• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.347-358
• /
• 2009

Recently, it is getting into a good situation for the flat-plate slab system to be applied. The flat-plate slab without beam, however, is often too weak to control deflection properly compared to other typical slab-beam structures, for which the post-tension method is generally regarded as one of best solutions. The post-tension (PT) method can effectively control deflection without increase of slab thickness. Despite this good advantage, however, the application of PT method has been very limited due to cost increase, technical problems, and lack of experiences. Therefore, in order to reduce difficulties on applying full PT method under the current domestic circumstances and to enhance constructability of PT system, this research proposed the partial PT method with top jacking anchorage applied in a part of span as need. For the top jacking anchorage system, the efficiency of deflection control shall be considered in detail because it can vary widely depending on the location of anchorage that can be placed anywhere as need, and tensile stresses induced at back of the anchorage zone also shall be examined. Therefore, in this study, analysis were performed on the efficiency of deflection control depending on the location of anchorage and on tensile stresses or forces using finite element method and strut and tie model in the proposed top jacking anchorage system. The proposed jacking system were also applied to the floor slabs at a construction site to investigate its applicability and the analysis results of slab behavior were compared to the measured values obtained from the PT slab constructed by the partial PT method. The result of this study indicates that the partial PT method can be very efficiently applied with little cost increase to control deflection and tensile stresses in the region as a need basis where problem exists.

• Journal of Animal Science and Technology
• /
• v.49 no.5
• /
• pp.677-688
• /
• 2007

돼지를 포함한 대부분의 동물은 일정한 발정주기를 가지고 일정한 시기에 배란을 하는 자연배란동물이지만, 토끼, 고양이, 밍크 등의 암놈은 교미자극에 의해 배란이 일어나는 유기배란동물이다. 또한 1년에 한 번만 발정하는 단발정동물과 1년에 수차례 발정하는 다발정동물이 있다. 이 중에서 모돈은 1년에 수차례 발정하는 다발정 동물로서 발정기에 들면 비발정기와는 다른 행동을 나타낸다(Diehl 등, 2001). 양돈가의 수익을 최대화하기 위해서는 비생산일수를 최소로 줄여야 한다. 모돈의 비생산일수를 줄일 수 있는 한 가지 방법은 성공적으로 교배를 시키는 것이다. 이처럼 성공적으로 교배를 시키기 위해서는 수정적기를 정확히 예측해야 한다. 만약 수정적기를 정확히 판단하지 못하여 수태가 되지 않으면, 비생산일수가 늘어나 손실을 입게 된다. 따라서 수정적기를 정확히 판단하는 것은 모돈의 성공적인 인공수정에 있어서 중요한 요소이다. 수정적기는 배란이 일어나기 전 10시간에서 12시간 사이이며, 발정이 시작되는 시점을 기준으로 하였을 때 경산돈의 경우 26시간에서 34시간 사이이고 미경산돈의 경우는 18시간에서 26시간 사이이다(Evans 등, 2001). 현재 하루에 두 번 모돈의 발정을 확인하는 것이 일반화되어 있으며, 이 때 웅돈을 접촉시키거나 육안관찰을 통하여 발정 유무를 판단한다. 이러한 방법에는 숙련된 기술과 풍부한 경험이 요구될 뿐만 아니라 총 소요노동력의 30% 정도가 요구된다(Perez 등, 1986). 하루에 두 번밖에 발정을 감지하지 않기 때문에 발정이 언제 시작되었는지를 정확히 알 수 없으며, 또한 발정의 대부분이 새벽에 시작되므로 수정적기를 정확히 판단하기란 매우 어렵다. 만약 발정을 감지했더라도 적기에 인공수정을 하지 못한다면, 수태율이 낮아지므로 경제적 손실이 초래된다. 현재 이러한 문제점 때문에 2회에서 3회에 걸쳐 인공수정을 하고 있으나 이에 따른 소요비용과 소요노동력 등은 양돈가의 부담을 가중시키는 요인이 되고 있다. 돼지는 발정기가 되면 비발정기에 나타내지 않던 외음부의 냄새를 맡는 행동, 귀를 세우는 행동 및 승가허용 행동 등을 나타낸다(Diehl 등, 2001). 또한 돼지는 비발정기에 비하여 발정기에 더 많은 활동량을 나타낸다(Altman, 1941; Erez and Hartsock, 1990). Freson 등(1998)은 스톨에서 개별적으로 사육되고 있는 모돈의 활동량을 적외선센서를 이용하여 측정함으로써 발정을 86%까지 감지하였다고 보고하였다. 그러나 이 연구는 단지 모돈의 발정을 감지하였을 뿐 번식관리에 있어서 가장 중요한 수정적기의 판단 기준을 제시하지 못하였다. 따라서, 본 연구는 스톨에서 사육되는 모돈의 활동량을 측정함으로써 발정시작시각을 감지하고 이를 기준으로 인공수정적기를 예측할 수 있는 인공수정적기 예측 장치를 개발한 후 이의 성능을 농장실증실험을 통하여 시험하고자 수행되었다.

