• Journal of Wind Energy
• /
• v.9 no.4
• /
• pp.24-31
• /
• 2018

Wind lidar application is increasing and its calibration method is required to use wind lidar as an alternative to the meteorological mast. A nacelle lidar calibration method is now being discussed in IEC 61400-50-3 (Wind energy generation systems - Part 50-3: Use of nacelle-mounted lidars for wind measurements), and the method is mainly based on the wind lidar beam line of sight (LOS) wind speed calibration suggested by DTU as DTU E-0020 (Calibrating Nacelle Lidars). In this paper, a LOS wind speed calibration method is introduced and a calibration example performed on Jeju island is presented. The results showed a slope of 1.011 and R2 of 0.997, which means that the LOS wind speed is highly correlated with the reference wind speed and is comparable. But LOS wind speed calibration requires a very long time due to its principle and environmental conditions, and a calibration method that can overcome this problem of uncontrollable environments needs to be developed.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.65-72
• /
• 2012

Numerical simulations were performed to study the stall characteristics of turboprop aircraft. Stall characteristics were qualitatively investigated using the computational results of various configurations based on the combinations of propeller and high lift device. For the analysis of stall characteristics, three-dimensional Navier-Stokes solver with Spalart-Allmaras turbulence model was used and the relative motion between propeller and wing was simulated using sliding mesh technique. For the cruise configurations, major flow separation was occurred at the fuselage/wing fairing and the separation was reduced under propeller slipstream condition. For the high lift device configuration without propeller, major flow separation was occurred at the outboard side of nacelle. With rotating propeller, early stall onset due to low relative velocity and high effective angle of attack was observed on the outboard wing section. Regarding rotating direction of propeller, inboard-down direction was preferred due to the stall delay effect of propeller slipstream.

• Journal of the Society of Disaster Information
• /
• v.10 no.2
• /
• pp.244-252
• /
• 2014

In this study, seismic responses of the offshore wind tower supported by bucket foundation are analyzed in consideration of soil-structure interaction. The program SASSI is used as analyzing tool and an artificial seismic input for soft soil is used as input motion. The H/R ratio of bucket, the stiffness of bucket foundation and the soil stiffness are considered as parameters and its effects are estimated. The responses of structure are obtained at the base and the nacell. As results, the effects of H/R ratio, the stiffness of bucket and the stiffness of site are generally denoted different response tendency at the base and the nacell. However, these whole responses of the base and the nacell are much lager than that of rock site. Therefore, the consideration of this phemomia affect to the response of offshore wind tower with bucket foundation largely.

• Journal of computational fluids engineering
• /
• v.6 no.2
• /
• pp.1-8
• /
• 2001

Despite the massive effort which has been given to the analysis of the base flows, one commonly occurring case seems to be overlooked. This is for base (rearward facing surface) which is between a subsonic flow and supersonic flow. Potential flows of the air and gas streams are computed for the flow past a separated wake. Then a viscous jet mixing is superimposed on this inviscid solution. Conservation of mass, momentum and energy is achieved by multiple iterations. Despite the iterations, the wake flow field is computed with modest computer requirements.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.55-58
• /
• 2005

풍력발전기에 있어서 보호 및 제어 시스템은 그 효율, 성능, 안전 및 수명까지도 영향을 미칠 수 있는 중요한 구성요소이다 따라서 제어 시스템은 풍력발전기의 최대 효율 및 가동률을 확보하여야 하며 풍력발전기에 문제가 발생할 경우 즉시 가동을 정지할 수 있도록 안전성을 확보할 수 있도록 설계되어야 한다. 본 연구에서는 "750kw급 Gearless형 풍력발전시스템 개발" 과제의 일환으로 수행되었던 풍력발전기용 제어시스템의 설계 및 제작 과정과 상용제품으로서의 본 제어 시스템을 소개하고자 한다.

• Journal of the Korean Society of Safety
• /
• v.25 no.4
• /
• pp.1-6
• /
• 2010

Wind power system is composed by 3 major parts, rotor blade, nacelle and tower. Especially, the nacelle cover has an important role to prevent the component of nacelle and rotor from an extreme external circumstance. Therefore it is necessary to analyze and evaluate the stress distribution and deformation for them in the design level. There are two major points in nacelle cover analysis. The one is nacelle cover itself and the other is cover support structure. According to GL specification, this study shows the result that CFRP nacelle cover of wind turbine satisfies the strength and deformation through numerical analysis using the commercial finite element analysis program.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.295-298
• /
• 2008

The major function of the nacelle cover is protecting the inside equipments. Therefore, it is required not only sufficient strength and stability but also light weight. In this paper, design loads are calculated according to the GL Wind guideline Ed. 2003. To ensure the structural safety, a composite structure is selected. The structural design is processed by two steps which are preliminary design and detail design. In the preliminary design step, a structural analysis is performed with initial thickness, 5mm. As reviewing above analysis results, weak regions of the nacelle cover reinforced using the spar cap structure which is same as the blade structure. In the analysis model, the support structure is connected with the nacelle cover and analyzed its structural safety at the same time.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.10
• /
• pp.810-815
• /
• 2008

To enhance aerodynamic efficiency of the Smart Un-manned Aerial Vehicle(SUAV) during the transition period, wingtip fence is attached at the end of wing. The application of wingtip fence is to reduce the effect of the separated flow caused by the nacelle on the wing especially when the tilting angle of nacelle is more than 30 degrees. To compare the effect of with and without wingtip fence, flow visualization and measurement of the aerodynamic coefficients using the pyramidal type external balance are done. Result of forces and moments measurement shows that the slope of lift coefficient is increased 18% and rolling moment of SUAV especially 60 & 90-degree tilting is changed in favorable manners with wingtip fence.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.11a
• /
• pp.167-173
• /
• 1999

An Euler-based CFD tool has been developed for the performance evaluation of a thrust reverser mounted on a high bypass ratio turbofan engine. The computational domain surrounded by the ground and non-reflection boundary includes the whole nacelle configuration with a deployed thrust reverser. The numerical algorithm is based on the modified Godunovs scheme to allow the second order accuracy in both space and time. The grid system is generated by using eleven multi-blocks, of which the total cell number is 148,400. The thrust reverser is modeled as if it locates at the nacelle simply in all circumferential direction. The existence of a fan and an OGV(Outlet Guide Vane) is simulated by adopting the actuator disk concept, in which predetermined radial distributions of stagnation pressure ratio and adiabatic efficiency coefficient are used for the rotor type disk, and stagnation pressure losses and flow outlet angles for the stator type disk. All boundary conditions including the fan and OGV simulation are treated by Riemann solver. The developed solver is applied to a turbofan engine with a bypass ratio of about 5.7 and the diameter of the fan cowl of 83 inch. The computational results show that the Euler-based inviscid method is very useful and economical to evaluate the performance of thrust reversers.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.67-70
• /
• 2007

It is well known that the aircraft engine inlet should be safely designed against the bird strike at the aircraft development stage. The aircraft accident is increasing for FOD(Foreign Object Damage), especially bird of runway circumference. The aircraft accident due to bird strike brings about economic loss and which is connected with the life of passengers. In this study, MSC/DYTRAN has been utilized to analyze the aircraft engine inlet against the bird strike. In order to validate the proposed method for the bird strike analysis, this study was performed with comparison of precedence study results.