• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.19-24
• /
• 2020

In this work, the electrical property of Si-doped β-Ga2O3 was investigated via a post-growth annealing process. The Ga2O3 samples were annealed under air (O-rich) or N2 (O-deficient) ambient at 800~1,200℃ for 30 mins. There was no correlation between the crystalline quality and the electrical conductivity of the films within the experimental conditions explored in this work. However, it was observed the air ambient led to severe degradation of the film's electrical conductivity while N2-annealed samples exhibited improvement in both the carrier concentration and Hall mobility measured at room temperature. Interestingly, the x-ray photoemission spectroscopy (XPS) revealed that both annealing conditions resulted in higher concentration of oxygen vacancy (VO). Although it was a slight increase for the air-annealed sample, high resistivity of the film strongly suggests that VO cannot be a shallow donor in β-Ga2O3. Therefore, the enhancement of the electrical conductivity of N2-annealed samples must be originated from something other than VO. One possibility is the activation of Si. The XPS analysis of N2-annealed samples showed increasing relative peak area of Si 2p associated with SiOx with increasing annealing temperature from 800 to 1,200℃. However, it was unclear whether or not this SiOx was responsible for the improvement as the electrical conductivity quickly degraded above 1,000℃ even under N2 ambient. Furthermore, XPS suggested the concentration of Si actually increased near the surface as opposed to the shift of the binding energy of Si from its initial chemical state to SiOx state. This study illustrates the electrical changes induced by a post-growth thermal annealing process can be utilized to probe the chemical and electrical states of vacancies and dopants for better understanding of the electrical property of Si-doped β-Ga2O3.

• Cartoon and Animation Studies
• /
• s.33
• /
• pp.317-341
• /
• 2013

Found Footage Film has been increasingly addressed between film and visual art world in the age of rapid media change. With regards to this self-conscious found footage filmmaking, narrative structures are unraveled to relate new stories, images are removed from their original context only to reappear in a different context, new layers that alter the meaning are added, stereotypes from Hollywood movies are exposed, and new montages are used to destroy the illusion of the medium itself. The physical properties of the original material are also emphasized or altered in order to add a new meaning. The starting point of this study is the recognition of the origin of found footage film. It traces back to the found object from primitive impulse and found art from Dada and surrealism. Many found footage films have been at least partly inspired by Duchamp's ready-mades. These films use footages that the filmmakers did not shot, and even footage that was never intended as art. This essay deals with the found footage practices and interrogates the aesthetic implications by the concept of self-reflexivity. Self-reflexivity means consciousness turning back on itself, and found footage film is about films which call attention to themselves as cinematic constructs. It breaks with art as illusionism and exposes their own factitiousness as textual constructs. Furthermore, the inevitable mortality of celluloid and temporal reconstruction of original film will be treated. Recentely, many attention has been given to role of Found Footage Film. I hope to add the understanding of the artistic found footage film with this study.

• Journal of the Korean Chemical Society
• /
• v.51 no.2
• /
• pp.178-185
• /
• 2007

Intermediate pentasil borosilicate zeolite-like materials have been crystallized by a novel method named steam-assisted conversion, which involves vapor-phase transport of water. Indeed, amorphous powders obtained by drying Na2O.SiO2.B2O3.TBA2O gels of various compositions using different boron sources are transformed into crystalline borosilicate zeolite belonging to pentasil family structure by contact with vapors of water under hydrothermal conditions. Using a variant of this method, a new material which has an intermediate structure of MFI/MEL in the ratio 90:10 was crystallized. The results show that steam and sufficiently high pH in the reacting hydrous solid are necessary for the crystallization to proceed. Characterization of the products shows some specific structural aspects which may have its unique catalytic properties. X-ray diffraction patterns of these microporous crystalline borosilicates are subjected to investigation, then, it is shown that the product structure has good crystallinity and is interpreted in terms of regular stacking of pentasil layers correlated by inversion centers (MFI structure) but interrupted by faults consisting of mirror-related layers (MEL structure). The products are also characterized by nitrogen adsorption at 77 K that shows higher microporous volume (0.160 cc/g) than that of pure MFI phase (0.119 cc/g). The obtained materials revealed high surface area (~600 m2/g). The infrared spectrum reveals the presence of an absorption band at 900.75 cm-1 indicating the incorporation of boron in tetrahedral sites in the silicate matrix of the crystalline phase.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.6
• /
• pp.237-241
• /
• 2008

