• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.152-157
• /
• 2007

AlGaN/GaN high electron mobility transistors (HEMTs) were fabricated and the effect of ${N_2}O$ plasma on the electrical characteristics of the devices was investigated. The HEMT exposed to ${N_2}O$ plasma formed by 40 W of RF power in a chamber with pressure of 20 mTorr at a temperature of $200^{\circ}C$, exhibited a reduction of gate leakage current from 246 nA to 1.2 pA by 10 seconds treatment. The current between the two isolated active regions reduced from 3 uA to 7 nA and the sheet resistance of the active layer was lowered also. The variations of electrical characteristics for HEMT were occurred within a short time expose of 10 seconds and the successive expose did not influence on the improvements of gate leakage characteristics and conductivity of the active region. The reduced leakage current level was not varied by successive $SiO_2$ deposition and its removal. The transconductnace and drain current of AlGaN/GaN HEMTs were increased also by the expose to the ${N_2}O$ plasma.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.5
• /
• pp.95-102
• /
• 2010

In recent years, the demand for the development of high quality and cost effective materials, as well as the competition to ensure a diverse and sufficient amount of ready-mixed concrete, has been increasing rapidly. In this experiment, concretes made with different admixtures are blended with each other in different combinations and ratios, in order to identify potential problems. The first test was a slump level test, in which all of the concretes met the required numbers, as they also did in the test for air content. Plain organic acid concrete scored the highest in bleeding amount, but organic acid mix in general showed a similar outcome. In the early measurement of compressive strength, plain naphthalene concrete was the strongest. Of the blends, the 5:5 mix of organic acid and naphthalene was the strongest. In the standard measurement, the 5:5 mix of naphthalene and lignin was the strongest. Tensile strength tests revealed similar results. Length change rate proved to be greater in blended concrete than in plain concrete, and dry shrinkage rate was highest in the 7:3 ratio blends. Through SEM photo analysis, it was confirmed that the 7:3 ratio blends contained more micro-voids. In conclusion, with the exception of a specific few combinations, it was found that the blending of different types of concrete is undesirable due to the delayed coagulation time as well as the early decrease in strength.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.241-245
• /
• 2007

