• Korean Journal of Materials Research
• /
• v.5 no.7
• /
• pp.835-841
• /
• 1995

The deposition properties of Si$_3$N$_4$ deposited by low pressure chemical vapor deposition were studied to evaluate Si$_3$N$_4$as part of multi-layer coatings for anti-oxidation and anti-wear coating of graphite in the propellant-burning environment. Si$_3$N$_4$was deposited on the pack-SiC coated graphite and the tendencies of deposition rate and surface morphology changes with temperatures and reaction gas ratios were investigated. In low deposition temperatures the deposition rate increased tilth increasing temperature but in high temperatures the deposition rate decreased with increasing temperature. The grain size of Si$_3$N$_4$decreased with increasing temperature. In condition that the range of reaction gas ratios is 20$\leq$NH$_3$/SiH$_4$$\leq$40, the deposition rate and surface morphology did not change. The Si$_3$N$_4$deposited at 800~130$0^{\circ}C$ was amorphous, and by post-annealing at 130$0^{\circ}C$ in a $N_2$ambient, the Si$_3$N$_4$crystalized.

• Clean Technology
• /
• v.27 no.4
• /
• pp.332-340
• /
• 2021

With the recent reinforcement of emission standards, it is necessary to make efforts to reduce NOx from air pollutant-emitting workplaces. The NOx reduction method mainly used in industrial facilities is selective catalytic reduction (SCR), and the most commercial SCR catalyst is the ceramic honeycomb catalyst. This study was carried out to reduce the NOx emitted from steel plants by applying De-NOx catalyst coated on metallic monolith. The De-NOx catalyst was synthesized through the optimized coating technique, and the coated catalyst was uniformly and strongly adhered onto the surface of the metallic monolith according to the air jet erosion and bending test. Due to the good thermal conductivity of metallic monolith, the De-NOx catalyst coated on metallic monolith showed good De-NOx efficiency at low temperatures (200 ~ 250 ℃). In addition, the optimal amount of catalyst coating on the metallic monolith surface was confirmed for the design of an economical catalyst. Based on these results, the De-NOx catalyst of commercial grade size was tested in a semi-pilot De-NOx performance facility under a simulated gas similar to the exhaust gas emitted from a steel plant. Even at a low temperature (200 ℃), it showed excellent performance satisfying the emission standard (less than 60 ppm). Therefore, the De-NOx catalyst coated metallic monolith has good physical and chemical properties and showed a good De-NOx efficiency even with the minimum amount of catalyst. Additionally, it was possible to compact and downsize the SCR reactor through the application of a high-density cell. Therefore, we suggest that the proposed De-NOx catalyst coated metallic monolith may be a good alternative De-NOx catalyst for industrial uses such as steel plants, thermal power plants, incineration plants ships, and construction machinery.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.1
• /
• pp.36-40
• /
• 2003

The diamond-like nanocomposite (DLN) thin films were deposited on Si substrates using $CH_4/(C_2H_5O)_4Si/H_2$/Ar gas mixtures as source gases by the plasma enhanced chemical vapor deposition (PECVD). The chemical structure and microstructure of grown films were investigated and their tribological properties were evaluated by a ball-on-plate type tribometer. The deposited DLN films mainly consisted of diamond-like a-C:H and quartz-like a-Si:O networks. The DLN films had a good agreement with tribological coating applications due to their extremely low friction coefficients and low wear rates.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.2
• /
• pp.57-62
• /
• 2007

The lubricational characteristics about friction wear has an effect on the material quality of surface. In this paper, we studied the lubricational characteristics through the surface modification experiment by spray coating the surface with $MoS_{2}$ and PTFE solid lubricants. In the case of $MoS_{2}$ and PTFE coating, the friction coefficient of Journal is lower than that for noncoating so the friction characteristics is excellent. In particular, the beginning characteristics of $MoS_{2}$ coating is excellent, and in the case of PTFE coating, seizure dose not appear seizure. $MoS_{2}$ and PTFE coating are excellent in the extreme pressure at high load. The wear characteristics is excellent in the following order; PTFE < $MoS_{2}$ < Non Coating. For Non coating, seizure appears at the beginning due to the heat, but in the case of $MoS_{2}$ and PTFE coating, it will have the excellent heat stability even at high temperature.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.6
• /
• pp.391-399
• /
• 1997