• Journal of the Korean earth science society
• /
• v.41 no.2
• /
• pp.155-175
• /
• 2020

The purpose of this study is to analyze the 2015 revised Science Curriculum and Environment Curriculum, and to provide implications for the correlation and complementarity between the two standards. For the analysis of the curriculum, the contents system of the two standards was reorganized based on the four categories of knowledge, attitude, inquiry, participation and practice, which are common literacy elements of science and environment, based on previous studies. Content Analysis was performed on content elements and detailed performance expectation. As a result of this study, there was a difference in terms of the core competencies and goals. The Environment Curriculum emphasized sustainable development and social participation while the Science Curriculum emphasized scientific inquiry and literacy. The contents system analysis results according to the four literacy factors are as follows. First, in terms of attitude, both standards deal with research ethics in common. However Environment Curriculum values learners' values and views on the environment more than Science Curriculum which emphasizes the science attitude as science investigators. Second, there was a serious problem in the knowledge linkage between two standards. In same grade groups, the level of content knowledge dealt in two standards was not consistent. Third, in the inquiry aspect, the Environment Curriculum deals with interdisciplinary topics in the purposefully designed inquiry unit, whereas the Science Curriculum presents various research activities based on related science concepts in every unit. Fourth, in the participation and practice aspect, the Environment Curriculum focused on participation and practice while the Science Curriculum focused on sustainable science and technology development and improvement, scientific interest and decision-making ability. This study provide implications for education for sustainable development(ESD) by providing the complementary potentials between Science Curriculum and Environment Curriculum.

• Korean Chemical Engineering Research
• /
• v.56 no.4
• /
• pp.577-584
• /
• 2018

This study was conducted to investigate the potential of chicken feather (CF), which is a by-product in poultry industry, as a partial substitute of wood fiber in the production of wood-based fiberboard. Keratin-type protein constituted the majority of CF, and its appearance did not differ from that of wood fiber. When the formaldehyde (HCHO) adsorptivities of CF compared by its pretreatment type, feather meal (FM), which was pretreated CF with high temperature and pressure and then grounded, showed the highest HCHO adsorptivity. In addition, there was no difference between the adsorbed HCHO amounts, which was measured by dinitrophenylhydrazine method, of scissors-chopped CF and CF beated with an electrical blender. Mechanical properties and HCHO emission of medium-density fiberboards (MDF), which were fabricated with wood fiber and 5 wt% CF, beated CF or FM based on the oven-dried weight of wood fiber, were not influenced by the pretreatment type of CF. However, when the values compared with those of MDF made with just wood fiber, thickness swelling and HCHO emission of the MDF were improved greatly with the addition of CF, beated CF or FM. Based on the results, it might be possible to produce MDF with improved dimensional stability and low HCHO emission if CF, beated CF or FM is added partially as a substitute of wood fiber in the manufacturing process of MDF produced with the conventional urea-formaldehyde resin of $E_1$ grade. However, the use of CF or FM in the production of MDF has a low economic feasibility at the current situation due to the securing difficulty and high cost of CF. In order to enhance the economic feasibility, it requires to use CF produced at small to medium-sized chicken meat plants. More importantly, it is considered that the technology developed from this research has a great potential to make provision for the prohibition of animal-based feed and to dispose environmentally avian influenza-infected poultry.

• Journal of Korea Spatial Information System Society
• /
• v.6 no.1 s.11
• /
• pp.73-85
• /
• 2004