국내 홍수빈도 분포의 매개변수 추정에서 지점추정(at-site estimate) 방법은 유량 자료의 부족으로 발생하는 표본오차(sampling error)가 크기 때문에 충분한 유량 자료를 보유한 지점에 한하여 제한적으로 사용되고 있다. 대안으로 동질성을 가진 유역의 유량 자료를 모아 지역 매개변수를 추정하는 지수홍수법(Index Flood Method)이 제안되기도 하였으나, 이질성이 큰 우리나라의 유역특성 때문에 적용이 쉽지 않다. Stedinger와 Tasker가 1986년 제안한 GLS(Generalized Least Square) 기법은 유역을 동질지역으로 구분할 필요가 없으며 지점들간의 상관관계와 이분산성을 고려할 수 있어, 국내 홍수빈도 해석을 위해서 꼭 도입해야할 기법으로 생각된다. 본 연구에서는 기존의 GLS 기법의 단점을 보완한 Bayesian-GLS 기법을 이용하여, 국내 대유역에 골고루 위치하며 댐의 영향을 받지 않는 31개 지점의 연최대 일유량 시계열의 L-변동계수(L-moment coefficient variation)와 L-왜도계수(L-moment coefficient skewness)를 추정할 수 있는 회귀모형을 제안하였다. 위 회귀모형을 구성하기 위한 유역특성으로는 유역면적, 유역경사, 유역평균강우 등을 사용하였다. Bayesian-GLS (B-GLS) 적용 결과를 OLS(Ordinary Least Square) 및 Bayesian-GLS 기법에서 지점간의 상관관계를 고려하지 않는 Bayesian-WLS(Weighted Least Square)와 비교 평가하여 그 우수성을 입증하였다. 따라서 본 연구에서 제안된 B-GLS에 의한 지역회귀모형은 국내의 미계측유역이나 또는 관측 길이가 짧은 계측유역의 홍수빈도분석을 위해 매우 유용할 것으로 기대된다.년 홍수 피해가 발생하고 있지만, 다른 한편 인구밀도가 높고 1인당 가용 수자원이 상대적으로 적기 때문에 국지적 물 부족 문제를 경험하고 있다. 최근 국제적으로도 농업용수의 물 낭비 최소화와 절약 노력 및 타 분야 물 수요 증대에 대한 대응 능력 제고가 매우 중요한 과제로 부각되고 있다. 2006년 3월 멕시코에서 개최된 제4차 세계 물 포럼에서 국제 강 네트워크는 "세계 물 위기의 주범은 농경지", "농민들은 모든 물 위기 논의에서 핵심"이라고 주장하고, 전 프랑스 총리 미셀 로카르는 "...관개시설에 큰 문제점이 있고 덜 조방적 농업을 하도록 농민들을 설득해야 한다. 이는 전체 농경법을 바꾸는 문제..."(segye.com, 2006. 3. 19)라고 주장하는 등 세계 물 문제 해결을 위해서는 농업용수의 효율적 이용 관리가 중요함을 강조하였다. 본 연구는 이러한 국내외 여건 및 정책 환경 변화에 적극적으로 대처하고 물 분쟁에 따른 갈등해소 전략 수립과 효율적인 물 배분 및 이용을 위한 기초연구로서 농업용수 수리권과 관련된 법 및 제도를 분석하였다.. 삼요소의 시용 시험결과 그 적량은 10a당 질소 10kg, 인산 5kg, 및 가리 6kg 정도였으며 질소는 8kg 이상의 경우에는 분시할수록 비효가 높았으며 특히 벼의 후기 중점시비에 의하여 1수영화수와 결실율의 증대가 크게 이루어졌다. 3. 파종기와 파종량에 관한 시험결과는 공시품종선단의 파종적기는 4월 25일부터 5월 10일경까지 인데 이 기간중 일찍 파종하는 경우에 파종적량은 10a당 약 8${\ell}$이고 늦은 경우에는 12${\ell}$ 정도였다. 여기서 늦게 파종한 경우 감수의 가장 큰 원인은 1수영화수가 적어지기 때문이었다. 4. 건답직파에 대한 담수상태로 관수를 시작하는 적기는 파종후

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.112-120
• /
• 2012

A numerical model considering the internal vaporization and the creep effect, in the form of a analytical program, for tracing the behavior of high strength concrete(HSC) members exposed to fire is presented. The two stages, i.e., spalling procedure and fire resistance time, associated with the thermal, moisture flow, creep and structural analysis, for the prediction of fire resistance behavior are explained. The use of the analytical program for tracing the response of HSC member from the initial pre-loading stage to collapse, due to fire, is demonstrated. Moisture evaporates, when concrete is exposed to fire, not only at concrete surface but also at inside the concrete to adjust the equilibrium and transfer properties of moisture. Finite element method is employed to facilitate the moisture diffusion analysis for any position of member, so that the prediction method of the moisture distribution inside the concrete members at fire is developed. The validity of the numerical model used in this program is established by comparing the predictions from this program with results from others fire resistance tests. The analytical program can be used to predict the fire resistance of HSC members for any value of the significant parameters, such as load, sectional dimensions, member length, and concrete strength.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.6
• /
• pp.573-581
• /
• 1987