To figure out wheher the tribological properties of a hras-coating layer can be imporved by ion implantatio, TiN-coated SKD 11 61 were implanted with nitrogen ion and their wear peoperties were examined systematically. The amount of nitrgen ione implanted on the coating layer was $2 \times 10^{15},\;10^{16},\;10^{17},\;and\;10^{18}\;ions/\textrm{cm}^2$, respectively. X-ray diffraction revealed theintensity of the peaks belong TiN tended to increase as the ion dose increased, which implied that the implantation promoted the formation of TiN in the coated later. Howeverthe hardensity of the specimens increased then decreased again as the ion dose increased, resulting in a obvious drop of the hardness for the ion does of $2 \times 10^{18}\;ions/\textrm{cm}^2$<\TEX>. While the adhesion of the coated layer of SKD 61 was excllent regrdless of the implatation, the adhesion of the later of SKD 11 was apparently improved by the implantation. The overall wear properties of SKD 11 was better than that of SKD 61, and the best result was yielded at the ion dose of $2 \times 10^{15}\;ions/\textrm{cm}^2$<\TEX>.

• Journal of Biomedical Engineering Research
• /
• v.25 no.2
• /
• pp.157-163
• /
• 2004

Nitrogen ion implantation and ion plating techniques were applied for improvement of the wear resistance of metallic implant materials. In this work, the wear dissolution behaviour of a nitrogen ion implanted super stainless steel (S.S.S, 22Cr-20Ni-6Mo-0.25N) was compared with those of S.S.S, 316L SS and TiN coated 316L SS. The amounts of Cr and Ni ions worn-out from the specimens were Investigated using an electrothermal atomic absorption spectrometry. Furthermore, the Ti(Grade 2) disks were coated with TiN, ZrN and TiCN by use of low temperature arc vapor deposition and the wear resistance of the coating layers was compared with that of titanium. The chemical compositions of the nitrogen ion implanted and nitride coated layers were examined with a scanting auger electron spectroscopy. It wat observed that the metal ions released from the nitrogen ion implanted S.S.S surface were significantly reduced. From the results obtained, it was shown that the nitrogen ion implanted zone obtained with 100 KeV ion energy was easily removed within 200,000 revolutions from a wear dissolution testing under a similar load condition when applied to artificial hip joint. The remarkable improvement in wear resistance weir confirmed by the nitrides coated Ti materials and the wear properties differ greatly according to the chemical composition of the coating layers. for specimens with the same coating thickness of about 3$\mu\textrm{m}$, TiCN coated Ti showed the highest wear resistance. However, after removing the coating layers, the wear rates of all nitrides coated Ti reverted to their normal rates of below 10,000 revolutions from Ti-disk-on-disk wear testing under the same load condition. From the results obtained, it is suggested that the insufficient depth of the 100 Kel N$\^$＋/ ion implanted zone and of the nitrides coated layers of 3$\mu\textrm{m}$ are subject to restriction when used as frictional parts of load bearing implants.

• Korean Journal of Materials Research
• /
• v.25 no.9
• /
• pp.442-449
• /
• 2015

The effects of coating parameters were investigated in wear resistance coatings of Diamalloy-406 on Inconel 718 to obtain an optimum coating condition by high velocity oxy-fuel spraying. The coating parameters, the flow rates of source gases (hydrogen and oxygen), the powder feed rate, and the spray distance, were designed by the Taguchi method. The optimal conditions were determined: oxygen flow rate 34 FRM, hydrogen flow rate 57 FRM, powder feed rate 35 g/min, and spray distance 7 inch. Friction coefficients of the coating and the substrate decreased with an increasing sliding surface temperature from $25^{\circ}C$ to $450^{\circ}C$. The friction coefficient of Diamalloy-4006 coating decreased as the sliding surface temperature increased from $0.43{\pm}0.01$ at $25^{\circ}C$ to $0.29{\pm}0.01$ at $450^{\circ}C$. The wear trace and wear depth of the coating were smaller than the substrate at all temperatures tested. The relationship between spray parameters and wear resistance was discussed extensively, based on the measured roughness, hardness, and porosity in each coating.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.298-304
• /
• 2009

The effect of the surface treatments on the high temperature properties of the Inconel 617, one of the promising candidate alloys for high temperature heat-transport system, has been studied. Various surface modification methods including a rapid thermal process(RTP), a hydrothermal treatment, and a physical vapor deposition($2{\mu}m$ thick TiAlN film by an arc discharge) were applied to the Inconel 617. The morphological and the structural properties of the surface-modified Inconel 617 samples after heat treatment at $1000^{\circ}C$ in the air were compared to find out whether inhomogeneous formation of $Cr_2O_3$ crust at the surface region was suppressed or not. TiAlN-coated Inconel 617 showed homogeneous microstructure and the lowest wear loss compared to bare, RTP- and hydrothermally-treated Inconel 617 by suppressing the $Cr_2O_3$ crust formation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.35-50
• /
• 2012