Recently, as the growth of the wireless Internet, PDA and HPC, the focus of research and development related with GIS(Geographic Information System) has been changed to the Real-Time Mobile GIS to service LBS. To offer LBS efficiently, there must be the Real-Time GIS platform that can deal with dynamic status of moving objects and a location index which can deal with the characteristics of location data. Location data can use the same data type(e.g., point) of GIS, but the management of location data is very different. Therefore, in this paper, we studied the Real-Time Mobile GIS using the HBR-tree to manage mass of location data efficiently. The Real-Time Mobile GIS which is developed in this paper consists of the HBR-tree and the Real-Time GIS Platform HBR-tree. we proposed in this paper, is a combined index type of the R-tree and the spatial hash Although location data are updated frequently, update operations are done within the same hash table in the HBR-tree, so it costs less than other tree-based indexes Since the HBR-tree uses the same search mechanism of the R-tree, it is possible to search location data quickly. The Real-Time GIS platform consists of a Real-Time GIS engine that is extended from a main memory database system. a middleware which can transfer spatial, aspatial data to clients and receive location data from clients, and a mobile client which operates on the mobile devices. Especially, this paper described the performance evaluation conducted with practical tests if the HBR-tree and the Real-Time GIS engine respectively.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.17 no.2
• /
• pp.108-125
• /
• 2015

The agro-climatic index is one of the ways to assess the climate resources of particular agricultural areas on the prospect of agricultural production; it can be a key indicator of agricultural productivity by providing the basic information required for the implementation of different and various farming techniques and practicalities to estimate the growth and yield of crops from the climate resources such as air temperature, solar radiation, and precipitation. However, the agro-climate index can always be changed since the index is not the absolute. Recently, many studies which consider uncertainty of future climate change have been actively conducted using multi-model ensemble (MME) approach by developing and improving dynamic and statistical downscaling of Global Climate Model (GCM) output. In this study, the agro-climatic index of Korean Peninsula, such as growing degree day based on $5^{\circ}C$, plant period based on $5^{\circ}C$, crop period based on $10^{\circ}C$, and frost free day were calculated for assessment of the spatio-temporal variations and uncertainties of the indices according to climate change; the downscaled historical (1976-2005) and near future (2011-2040) RCP climate sceneries of AR5 were applied to the calculation of the index. The result showed four agro-climatic indices calculated by nine individual GCMs as well as MME agreed with agro-climatic indices which were calculated by the observed data. It was confirmed that MME, as well as each individual GCM emulated well on past climate in the four major Rivers of South Korea (Han, Nakdong, Geum, and Seumjin and Yeoungsan). However, spatial downscaling still needs further improvement since the agro-climatic indices of some individual GCMs showed different variations with the observed indices at the change of spatial distribution of the four Rivers. The four agro-climatic indices of the Korean Peninsula were expected to increase in nine individual GCMs and MME in future climate scenarios. The differences and uncertainties of the agro-climatic indices have not been reduced on the unlimited coupling of multi-model ensembles. Further research is still required although the differences started to improve when combining of three or four individual GCMs in the study. The agro-climatic indices which were derived and evaluated in the study will be the baseline for the assessment of agro-climatic abnormal indices and agro-productivity indices of the next research work.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.6 no.2
• /
• pp.71-84
• /
• 2004

There is a growing demand for agrometeorological information that end-users can use and not just interesting information. lo achieve this, each region/community needs to develop and provide localized climate and weather information for growers. Additionally, provide tools to help local users interpret climate forecasts issued by the National Weather Service in the country. Real time information should be provided for farmers, including some basic data. An ideal agrometeorological information system includes several components: an efficient data measuring and collection system; a modern telecommunication system; a standard data management processing and analysis system; and an advanced technological information dissemination system. While it is conventional wisdom that, Internet is and will play a major role in the delivery and dissemination of agrometeorological information, there are large gaps between the "information rich" and the "information poor" countries. Rural communities represent the "last mile of connectivity". For some time to come, TV broadcast, radio, phone, newspaper and fax will be used in many countries for communication. The differences in achieving this among countries arise from the human and financial resources available to implement this information and the methods of information dissemination. These differences must be considered in designing any information dissemination system. Experience shows that easy across to information more tailored to user needs would substantially increase use of climate information. Opportunities remain unexplored for applications of geographical information systems and remote sensing in agro meteorology.e sensing in agro meteorology.

• Management & Information Systems Review
• /
• v.30 no.4
• /
• pp.293-314
• /
• 2011

