• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.3
• /
• pp.21-32
• /
• 1992

Numerical solutions are presented for solving the free surface flow created by a three-dimensional body moving beneath the free surface with constant velocity at an angle of attack. The solution is obtained using a panel method based on the perturbation potential, which employs Havelock sources and normal dipoles distributed on the body surface and Havelock normal dipoles in the wake downstream of the trailing edge. A pressure Kutta condition with an iterative solution procedure is implemented to satisfy equal pressure condition on the upper and lower surfaces at the trailing edge. Numerical calculation examples in the present paper include an ellipsoid at zero angle of attack, a rectangular planform wing at a small angle of attack in the limit of zero Froude number and then free surface flows and hydrodynamic forces acting on the submerged spheroid and parabolic strut are calculated. Discussions are made about the validity of the present method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.273-279
• /
• 2009

In this paper, an antenna which has dipole-like radiation pattern and low profile is proposed. The antenna is composed of four elements slot array based on L-shaped 0.43 $\lambda_g$ slot element. It presents a omni-directional radiation patter in the azimuth plane and has a null toward broad-side direction. In the design, a small mono-pole antenna which acts as a large capacitance element, combined with the partially removed ground plane by four L-shaped slots. As a result, these structure act as a LC resonator for radiation. The measured result shows, the impedance bandwidth(VSWR$\leq$2) of the proposed antenna is 60 MHz(2.35$\sim$2.41 GHz). The measured maximum radiation gain and efficiency of proposed antenna is 0.02 dBi, 56.7 % at center frequency 2.38 GHz, respectively. The proposed antenna can be applied to wireless tan access point system.

• Journal of The Geomorphological Association of Korea
• /
• v.18 no.1
• /
• pp.101-112
• /
• 2011

Coastal terrace was developed at 7.2m height near Shinchon village in Geoje Island. It is located on the east side of southern coast in Korean Peninsula, where sea-level changes caused by ebb and flow of the tide, embayment are relatively low. Due to the breccia layer by mass-movement, dark grayish clayey formation, marine origin's rounded gravel are deposited sequentially in a cross-section of coastal terrace, so it provides a good example which understand Holocene sea level changes to determine the effect on the various sedimentary environments. For the purpose of identifying the morphogenetic process, Grain size, Roundness, XRD, AMS dating analysis was attempted. As a result, after last glacial age, Holocene sea level rise to +5.6m(4,740±100yrs BP). At that time, various geomorphological features are considered to be formed.

• Journal of the Korean earth science society
• /
• v.36 no.7
• /
• pp.617-631
• /
• 2015

The Sesong Formation, mixed carbonate-siliciclastic deposits of late Middle Cambrian (Series 3) to Furongian in age, in the Taebaeksan Basin shows the Steptoean Positive Carbon Isotope Excursion (SPICE) with the ${\delta}^{13}C$ values ranging from 1.14 to 2.81‰ in the approximately 15-m-thick stratigraphic interval. The SPICE in the Sesong Formation occurs in the lower part of the Paibian Stage which contains trilobite biozones of the Fenghuangella laevis Zone, Prochuangia mansuyi Zone and the lower part of the Chuangia Zone. The Sesong Formation is composed of six lithofacies including laminated mudstone, nodular shale, laminated sandstone, massive sandstone, limestone conglomerate, and limestone-shale couplet facies. The Sesong Formation is known to have been deposited in the outer shelf below storm wave base. The SPICE occurs in the stratigraphic interval associated with highstand systems tract, correlative conformity and transgressive systems tract of the Sesong Formation. The peak carbon isotope value in the SPICE may coincide with the correlative conformity formed by relative sea-level fall. The occurrence of the SPICE in the Sesong Formation suggests that the SPICE can be used as a tool of global correlation for the successions of mixed carbonate-siliciclastics which lack fossils.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.1
• /
• pp.55-63
• /
• 2015

We investigated the zircon U-Pb ages of the metapelites from the Sungjeon-myeon Gangjin-gun, the southwestern Ogcheon belt, to provide geochronological constraints for the depositional age as well as the distribution of Late Paleozoic formation. Data from the detrital zircons are mostly concordant, yielding four major age groups: (1) Neoarchean (~2.5 Ga); (2) Paleoproterozoic (~1.86 Ga, Statherian); (3) Middle Devonian(~390 Ma); and (4) Late Paleozoic (~322 Ma, Serpukhobian). The youngest zircon age gives a weighted mean $^{206}Pb/^{238}U$ age of $322{\pm}4.8$ Ma (n=16, MSWD=4.9), indicating deposition age of Early Carboniferous(Serpukhobian) or after. Therefore, the metapelites is considered to be the lowest Formation of the late Paleozoic Pyeongan Supergroup correlated with the Manhang Formation of the Samcheock coal fields and the Oeumri Formation(the Middle to Late Carboniferous) of the Hwasun coal field.