The fish meat paste products are rapidly growing in its production. However, the recent prohibition of AF-2 gives a lot of difficulties in the marketing of fish meat paste products manufactured ty the conventional procedures. The present study aims to obtain the optimal conditions for retaining tile quality of the fish meat paste products with long shelf-life on the market. The fried fish meat paste was sealed in the retort pouches and sterilized under the conditions which the Fo value designated to 6. The effects of the sterilization temperature and the diameter of the products on the quality factors such as jelly strength, water holding capacity, texture and in vitro protein digestibility were investigated. The jelly strength and hardness increased as the sterilization temperature increased. On the other hand, there were no differences found in water holding capacity and elasticity. Of the samples, product with diameter of 12mm showed the highest values of jelly strength, hardness, L values and in vitro protein digestibility which sterilized at $124^{\circ}C$. However. tile results of the organoleptic tests showed rather score in the products with diameter of 16 mm than 12 mm which were sterilized at $124^{\circ}C $. From the results described above, it was concluded that the fried fish meat paste products with 16 mm or less in a diameter which were sterilized at higher temperature could keep high quality.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.37-43
• /
• 2008

Inorganic injection material, which is one of the ground improvement materials, consists of cement accelerator and inorganic micro particle. The inorganic injection material is known to overcome the major limitations of water glass type improvement materials, which are leaching and accompanying strength loss. The inorganic injection material is superior in durability and strength, and environmentally friendly since leaching is prevented. In this study, the effectiveness and environment-friendliness of the MIS(Micro Injection-process System) using the inorganic injection material is compared to SGR, which uses the water glass. The performed tests were unconfined compression test, chemical resistance test, and fish poison test. The unconfined compression tests showed that the MIS results in 1.7 times higher 28 day strength compared to the SGR. In addition, the strength continually increased with time for the MIS, while it decreased for the SGR. The chemical resistance tests indicated that the rate of change in length using the MIS is 10~25 times smaller than when using the SGR. The fish poison test proved that MIS was more environmentally friendly. The analysis of chemical ingredients of leached showed that the amount of $Cr^{6+}$, Pb and Si leached from the MIS is less compared to the SGR. Accordingly, the MIS grout is more high-strength than existing SGR grout. It is excellent in shortening of construction period, structural stability of foundation and environmentally friendly. So, it is considered that it has not little the problem about groundwater pollution.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.05a
• /
• pp.11-11
• /
• 2009

종래의 산업폐수 처리기술로는 중금속 함유 폐수에 수용성의 금속염을 첨가하여 가성소다 혹은 소석회를 이용하여 pH를 조정하고 고분자 응집제를 첨가하여 금속의 수산화물을 생성시켜 이를 부상 혹은 침전시켜 Sludge화하여 제거하는 방법이 주로 사용되고 있다. 그 외 질소, 인, 유기물이 함유된 폐수의 경우에는 Biological Oxidation Techniques, 활성탄 흡착방식이 주로 채택되고 있다.[1-3] 이러한 폐수처리기술은 화학약품 사용량이 과다하고 이는 Sludge 생성량을 증대하고 2차 폐수처리가 필요로 하는 경우가 많고, 처리장이 면적이 넓어야 하고 대용량의 Sludge 제거창치가 필요하여 고비용의 처리공정으로 문제점을 가지고 있다.[2-3] 이에 본 연구에서는 이러한 기존 기술의 문제점을 보완할 수 있고 기존 기술로는 완벽하게 처리하기 곤란한 악성 폐수들에 대한 새로운 고도처리기술로 초전도 마그네트를 이용한 고구배 자기분리기술에 대한 기초연구를 하였다. 본 연구에서 사용한 고구배 자기분리 시스템은 무헬륨 전도냉각방식으로 자기분리를 위해 사용한 필터는 SUS 430 재질의 메쉬 형태로 제작하여 실험하였다. 또한, 자기분리 처리를 위한 전처리 공정으로는 응집제를 첨가하여 자기분리 효율을 높이고자 하였다. 자기분리 처리대상수로는 포항제철에 압연 강판에 사용되는 냉각수를 대상으로 자기분리 처리에 대한 효과를 실험하였다. 또한, 자기분리에 대한 특성을 평가하기 위해 강자성의 $Fe_3O_4$ 미세자성분말을 첨가하여 처리수내의 들어있는 유기물질에 대해 자기분리 자장 및 유속에 대한 처리효율을 미치는 영향을 조사하였다. 자기분리 처리는 1~6 Tesla에서 자기필터는 디스크 형태로 다층으로 연속적으로 적층하였으며, 처리유속은 1~4 l/min으로 하였다. 고농도인 처리폐수를 자가분리 인가 자장에 따라 처리하여 고농도에서는 70%, 저농도에서는 98 %까지 처리되었다. 또한, 자기분리용 필터는 SUS 430 재질의 mesh 망을 사용하였으며 인가자장 및 유속변화에 대한 실험 결과 탁도 및 농도는 필터 크기의 영향은 거의 차이가 없었으며 단지 인가자장 및 유속에 따라서 지수적으로 감소하였다. 자기분리된 용액 내 $Fe_3O_4$ 입도 분석 결과 자기분리 이전에 분포하던 $10\sim20\;{\mu}m$의 입자는 거의 제거되었으며 2 ${\mu}m$ 이하의 입자들은 실험 횟수에 따라 점점 직경이 작은 쪽으로 분포가 좁아졌으며, 마그네타이트의 자화율을 분석한 결과 약 0.8 Tesla에서 포화 되었으며 처리수의 탁도 및 농도가 자장에 따라 감소하는 것으 알 수 있었다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.128-135
• /
• 2011