Hot-press sintering of AlN ceramics were carried out with $Y_2O_3$ as sintering additive at a sintering temperature $1,750{\sim}1,850^{\circ}C$. The effect of $Y_2O_3$ addition and sintering time on sintering behavior and thermal conductivity of AlN ceramics was investigated. $Y_2O_3$ added AlN showed noticeably higher denazification rate than pure AlN. The thermal conductivity of AlN specimens was promoted by the addition of $Y_2O_3$ in spite of the formation of YAG secondary phase in AlN grain boundaries and grain boundary triple junction because $Y_2O_3$ addition could reduced the oxygen contents in AlN lattice which is primary factor of thermal conductivity. Typically, the thermal conductivity of 5 wt% $Y_2O_3$ added specimen was dramatically improved by the increase of sintering time because the elimination of YAG secondary phases from the grain boundary due to the evaporation, as well as the grain-growth of AlN grains.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.4
• /
• pp.152-158
• /
• 2018

PVT (Physical Vapor Transport) method has advantages in producing high quality, large scale wafers where many researches are being carried out to commercialize nitride semiconductors. However, complex process variables cause various defects when it had non-equilibrium growth conditions. Annealing process after crystal growth has been widely used to enhance the crystallinity. It is important to set appropriate temperature, pressure, and annealing time to improve crystallinity effectively. In this study, the effect of the annealing conditions on the crystalline structure variation of the AlN single crystal grown by PVT method was investigated with synchrotron whitebeam X-ray topography, electron backscattered diffraction (EBSD), and Rietveld refinement. X-ray topography analysis showed secondary phases, sub-grains, impurities including carbon inclusion in the single crystal before annealing. EBSD analyses identified that sub-grains with slightly tilted basal plane appeared and the overall number of grains increased after the annealing process. Rietveld refinement showed that the stress caused by the temperature gradient during the annealing process between top and bottom in the hot zone not only causes distortion of grains but also changes the lattice constant.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.214.1-214.1
• /
• 2015

