DOI QR코드

DOI QR Code

Analysis of the Characteristics of Manufactured Concrete, according to the Type of Admixture used when Remixing and Placing it

혼화제 종류별로 제조된 콘크리트의 재 혼합 타설시 특성 분석

  • Received : 2010.08.30
  • Accepted : 2010.10.11
  • Published : 2010.10.20

Abstract

In recent years, the demand for the development of high quality and cost effective materials, as well as the competition to ensure a diverse and sufficient amount of ready-mixed concrete, has been increasing rapidly. In this experiment, concretes made with different admixtures are blended with each other in different combinations and ratios, in order to identify potential problems. The first test was a slump level test, in which all of the concretes met the required numbers, as they also did in the test for air content. Plain organic acid concrete scored the highest in bleeding amount, but organic acid mix in general showed a similar outcome. In the early measurement of compressive strength, plain naphthalene concrete was the strongest. Of the blends, the 5:5 mix of organic acid and naphthalene was the strongest. In the standard measurement, the 5:5 mix of naphthalene and lignin was the strongest. Tensile strength tests revealed similar results. Length change rate proved to be greater in blended concrete than in plain concrete, and dry shrinkage rate was highest in the 7:3 ratio blends. Through SEM photo analysis, it was confirmed that the 7:3 ratio blends contained more micro-voids. In conclusion, with the exception of a specific few combinations, it was found that the blending of different types of concrete is undesirable due to the delayed coagulation time as well as the early decrease in strength.

최근 들어 경제성장과 산업기반 시설의 확충 등으로 인하여 타사의 레미콘을 종종 혼용 하는 경우가 있는데, 사용되는 혼화재료의 경우 제조회사별로 화학성분 및 첨가량의 차이가 있으므로 서로 다른 레미콘 제조회사의 콘크리트가 혼합되었을 시에 강도 저하 및 응결지연, 내구성 저하 등으로 인한 콘크리트의 성능 저하요인이 발생된다. 혼화제 종류별로 제조된 콘크리트의 재 혼합 타설시의 성능 분석을 한 결과로서 먼저 슬럼프는 모든 콘크리트에서 목표슬럼프 값을 만족하였으며, 공기량 역시 모든 콘크리트에서 목표 공기량을 만족 하였다. 블리딩량 및 블리딩률의 경우 전반적으로 유기산계와 같이 혼합된 콘크리트에서 높은 블리딩량을 나타내었다. 조기재령의 압축강도는 Plain의 나프탈린계에서 가장 큰 강도발현 경향을 나타내었고, 재 혼합 콘크리트에서는 5:5의 유기산계와 나프탈린계에서 가장 큰 압축 강도 발현 경향을 나타내었다. 표준재령의 경우 5:5의 재 혼합 콘크리트 중 나프탈린계+리그닌계를 혼합하였을 때 가장 큰 강도 발현 경향을 나타내었다. 인장강도 역시 압축강도와 유사한 경향을 나타내었다. 길이변화율은 전반적으로 Plain에 비하여 큰 건조수축 경향을 나타내었으며, 재 혼합콘크리트 7:3의 경우에 가장 큰 건조수축경향을 나타내었다. SEM사진 분석결과 재혼합 콘크리트에서 더 많은 미세공극들이 발견되었다. 결과적으로 한 종류의 레미콘을 이용하여 타설하였을 경우 보다 혼합사용 하였을 경우 응결지연 및 초기강도 저하현상이 나타나고, 더 큰 건조 수축 경향을 나타내어 일부 혼화제를 선별하여 혼합 사용하는 경우를 제외하고는 가능한 동일한 혼화제를 사용해야 할 것으로 판단된다.

Keywords

References

  1. Byeon GJ, Admixture, Korea Ready-mixed Concrete Industry Association, 1990.
  2. Han CG, Ready-mixed Concrete Guide, Kimundang Publishing, 2006.
  3. Conference proceedings of Architectural Institute of Korea, 2003;95-102,
  4. Mun HY, Construction Materials Engineering, Dong Myeong Publishing, 1995. p.85-126
  5. Ministry of Construction and Transportation, Concrete Standard Specification, 2000
  6. Korea Concrete Institute, Concrete Admixture, Kimundang Publishing, 1997, p.28-89
  7. Kim JH, Yun JH, Air-entraining Agent and Water-reducing Agent, Journal of Korea Concrete Institute 1996:8(2):1018-1415
  8. ASTM, Symposium on Effect of Water-Reducing Admixtures and 17. Set-Retarding Admixtures on Properties of Concrete, STP-266, 1960

Cited by

  1. Life cycle CO2 assessment of concrete by compressive strength on construction site in Korea vol.16, pp.5, 2012, https://doi.org/10.1016/j.rser.2012.02.014