• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2091-2096
• /
• 2007

This paper presents a mathematical model for predicting the frost behavior formed on heat exchanger fins, considering fin heat conduction under frosting condition. The model is composed of air-side, the frost layer, and fin region, and they are coupled to the frost layer. The frost behavior is more accurately predicted with fin heat conduction considered (Case A) than with a constant fin surface temperature assumed (Case B). The results indicate that the frost thickness and heat transfer rate for Case B are over-predicted in most regions of the fin, as compared to those for Case A. Also, for Case A, the maximum frost thickness varies little with the fin length variations, and the extension of the fin length over 30 mm contributes insignificantly to heat transfer.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3128-3133
• /
• 2007

The mixing method of water and chemicals is significant in a small-scale water supply system because drinking water should be supplied with a certain quantity of remaining chemicals maintained. In the present study, the concentration distribution and the mixing index were obtained from four models, which were to find out the optimal mixing method of water and chemicals. The two models brought the good mixing effects out of the four, one for providing chemicals from the center of water supply pipe and the other for setting up the semicircle block at the downstream of the chemicals-providing pipe. As a result, the mixing effect was found out to be increased due to the diffusion and the disturbance of flows. In conclusion, these results are expected to contribute to designing the optimal mixing system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2857-2861
• /
• 2007

Flow and aerodynamic characteristics were analyzed numerically for a commercial passenger airplane, Boeing 747-400, flying in the cruising condition. The model geometry with 100:1 in scale was obtained by the photo scanning measurement with the maximum error of 1.4% comparing with the real airplane dimension. The three-dimensional inviscid steady compressible governing equations were solved by the finite volume method in the unstructured grid system. The convective terms were treated by the Crank-Nicholson and first-order upwind schemes. In the computational results, the strong wing-tip vortices were clearly observed and the pressure contours on the airplane surface were suggested. The lift and drag forces in the wing with engines increase by 1.49% and 3.9%, respectively compared with the case without engines. The aerodynamic forces were estimated quantitatively for each element which consists of the airplane.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1223-1225
• /
• 1995

The $NO_2$ gas-detection characteristics were investigated using the functional organic Langmuir-Blodgett(LB) films of Copper-tetra-tert-butylphthalocyanine(CuTBP). The optimum conditions for a film deposition were obtained through a study of $\pi$-A isotherms, and the deposited film status was confirmed by the ellipsometry measurements. The $NO_2$ gas response experiments under 200 ppm concentration at room temperature show that there are increment of electrical conductivity by 40 times and 25 seconds of response time, and 40 seconds of recovery times.

• 제어로봇시스템학회논문지
• /
• 제18권7호
• /
• pp.622-626
• /
• 2012

This paper presents synchronization of LTV (Linear Time-Varying) MAS (Multi-Agent Systems) with heterogeneous time-varying disturbances under a fixed, connected, and undirected communication network. All the agents can collect only relative state information from their neighborhoods. To achieve synchronization of the MAS, an integral control scheme is proposed based on relative state information between agents.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 추계학술대회 논문집
• /
• pp.124-129
• /
• 2010

Wind load characteristics is investigated for vibration analysis of wind turbine gearbox. A normal wind model assumed, of which the wind velocity is increased according to the height from ground. A blast wind model is assumed, of which the maximum velocity is located at the center and the velocity profile is normally distributed. The periodical torque and bending moments transmitted to the main shaft of wind turbine are investigated. The average values and the harmonic terms of the transmitted moments are studied on the wind direction of range $-45^{\circ}{\sim}45^{\circ}$ and the bending moment characteristics are examined, which is regarded as the main source of the misalignment of gear train.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.415-415
• /
• 2012

ICP (RF) 열 플라즈마 분말 합성법은 초고온 열플라즈마(~10,000 K) 속으로 원료물질을 투입한 뒤, 용융, 기화 및 재합성의 과정을 거쳐 초미분(<1 ${\mu}s$)을 합성하는 방법으로 고출력 시스템의 경우 고온/고 엔탈피 열 유동을 통한 고융점 및 저융점 복합물질의 동시 기화에 의한 물질 조성이 제어된 나노 복합체의 대량 합성이 가능할 것으로 기대되고 있다. 본 연구에서는 전북대학교 고온플라즈마 응용연구센터의 60&200 kW의 고출력 ICP (RF) 열 플라즈마 시스템을 이용하여 LTO (Lithium Titanium Oxide)와 IZTO (Indium Zinc Tin Oxide), Barium Borosilicate Glass (K2O-BaO-B2O3-SiO2)의 다성분계 나노 복합체를 합성하였으며, FE-SEM, TEM, XRD, ICP-OES를 이용하여 그 특성을 분석하였다.

• 제어로봇시스템학회논문지
• /
• 제19권3호
• /
• pp.177-182
• /
• 2013

This paper proposes an input-constrained reference tracking control of a converter model. To this end, first it is shown that the bilinear converter model can be equivalently represented by a linear uncertain model belonging to a polytopic set. Then, an input-constrained tracking control scheme for the linear uncertain model is designed based on recently proposed tracking control scheme. The control scheme yields not only a stabilizing control gain but also a feasible and invariant set for the converter model. Finally, simulation results show that the state trajectory always stays in the feasible and invariant set and that the output tracks the given reference while satisfying the input constraint.

• 한국정밀공학회지
• /
• 제30권6호
• /
• pp.584-588
• /
• 2013

Studies are using a roll forming bar. A bar coating device available for a variety of coating conditions was developed. It is characterized by the bar forward and reverse rotation, fine-tune coating speed, and stripe coating. To determine the characteristics of the equipment, the coating tests under different coating conditions were carried out. As a result of the coating tests, the equipment was confirmed as one of strong candidates for the production tool of organic solar cells. The further production test of organic solar cells through stripe coating is in progress.

• 제어로봇시스템학회논문지
• /
• 제20권12호
• /
• pp.1231-1237
• /
• 2014

본 논문에서는 축소 차수 외란 관측기를 이용하여 외란이 있는 이종 다개체 시스템을 위한 협조 추종 제어기를 제안하였다. 이를 위해 우선 주어진 제어 문제가 외란과 모델 불확실성을 가지는 시스템을 위한 강인 제어 문제로 변환 될 수 있음을 보이고 변환된 문제에 외란 관측기 기반의 동적 협조 추종 제어기를 설계하였다. 모의 실험을 통해서 제안하는 이종 다개체 시스템의 협조 추종을 성공적으로 달성함을 보였다.