• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.571-582
• /
• 2010

Typically nondestructive inspection methods of the large gear units are applied to penetrate non-destructive inspection. Nondestructive penetrating inspection put into the small openings of the defect to penetration liquid, remove to excess penetration liquid on the surface of the gear units, spread with developing solution and we can find the small defect by coating with penetration liquid. However, this method has so many issues because of penetrate nondestructive tests on the gear assembly. The steep angle of screw is hard to achieved full penetration and has the problem to remove the excess. In contrast, the magnetic nondestructive inspection is easy to detect subsurface defects and subtle defects. According to the inspection results the stress concentrates in gear surface, some internal defects and microscopic flaws exist on the gear units are not found to penetrate the nondestructive inspection, but magnetic nondestructive inspection could have found many defect. Therefore, a reasonable method of nondestructive inspection for the large gear units is suitable to magnetic nondestructive inspection.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.12
• /
• pp.953-960
• /
• 2020

This paper presents an optimization of gear web design used in a main gear train of an engine reduction gearbox for a rotorcraft. The optimization involves the minimization of a total weight, transmission error, misalignment, and face load distribution factor. In particular, three design variables such as a gear web thickness, location of rim-web connection, and location of shaft-web connection were set as design parameters. In the optimization process, web, rim and shaft of gears were converted from the 3D CAD geometry model to the finite element model, and then provided as input to the gear simulation program, MASTA. Lastly, NSGA-II optimization method was used to find the best combination of design parameters. As a result of the optimization, the total weight, transmission error, misalignment, face load distribution factor were all reduced, and the maximum stress was also shown to be a safe level, confirming that the overall gear performance was improved.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.270-275
• /
• 2008

The straight bevel gear for automobile part has been manufactured by the cold forging instead of the gear machining tool for the mass production. The application to CAD/CAM system has been necessary in order to develop the precision product quickly by forging through the minimization of trial and error and confirm the reproducibility. In the study, the straight bevel gear with the crown teeth has been modelled by the CAD/CAM system. The master gear after the gearing test has been machined after the modelling, NC data generation and verification. The die for forging and the jig for machining has been manufactured using the master gear.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.104-109
• /
• 2018

Generally, the durability of the parking lock gear is evaluated through an endurance test for the entire transmission but no test standard exists for the durability test of one part of a parking lock gear. Therefore, in this study, the durability test standards of the parking lock gear were determined autonomously, and the durability performance test was conducted. A static fracture test was carried out to determine the yield strength of the parking lock gear, and a durability test condition was set to 60 % of the yield strength. The durability test of 1,000,000 times was conducted under the given conditions using a dedicated test jig manufactured for the test. Because the jig fractured during the static fracture test, finite element analysis for the jig was carried out and the jig was re-designed. The modified jig was manufactured and the durability test was carried out based on the test standard of autonomously. The basic data on the performance and endurance limit of the parking lock gear were obtained using these tests and analyses, and the basic data will be used as fundamental materials for the design and the development of the parking lock gear.

• Journal of the Korean Magnetics Society
• /
• v.24 no.5
• /
• pp.152-159
• /
• 2014

Magnetic gear can transmit torque without any mechanical contact among rotational parts in rotating mechanical systems. Especially, magnetic gear using rare-earth PMs can be used in variety of industry application because of their great power efficiency. Thus, recent trend shows that magnetic gear can be replaced with common mechanical gear. This paper deals with comparison and torque analysis for magnetic gears with parallel and Halbach magnetization according to various design parameters. Using a two dimensional (2D) finite element (FE) analysis, suitable gear ratio is selected. We performed analysis for magnetically connected inner and outer torque with respect to various design parameters including thickness of inner and outer PM, steel pole angle, segments of Halbach array and magnetization pattern of inner and outer PMs. Finally, we can obtain improved design model having parallel and Halbach magnetization with larger torque, compared with an initial design model.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.2
• /
• pp.121-130
• /
• 2023

Finite element analysis is widely used to predict the structural stability and tooth contact performance of gears. This study focused on the effect of finite element modeling conditions of a spur gear on the simulation result and the model simplification. The gear body and teeth, teeth width, configuration of mesh, frictional coefficient, and simulation time interval (gear mesh cycle division) were selected for model simplification for gear analysis. The static transmission error during a single-gear mesh cycle was calculated to represent the performance of the gear, and the elapsed time was measured as a simplification factor. Contact stress distribution was also checked. The differences in maximum transmission error and elapsed time depending on the model simplification methods were analyzed. After all simplification methods were estimated, an optimal combination of the methods was defined, and the result was compared with that of the most detailed modeling methods.

• Journal of Bio-Environment Control
• /
• v.12 no.2
• /
• pp.63-67
• /
• 2003

Cucumber fruits requires a lot of labor to harvest in time in Korea, since the fruits are cut and grabbed by hand. In this study, we developed an end-effector for robotic harvester of cucumber fruits. Its development involved the integration of an end-effector system with a PC compatible, DC motors, and a motor controller board. Software, written in Pic-basic, combined the functions of motor control with various circumstances. Cucumber's properties were measured and analyzed for precision of the end-effector. The results were similar to those of other vegetables. Properties including hardness of cucumber fruits were used as basic data for development of a harvester.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.19-25
• /
• 2016

Using a actuator to which the motor and the gear is applied to the I-PD control method and a dual-loop system to carry out precise position control. I-PD control algorithm performs an operation to reduce the overshoot in the transient response. Accordingly, the actuator obtains a precise position tracking result. Also it utilizes two sensors and dual loops. It reduces the adverse effect on the precise position control that may occur by the end play of the gear train. In this paper, we uses the actuator model applying the BLDC motor and gear in order to determine the position tracking result by the dynamic characteristic change. It was verified by the simulation results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.1027-1032
• /
• 2012

Two types of very small multiplying gears and arrays have been developed for new dental hand-pieces, and the increased speed ratios, modules, number of teeth, gear diameters, and gear types were calculated based on the dynamics of the machinery. The contacting and bending strengths were evaluated for gear teeth with two design concepts using AGMA equations and finite element analyses, and the contacting stresses on teeth with and without DLC (diamond-like-carbon) coating layers were calculated. Fatigue and tension tests were performed to obtain an S-N curve, the Young's modulus, and the strength of the gear material, and these were utilized in the analyses. Slightly larger stresses were found for 2-axis-type gears than for other types of gears, and the S-N curves showed that a gear lifetime of 109 cycles was satisfied. The contacting stresses in gears coated with DLC were reduced by 30%. A new prototype model of a hand-piece with small gears was successfully fabricated and tested.

• Journal of the Korea Convergence Society
• /
• v.2 no.2
• /
• pp.27-34
• /
• 2011

This study is making a product for the development of one process worm wheel of making a shape for gear for worm wheel without hobbing manufacturing process. Because of removing a hobbing process, plastic worm wheel for increased productivity and equivalent quality is produced in the result. As the result, this product is selling to Hyundai Mobis, Mando, TRW, KOYO/NSK/Showa(Japan), Delphai(America). The core technology and different strategy are as follows. The technology protection for molding of worm whee is currently patent process "Molding process of helical gear(No. 10-2008-0105908). Further patent procedure for "molding system for positioning decision of inserting boss is currently prepared. As gear molding procedure in hobbing machine without gear machining procedure, most of all, core development technology which is making a gear tooth is main topic. So that, in case of currently developed worm wheel, because core and mold base are not developed in the first procedure, gear is machining in hobbing M/C as the second procedure. In the later, patent for mold base structure will be prepared in this study results.