$900^{\circ}C$이상 초고온 He-gas 분위기 또는 용융불화염 (molten salts, FLINAK) 환경에서 사용될 VHTR(Very High Temperature Reactor)의 IHX(Intermediate heat exchanger)용 열수송 구조재료로 가장 가능성이 높은 합금인 Inconel 617 및 Hastelloy X 상에 습식화학적, 물리적기상합성법(Vacuum arc-plasma과 RF magnetron sputtering) 및 pack cementation에 의한 표면개질 및 마이크로 초내열(refractory ceramics) 코팅층(TiN, TiCN, TiAlN, $Al_2O_3$, $TiO_2$)을 형성시켰다. 고온 장기사용 시 문제가 될 수 있는 고온에서의 조직변화, 미세구조와 상(phase)형성, 고온 부식 및 그에 따른 마모(wear resistance) 손상 등 이들 소재의 내열, 내식 및 내마모 물성을 개선하는 연구를 수행하였다. TiAlN 박막의 경우 공기분위기에서 N이 분해되나 치밀한 산화물($TiO_2/Al_2O_3$ layer)을 형성하여 내식성 있는 보호피막을 형성함으로 기판과의 열팽창 계수로 인한 박리가 발생하지 않아 보호피막으로 적합하였다. Pack cementation법에 의한 aluminiding(Al-Ni합금)도 He 및 공기분위기에서 고온물성의 저하를 가져오는 $Cr_2O_3$의 생성을 충분히 억제하고 있었으며 He 및 air 분위기에서 사용이 가능한 박막으로 여겨진다. 내열 및 내식성에 대한 실험을 종합한 결과, 공기분위기에서 사용할 수 없는 박막은 He-gas 및 FLINAK(LiF-NaF-KF) 용융염 분위기에서도 사용할 수 없었으며, He-gas, FLINAK 및 air 분위기에서 모두 사용이 가능한 박막으로는 Inconel 617에서는 $(TiO_2-)Al_2O_3$, TiAlN 및 Al-Ni이었고 Hastelloy에서는 Al-Ni 및 $Al_2O_3$가 가장 적당하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.155-155
• /
• 2016

DLC (Diamond like Carbon)는 Diamond와 유사한 물리화학적 특성을 보유한 막으로 고경도 및 우수한 내마모성, 화학적 안정성의 특성을 가지고 있다. DLC는 크게 카본의 막 형성 공정에서 카본 소스에 따라 수소가 포함된 DLC와 무수소 DLC 로 구분된다. Tetrahedral amorphous carbon (ta-C) 박막은 DLC 박막 중에서 가장 다이아몬드와 유사한 특성을 가지는 박막으로, a:C-H에 비해 고온안정성, 높은 경도 (30~80 GPa) 및 내마모 특성이 우수하여, 현재 다양한 응용분야에 적용되고 있으며, 최근에는 고내구성을 보유하면서 전기적 특성을 가지는 기능성 DLC막의 요구가 증대하고 있다. 본 연구에서는 무수소 DLC 형성을 위해 자장필터가 장착된 Filtered Vacuum Arc Source (FVAS)를 자체적으로 개발하여 연구를 수행하였다. FVAS 장비는 카본 이온 발생부와 Plasma Duct 부위, 전자석부위 구성되어 있으며, 본 연구에서는 Plasma Duct 부위의 Bias 제어를 통한 음극에서 기판으로 이동하는 카본이온의 에너지 및 flux 변화를 통해 ta-C 막의 전기적, 기계적 물성 연구를 진행하였다. Plasma Duct Bias 변화는 각 0 ~ 20 V 조건으로 진행하였으며, 물성 평가는 경도 (Hardness), 마찰계수, 전기적 특성에 대한 분석을 진행하였다. 박막의 증착 거동에서는 Plasma Duct bias 변화에 따라 10 V에서 가장 높은 증착 거동을 가지다 감소하는 경향을 확인 하였으며, 박막의 물성 특성 평가 시에도 이와 유사하게 특성의 차이를 관찰하였다. 이는 음극부위에서 형성된 카본이온이 기판에 도달 시에 Plasma Duct Bias 변화에 따라 이온의 Flux 및 에너지 변화로 인한 박막의 밀도 및 ta-C 막의 물성 변화로 예상되며, 이를 분석하기 위해 라만 분석법을 통해 증명하였다.