheme can be varied with simple control. The scheme has good features of simple structure, high reliability, and the capability of arbitrary several notches generation. The circuit operation is described and the usefulness of the scheme is verified through simulations.