In this study, in order to develop ultra rapid hardening mortar(URHM) for tunnel repairs using bottom ash of low recycle ratio and Admixture as Eco concept, fundamental properties of URHM on temperature condition of construction field were performed. Test result, URHM of three types for fluidity and setting time were as in the following : B > C > A. Those for low temperatures were later than the standard condition. Compressive, bending and bond strength were similar with three types as follow. In compressive strength, initial strength of the low were smaller than the standard but the low in the long-term were similar with the standard. On the contrary to this, bending strength were similar in initial strength but the low in the long-term were smaller than the standard. The low in bond strength was average 35% less than the standard. Length changes was as in the following : A > C > B. the low is two times much as the standard but the case using blast furnace slag particles noticeably reduced length changes. Water absorption coefficient and water vapor resistance were as in the following : C > A > B. In case of URHM added bottom ash, water absorption coefficient and water vapor resistance were increased because bottom ash is porous material.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.49-55
• /
• 2017

In this study, gas turbine engine inlet duct was designed to satisfy uniform flow at aerodynamic interface plane (AIP). Haack-series was selected as nose cone profile and duct outer radius($r_o$) was designed to satisfy to match with area change rate between the nose cone and outer duct wall by the 1-D sizing. The design object of the inlet duct wall profile which has the gradual area change rate was uniform Mach number in the core flow region and minimum boundary later thickness at the both inner nose wall and outer duct wall. The flow characteristics inside the inlet duct was evaluated using CFD. The static pressure distribution at the AIP showed uniform pattern within 0.16%. Based on Mach number profile, the boundary layer thickness was 2% of channel height. Kiel temperature rake location was decided less than 100 mm in front of nose cone where the Mach number is less than 0.1 in order to maximize the temperature probe recovery rate.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.12
• /
• pp.42-48
• /
• 2008

Next generation wireless communication systems require RF transceivers that enable multiband/multimode operations. Polar transmitters are known as good candidates for high data rate systems such as EDGE (Enhanced Data Rates for GSM Evolution), WCDMA (Wideband Code Division Multiple Access), and WLAN (Wireless Local Area Network) because they can obtain high efficiency by using efficient switched-mode RF power amplifiers. In this paper, we investigate the performance of a simple peak windowing scheme for the OFDM (Orthogonal frequency Division Multiplexing) polar transmitter, which requires no change of a receiver structure or no additional information transmission. The approach we employed is to apply the peak windowing scheme to the amplitude modulated signals of the polar transmitter to reduce the PAPR (Peak-to-Average Power Ratio). The BER (Bit Error Rate) and EVM (Error Vector Magnitude) performances are measured for various window types and lengths. The simulation results demonstrate that the proposed algorithm mitigates out-of-band distortion introduced by clipping along with PAPR reduction.