• Laser Solutions
• /
• v.1 no.1
• /
• pp.18-23
• /
• 1998

A Study on microstructural changes of sensitized Alloy 600 which was rapidly solidified by a $CO_2$ laser beam was conducted using microscopic equipments such as SEM and TEM. Dissolution of Cr-rich carbides and resultant Cr recovery on the grain boundaries occurred in the heat affected zone (HZA). The microstructure of the laser melted zone (LMZ) having epitaxially solidified from the HAZ was mainly celluar-dendritic with the 〈100〉 crystallographic direction of growth. The Cr concentration was observed to increase along the cell bondaries, and tiny particles were distributed along the cell walls with tangled dislocations around them. Cr-rich carbides had been completely melted by the high density of a laser beam, and were not re-precipitated during the matrix solidification due to a fast cooling rate in the LMZ.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2073-2080
• /
• 1994

In this paper, a model of material removal in abrasive water jet machining of brittle material is developed, and experimentally evaluated. Abrasive water jet machining proved to yield better material removal rate than other machining techniques for hard and brittle material (alumina ceramics). It was also found that large scale fracture may develop at the exit of the jet from the material. The fracture size was predicted as a function of water jet pressure and size of the hole. Finally, the feasibility of using acoustic emission signals for in-process monitoring of the abrasive water jet machining process is investigated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.1
• /
• pp.117-124
• /
• 2003

Thermal design fur satellite propulsion system has been performed. Overall design requirements and the constitution for propulsion system is described. To meet the thermal design requirements, both a primary and a redundant heater circuit, each with two thermostats placed in series, will protect each hydrazine-wetted components, even if one heater circuit fails to operate. Heater power is turned off if any one of these thermostats is opened at its higher setpoint. Thus, even if one thermostat is failed closed, the second thermostat will turn off the heater. All such components shall be insulated with MLI. Propulsion heater sizing based on the constant worst cold case condition is conducted through thermal analysis. All heaters selected fur propulsion components operate to prevent propellant freezing satisfying the thermal requirements for the propulsion subsystem over the worst case average voltage, i.e. 25 volts.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1251-1255
• /
• 2006

도로 조건에 따른 빗물받이 유입구의 설치간격, 적정크기 및 관리 방안을 마련하여야 하며, 빗물받이 설계 시, 빗물받이 유입구의 통수능력을 저하시키는 빗물받이 유입구의 막힘 현상을 고려한 빗물받이 유입구의 합리적인 설계와 관리 방안을 마련하여 빗물 배제 능력을 향상시킴으로써 도시 홍수피해의 경감대책을 수립하여야 한다. 따라서 본 연구에서는 합리식을 이용하여 우수유출량을 계산하고, 빗물받이 차집효율 실험을 통하여 산정된 빗물받이 규격별 차집유입량 경험식을 이용하여 빗물받이의 차집유입량을 산정하였다. 막힘 현상을 고려한 빗물받이 유입구의 찻집효율 분석 실험을 실시하여 제시되어진 막힘 계수를 이용하여 빗물받이 유입구의 막힘 현상을 고려한 도로의 격자형 빗물받이 유입구의 설계 방법을 제시하였으며, Excel을 이용하여 간략하게 프로그램화 하였다. 제시된 설계방법은 실무에서 도로 조건의 변화와 빗물받이의 막힘 현상을 고려한 빗물받이 유입부의 설계에 사용 가능하다고 판단된다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.84-89
• /
• 1998