Thin-film transistors (TFTs)의 채널층으로 널리 쓰이는 indium-gallium-zinc oxide (IGZO)는 높은 전자 이동도(약 10 cm2/Vs)를 나타내며 유기 발광 다이오드디스플레이(OLED)와 대면적 액정 디스플레이(LCD)에 필수적으로 사용되고 있다. 하지만, 이러한 재료는 우수한 TFT의 채널층의 특성을 가지는 반면, ZnO 기반 재료이기 때문에 소자 구동에서의 안정성은 가장 큰 문제로 남아있다. 따라서 최근, IGZO layer의 특성을 향상시키기 위한 연구가 다양한 방법으로 시도되고 있다. IGZO의 조성비를 조절하여 전기적 특성을 최적화거나 IGZO layer의 조성 중 Ga을 다른 금속 메탈로 대체하는 연구도 이루어지고 있다. 그러나 IGZO에 미량의 도펀트를 첨가하여 박막 특성 변화를 관찰한 연구는 거의 진행되지 않고 있다. 산화물 TFTs의 전기적 특성과 안정성은 산소 함량에 영향을 많이 받는 것으로 알려져 있으며, 더욱이 TFT 채널층으로 쓰이는 IGZO 박막의 고유한 산소 공공은 디바이스 작동 중 열적으로 활성화 되어 이온화 상태가 될 때 소자의 안정성을 저하시키는 것이 문제점으로 지적되고 있다. 그러므로 본 연구에서는 낮은 전기 음성도(1.22)와 표준전극전위(-2.372 V)를 가지며 산소와의 높은 본드 엔탈피 값(719.6 kJ/mol)을 가짐으로써 산소 공공생성을 억제할 것으로 기대되는 yttrium을 IGZO의 도펀트로 도입하였다. 따라서 본 연구에서는 Y-IGZO의 박막 특성 변화를 관찰하고자 한다. 본 연구에서는 magnetron co-sputtering법으로 IGZO 타깃(DC)과 Y2O3 타깃(RF)를 이용하여 기판 가열 없이 동시 방전을 이용해 non-alkali glass 기판 위에 증착 하였다. IGZO 타깃은 DC power 110 W으로 고정하였으며 Y2O3 타깃에는 RF Power를 50 W에서 110 W까지 증가시키면서 Y 도핑량을 조절하였다. Working pressure는 고 순도 Ar을 20 sccm 주입하여 0.7 Pa로 고정하였다. 모든 실험은 $50{\times}50mm$ 기판 위에 총 두께 $50nm{\pm}2$ 박막을 증착 하였으며, 그 함량에 따른 전기적 특성 및 광학적 특성을 살펴보았다. 또한, IGZO 박막 제조 시 박막의 안정화를 위해 열처리과정은 필수적이다. 하지만 본 연구에서는 열처리를 진행하지 않고 Y-IGZO의 안정성 개선 여부를 보기 위하여 20일 동안 상온에서 방치하여 그 전기적 특성변화를 관찰하였다. 나아가 Y-IGZO 채널 층을 갖는 TFT 소자를 제조하여 소자 구동 특성을 관찰 하였다. Y2O3 타깃에 가해지는 RF Power가 70 W 일 때 Y-IGZO박막은 IGZO박막과 비교하여 상대적으로 캐리어 밀도는 낮은 반면 이동도는 높은 최적 특성을 얻을 수 있었다. 상온방치 결과 Y-IGZO박막은 IGZO박막에 비해 전기적 특성 변화 폭이 적었으며 이것은 Y 도펀트에 의한 안정성 개선의 결과로 예상된다. 투과도는 Y 도핑에 의하여 약 1.6 % 정도 상승하였으며 밴드 갭 내에서 결함 준위로 작용하는 산소공공의 억제로 인한 결과로 판단된다.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.57-64
• /
• 2006

The crack presented in concrete structures causes a structural defect, the durability decrease, and external damages etc. Therefore, it is necessary to improve durability through the effort to control the crack. Fluosilicic acid($H_2SiF_6$) is recovered as aqueous solution which absorbs $SiF_4$ produced from the manufacturing of industrial-graded $H_3PO_4$ or HF. Generally, fluosilicates prepared by the reaction between $H_2SiF_6$ and metal salts. Addition of fluosilicates to cement endows odd properties through unique chemical reaction with the fresh and hardened cement. Mix proportions for experiment were modulated at 0.45 of water to cement ratio and $0.0{\sim}2.0%$ of adding ratio of fluosilicate salt based inorganic compound. To evaluate correlation of concrete strength and adding ratio of fluosilicate salt based inorganic compound, the tests were performed about design strength(21, 24, 27 MPa) with 0.5% of adding ratio of fluosilicate salt based inorganic compound. Applications of fluosilicate salt based inorganic compound to reduce cracks resulted from plastic and drying shrinkage, to improve durability are presented in this paper. Durability was evaluated as neutralization, chloride ion penetration depth, freezing thawing resistant tests and weight loss according reinforcement corrosion. It is ascertained that the concrete added fluosilicate salt based inorganic compound showed m ability to reduce the total area and maximum crack width significantly as compared non-added concrete. In addition, the durability of concrete improved because of resistance to crack and watertightness by packing role of fluosilicate salt based inorganic compound obtained and pozzolanic reaction of soluble $SiO_2$ than non-added concrete.