• Tunnel and Underground Space
• /
• v.29 no.5
• /
• pp.332-345
• /
• 2019

Maximum dip vector of individual joint plane, which can be uniquely defined on the hemispherical projection plane, has been established by considering its dip and dip direction. A new stereographic projection method for the rock slope analysis which employs the maximum dip vector can intuitively predict the failure modes of rock slope. Since the maximum dip vector is uniquely projected on the maximum dip point of the great circle, the sliding direction of discontinuity plane can be recognized directly. By utilizing the maximum dip vector of discontinuity both the plane sliding and toppling directions of corresponding blocks can be discerned intuitively. Especially, by allocating the area of high dip maximum dip vector which can form the flanks of sliding block the potentiality for the formation of virtual sliding block has been estimated. Also, the potentiality of forming the triangular-sectioned sliding block has been determined by considering the dip angle of joint plane the dip direction of which is nearly opposite to that of the slope face. Safety factors of the different-shaped blocks of triangular section has been estimated and compared to the safety factor of the most hazardous block of rectangular section. For the wedge analysis the direction of crossline of two intersecting joint planes, which has same attribute of the maximum dip vector, is used so that wedge failures zone can be superimposed on the stereographic projection surface in which plane and toppling failure areas are already lineated. In addition the maximum dip vector zone of wedge top face has been delineated to extract the wedge top face-forming joint planes the orientation of which provides the vital information for the analysis of mechanical behavior of wedge block.

• Journal of Advanced Navigation Technology
• /
• v.7 no.2
• /
• pp.180-190
• /
• 2003

By using accurate closed-form Green's functions obtained from real-axis integration method, the full-wave analysis of CPW discontinuities are performed in space domain. In solving MPIE(Mixed Potential Integral Equation), Galerkin's scheme is employed with the linear basis functions on the triangular elements in air-dielectric boundary. In the singular integral arising when the observation point and source point coincides, the surface integral is transformed into the line integral and the integral is evaluated by regular integration. By using the Green's function from the real-axis integration method, the discontinuities are characterized accurately.

• The Korean Journal of Applied Statistics
• /
• v.31 no.2
• /
• pp.229-239
• /
• 2018

This paper introduces how to adopt the concept of temporal hierarchies to forecast time series data. Similarly as in hierarchical cross-sectional data, temporal hierarchies can be constructed for any time series data by means of non-overlapping temporal aggregation. Reconciliation forecasts with temporal hierarchies result in more accurate and robust forecasts when compared with the independent base and bottom-up forecasts. As an empirical example, we forecast traffic accident counts with temporal hierarchies and observe that reconciliation forecasts are superior to the base and bottom-up forecasts in terms of forecast accuracy.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.10
• /
• pp.34-40
• /
• 2001

Ultra Wide Band (UWB) system uses wide band signal, which power spectral density is over all band, It likes as a noise floor, so UWB system can be used without interfering with other communication system. For the first time, we adopted Rayleigh mono pulse antipodal signal which had symmetric characteristic and zero mean. With the power spectral density using stochastic process, we knew that the antipodal signaling scheme removed discrete spectrum and concluded that this had much better spectral suppression, probability of error and data rate than PPM (Pulse Positioning Modulation).

• Nuclear Engineering and Technology
• /
• v.27 no.6
• /
• pp.870-876
• /
• 1995

In this paper, a new three-dimensional nodal diffusion code which is based on the AFEN methodology is described and tested. The method expands the homogeneous flux within a node in ter-ms of eighteen analytic basis functions satisfying the diffusion equation at any point of the node. And the nodal coupling equations are derived such that nodal balance, current continuity and leakage balance within an infinitesimally small box around the edge are satisfied. To verify its accuracy, the code was applied to the well-known static LMW benchmark problem and a small core benchmark problem that has the same material properties as the three-dimensional IAEA benchmark problem and compared with two other codes (QUANDRY, VENTURE). The results show that the code provides good accuracy both in the power distribution and in the effective multiplication factor.