Alloy 600 및 alloy 690과 Ni-8Cr-lOFe 합금 등의 응력부식(stress corrosion cracking, SCC) 거동을 고온의 염기성 분위기에서 C-ring 시편을 사용하여 연구하였다. Alloy 600과 alloy 690을 여러 조건에서 열처리하여 etching한 후 탄화물의 분포와 입계 주변의 Cr고갈 정도 등의 미세조직을 광학현미경과 주사 전자현미경(SEM)으로 관찰하였다. 이들 재료에 대한 SCC 시험을 315$^{\circ}C$의 40% NaOH 수용액에서 일정한 부하전위(부식전위 + 200㎷)를 가하면서 수행하였으며, 동일 조건에서의 분극거동도 측정하였다. Alloy 600 MA(mill anneal) 및 TT(thermal treatment)의 SCC 저항성은 alloy 690 TT와 Ni-8Cr-10Fe SA(solution anneal)보다 낮았다. Alloy 600 TT 재료는 alloy 600 MA 및 SA 재료에 비해 SCC 저항성이 더 컸다. 고용 탄소농도는 alloy 600의 SCC 저항성에 큰 영향을 주지 못했다. 대부분의 Alloy 600은 균열전파 입계균열을 보였으나, 일부에서는 입계 및 입내 혼합양상(mixed mode cracking)을 보였다. 염기성 분위기에서 Ni기 합금의 SCC 거동을 미세조직, 분극거동의 관점에서 고찰하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05a
• /
• pp.193-198
• /
• 1997

본 논문의 목적은 현재 사용중인 원자력발전소내 금속파편 감시계통 (LMPS: Loose Part Monitoring System)에서 금속파편의 발생위치 평가시 온라인화된 방식을 제안하고 그 효용성을 알아보는 것이다. 현재 사용중인 LMPS들은 센서들을 통해서 기준 진폭수준 이상의 신호가 입력될 때 경보음이 울리고 신호가 기록되도록 되어있다. 이렇게 기록된 신호를 전문가가 분석함으로써 발생한 금속파편 위치 및 계통손상 가능성 등을 평가한다. 그러나 이러한 방법에 의한 신호평가시 경험이 풍부한 전문가에 의해 파편위치 및 손상부위를 평가해야 하므로 많은 시간이 소요되고 금속파편에 의한 손상 잠재성이 큰 경우 즉각적인 조치를 취할 수가 없어 방사능 누출 등의 위험한 상황에 처할 수 있다. 따라서 본 논문에서는 이러한 점에 착안하여 센서로부터의 입력신호 분석 및 평가를 위한 온라인 기법을 제안하고 구조물 모형을 이용한 실험결과를 통하여 그 효용성을 입증한다.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2006.05a
• /
• pp.202-205
• /
• 2006

• Korean Journal of Digital Imaging in Medicine
• /
• v.12 no.1
• /
• pp.9-14
• /
• 2010

Based on the cardiac PACS application collected from three university hospitals across the country, this research showed us a composition method of a server and storage devices with conditions in the field. Also, we founded the practical use of software making the best of cardiovascular PACS features. In addition, it also examined the components and requirements of the key functions that are available in the cardiovascular sector. We will be investigated the design experience and applications on stable storage and transmission of large video clip data, cardiovascular analysis, and gear interlocks through the study.

• Korean Journal of Digital Imaging in Medicine
• /
• v.12 no.1
• /
• pp.1-4
• /
• 2010

The study was designed to transmit ECG(electrocardiogram) images from iPhone in order to check validity. Especially, web examined ECG transmissions from smart phones image viewer are good enough to secure clinical information and confirmed with visual. In result, it took 3 to 5 seconds for ECG viewer transmitting from a smart phone to display an image on mobile server to user's phone. For image valuation, we magnified the ECG image 100% or 200% at a resolution of $480{\times}320$ checking PQRST wave and found that it was both possible to see an accurate PQRST wave with all the trial data and to divide it into 1mm level of grid.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1963-1970
• /
• 1993

A simple technique to decouple the modal equations of motion of a linear nonclassically damped system is to neglect the off-diagonal elements of the modal damping matrix. This is called the decoupling approximation. It has generally been conceived that smallness of off-diagonal elements relative to the diagonal ones would validate its use. In this study, the relationship between elements of the modal damping matrix and the error arising from the decoupling approximation is explored. It is shown that the enhanced diagonal dominance of the modal damping matrix need not diminish the error. In fact, the error may even increase. Moreover, the error is found to be strongly dependent on the exitation. Therefore, within the practical range of engineering applications, diagonal dominance of the modal damping matrix would not be sufficient to supress the effect of modal coupling.