• Clinical and Experimental Reproductive Medicine
• /
• v.30 no.1
• /
• pp.15-21
• /
• 2003

Objective : Clomiphene citrate is one of the most commonly used drugs in the treatment of infertility, but the pregnancy rate achieved with clomiphene citrate is significantly lower than the ovulation rate due to its antiestrogenic effect on the endometrium. Endometrial prolactin is considered to be a marker and an inducer of predecidualization that is characteristic of secretory endometrium. The purpose of this study was to evaluate the association of clomiphene citrate and unsatisfactory endometrial differentiation to secretory endometrium by examining the endometrial expression of prolactin in clomiphene citratetreated infertile women with luteal phase defect. Methods : The endometrial samples from infertile women with luteal phase defect (n=27) were examined. Five cases during secretory phase and six cases during proliferative phase were obtained by biopsy. Sixteen cases were obtained by biopsy during secretory phase after clomiphene citrate treatment. By immunohistochemical staining for prolactin, all obtained endometrial tissues were examined. The differences in the endometrial expression of prolactin were evaluated between proliferative phase and secretory phase, and between clomiphene citrate treated group and no treatment group during secretory phase. Results: The staining of endometrial prolactin was significantly more intense in the glandular epithelial cells and stromal cells in the secretory endometrium than in the proliferative endometrium. The glandular expression of prolactin in the secretory endometrium was not significantly different between the clomiphene citrate-treated group and no treatment group (p=0.719), but the staining of prolactin in the stromal cells was significantly less intense in the clomiphene citrate-treated group than no treatment group (p=0.019). Conclusion: In this investigation, we demonstrated that the endometrial stromal expression of prolactin in the secretory phase was significantly lower in the clomiphene citrate-treated group campared with no treatment group in infertile women with luteal phase defect. And our finding suggests that clomiphene citrate may have an adverse effect on the endometrial predecidualization in infertile women.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.511-520
• /
• 2007

There is a concern with worldwide deterioration of highway bridges, particularly reinforced concrete. The advantages of fibre reinforced plastic(FRP) composites over conventional materials motivate their use in highway bridges for replacement of structures. Recently, an FRP deck has been installed on a state highway, located in New York State, as an experimental project. In this paper, a systematic approach for analysis of this FRP deck bridge is presented. Multi-step linear numerical analyses have been performed using the finite element method to study the structural behavior and the possible failure mechanism of the FRP deck-superstructure system. Deck's self-weight and ply orientations at the interface between steel girders and FRP deck are considered in this study. From this research, the results of the numerical analyses were corroborated with field test results. Analytical results reveal several potential failure mechanism for the FRP deck and truss bridge system. The results presented in this study may be used to propose engineering design guideline for new and replacement FRP bridge deck structure.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.436-442
• /
• 2008

Graphite material has been recognized as a very competitive candidate for reflector, moderator, and structural material for very high temperature reactor (VHTR). Since VHTR is operated up to $900-950^{\circ}C$, small amount of impurity may accelerate the oxidation and degradation of carbon graphite, which results in increased porosity and lowered fracture toughness. In this study, ultrasonic wave propagation properties were investigated for both as-received and degradated material, and the feasibility of ultrasonic testing (UT) was estimated based on the result of ultrasonic property measurements. The ultrasonic properties of carbon graphite were half, more than 5 times, and 1/3 for velocity, attenuation, and signal-to-noise (S/N) ratio respectively. Degradation reduces the ultrasonic velocity slightly by 100 m/s, however the attenuation is about 2 times of as-receive state. The results of probability of detection (POD) estimation based on S/N ratio for side-drilled-hole (SDHs) of which depths were less than 100 mm were merely affected by oxidation and degradation. This result suggests that UT would be reliable method for nondestructive testing of carbon graphite material of which thickness is not over 100 mm. In accordance with the result produced by commercial automated ultrasonic testing (AUT) system, human error of ultrasonic testing is barely expected for the material of which thickness is not over 80 mm.