The current study investigated the position of future strategy analyzed from the perspective of design management in relation to 10 strategic industries implemented through 3 steps based on promising growth and advancement of Busan industries and evidence provided from a study on the development program of design industry in Busan. It elucidated the role of design industry as a key role from the perspective of design management in an age of creative revolution of futures values. It analyzed the associations between composition of future strategy and design industry in 10 strategic industries of Busan, and explained the relationships with the strategic industries. The perspective of design management involves that design as a ground of values is an industry of the future values, which performs a key strategic function and role, and a theoretical investigation examined the relationships between main functions of design management and business management. Chapter 3 organized items proposed in the design development program in Busan and examined goals and systems which become basic formation of establishment of design strategy in Busan and conditions for design industry in the associations with strategic industry. Chapter 4 described priorities of practicability by step through analyzing and grouping top 30 projects in Busan industry including meanings as key strategy, position relations, and policy priorities by analyzing elements of design management of strategic industry and describing and analyzing the concept of promoting Busan design. The theme of the present study is to change perception of design management as a key value and a condition to decide creativity industry into future industry and to evaluate vision of Busan design industry and meanings proposed as proceeding strategy. The early 21st century is an age when agrarian society has changed into industrial society is dominated by knowledge economy of the information revolution and one should prepare for the growth phase of creative innovation based on creative revolution of the 4th wave of creative society by design management which has become a center in 2000s on the whole. With the advent of creative paradigm and based on the function and role of the current creative economy age new innovation DNA of design management will be created. Design process has changed through information and knowledge-oriented trends of digital through convergence between industries from industrial design to convergence of industries, and it is expected that integrated design of value creation using information and technology will play a key role in Busan design industry development and top 10 strategic industries.

• Maritime Security
• /
• v.4 no.1
• /
• pp.57-82
• /
• 2022

The objective of this treatise is to explore the limitations of the current navy manpower utilization system and the ways to improve it from the perspective of Generation Z. As Generation Z, following Millennials, has finally come of age, this new group is constituting a gradually greater proportion of military personnel. Due to the typical characteristics of naval operations, the harmony between Millennials and Generation Z, which is differentiated from Generation X in view of dispositions and traits, is one of the essential issues to be discussed. Generally, in a naval vessel, there are numerous pieces of equipment necessary to carry out a wide range of missions and a large number of crew members who operate them with consistent levels of fighting power. This is all while members are living together within the narrow space throughout the 24 hours of each day. Under such particular circumstances, any inter-generational conflicts may have a disruptive effect on the successful accomplishment of naval missions. Currently, new generations of military personnel are facing social difficulties in different aspects compared with the previous generations, and also have different viewpoints on the military. In this regard, in order to foster true harmony between generations, it is considered necessary to take a closer look at the inter-generational differences from their respective standpoints and to examine whether the military organization has taken adequate steps to respond to such changes. Accordingly, Chapters 1 and 2 cover the environments in which Millennials and Generation Z were raised during their childhood to young adulthood, which are distinct from those of older generations, their viewpoints formed based on such backgrounds, and the need to resolve various conflicts between generations. In Chapter 3, the current actions taken by overseas military powers to enhance the coexistence with Generation MZ are analyzed to find the significant implications they had. Chapter 4 examines the operation environments specific to the navy; identifies the potential barriers to achieving harmony between generations by assessing the current status of personnel utilization in the Korean navy in terms of the seaman, petty officer, and the officer, as well as policy; and outlines the solutions to drive harmony. Finally, Chapter 5 emphasizes the need to establish a genuine empathy between generations based on the understanding of unique inter-generational characteristics. This section also discusses the importance of addressing difficulties in utilizing technology-centered naval manpower, and forecasts a scenario of a naval organization that resolves the problem of utilizing naval personnel and the inter-generational conflicts in the future.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.4 no.1
• /
• pp.110-118
• /
• 2002

This study was conducted to investigate the physiology of optimal reproductive age in Hanwoo for protection to decrease of reproductivity and improvement of production of offspring. Thirty two cows were devided into 4 groups of treatments : T1(12 months of age and 0.5kg daily gain), T2(12 months of age and 0.8kg daily gain), T3(15 months of age and 0.5kg daily gain) and T4(18 months of age and 0.5kg daily gain). The days of the first heat of treated cows were 263.3±6.4 days and average weight was 181.1±11.3kg. The conception rates of first insemination were 25%(T1) and 75%(T4), and the number of insemination of T3 and T4(both 1.5) was lower than those of T1 and T2(2.3 and 2.4), respectively. With regard to estrus return after the first parturition, T1, T2, T3 and T4 showed 66.2,76.7, 62.4 and 68.5 days, respectively, indicating the average days of estrus return was 65.7. Plasma progesterone(P4) concentration was nearly the same during the observation periods of treated cows and P4 began to be detected after 12months. Only 5(15.6%) out of 32cows showed normal estrus cycle and ovulation before 12 months. During the peri-parturition period, P4 concentration was rapidly decreased and there was no detection of P4 from parturition to 40 days after milking. P4 would be released again on 45 day after parturition. The results imply that the optimal reproductive age of Hanwoo heifers would be around at the 14 months of age, 110cm height and 265kg weight.