• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.8
• /
• pp.79-88
• /
• 2009

This paper presents the analytical stiffness analysis method for a low-DOF planar parallel manipulator. An n-DOF (n<3) planar parallel manipulator to which 1- or 2-DOF serial mechanism is connected in series may be used as a positioning device in planar tasks requring high payload and high speed. Differently from a 3-DOF planar parallel manipulator, an n-DOF planar parallel counterpart may be subject to constraint forces as well as actuation forces. Using the theory of reciprocal screws, the planar stiffness is modeled such that the moving platform is supported by three springs related to the reciprocal screws of actuations (n) and constraints (3-n). Then, the spring constants can be precisely determined by modeling the compliances of joints and links in serial chains. Finally, the stiffness of two kinds of 2-DOF planar parallel manipulators with simple and complex springs is analyzed. In order to show the effectiveness of the suggested method, the results of analytical stiffness analysis are compared to those of numerical stiffness analysis by using ADAMS.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.455-460
• /
• 2003

180km/h 급 한국형 틸팅차량의 틸팅 메카니즘 기구동역학 해석을 통하여 얻어진 틸팅 대차를 형성하는 주요 파라메터들의 값을 기반으로 틸팅대차용 엑츄에이터의 성능과 용량을 계산하여 설계에 결과를 반영하고자 한다. 승객의 안락감을 유지하기 위해 차체 틸팅 각가속도에 Sine 연속 함수를 적용하여 차체의 틸팅 제어 패턴을 결정하였으며, 이를 통해 차체의 틸팅 각속도와 틸팅각의 패턴을 얻어내었다. 또한 이번 연구를 통해 틸팅 메카니즘의 파라메타를 변화하면서 각각의 틸팅각에 따른 Swing bar 와 엑츄에이터에 작용되는 반발력에 대한 영향력을 분석, 검토하였으며, 이에 따른 엑츄에이터의 출력과 변위 속도등의 변화를 조사하였다. 이러한 결과와 틸팅 메카니즘 기구동력학 해석의 결과를 토대로 틸팅차량이 요구하는 최적의 틸팅 운동을 수행하는 파라메타를 결정하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.1007-1008
• /
• 2009

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.7 s.262
• /
• pp.777-783
• /
• 2007

Since the performance of the circuit breaker mainly depends on the spring operating mechanism, the analysis of the spring operating mechanism is required. The spring, especially closing spring, stores the deformation energy due to the compression and then accelerates the big loads rapidly in the circuit breaker. To accurately carry out the kinematic and dynamic analysis of the circuit breaker, the precise modeling of the spring behavior is necessary. In this paper, the static stiffness of the spring is captured by using the tester. A simple mechanism similar to the spring operating mechanism was designed to generate the release motion of the spring. A high speed camera was used to capture the behavior of the spring. Three types of spring models such as a linear spring model, modal spring model, and nodal spring model are suggested and compared with the experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.409-414
• /
• 2007

Nowadays, with the advancement of computational mechanics, and vehicle dynamics simulation linked up with virtual testing laboratory(VTL) and virtual proving ground(VPG) technologies has become a useful method for analyzing numerous driving performances and diverse noise/vibration characteristics. In this paper, the analytical vehicle model based on multi-body dynamics theory was developed to investigate the vibration characteristics according to various road conditions. For the purpose, the whole vehicle parameters, each vehicle's part parameter, and part connecting elements such as spring, damper, and bush were measured by an experiment. Also, the vehicle dynamics model, which includes the front suspension, rear suspension, steering, front wheel, rear wheel, and body subsystems has been constructed for computer simulation. With the developed vehicle dynamics model, three forces and three moments measured at each wheel center were applied to evaluate and analyze dynamics and vibration characteristics for miscellaneous road conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.187-193
• /
• 2002

Since the bus is regarded as the one of the most public transportation systems, research on the safety and facilities of the bus has been increased actively in recent years. In this paper, we concern the design of the bus door mechanism that is composed of many linkages and actuators(or motors). In particular, the folding door mechanism is representative system installed in most of urban buses. To design the folding door mechanism, we construct the kinematic and dynamic analysis model fur computer simulation. Also, the dynamic analysis is accomplished by both direct dynamics and inverse dynamics. Since the folding door mechanism has many design variables, the analysis program is developed to perceive kinematic and dynamic characteristics according to the design variables and simulation conditions.

• Transactions of the KSME C: Technology and Education
• /
• v.3 no.2
• /
• pp.141-148
• /
• 2015

In this study, the VCB(Vacuum Circuit Breaker) has been developed using the Recurdyn that is widely used on multibody dynamics analysis. The VCB consists of three main circuits with the VI(Vacuum Interrupter) and the main frame with the operating mechanism. This analytic model is validated by comparing the simulation results and the experimental results. Generally, in order to reliably cut off the breaking current, the opening speed of the VCB after contact separation has to be a 0.9~1.1m/s. Therefore, the study of the design parameters of the VCB is needed. To improve the opening velocity, Taguchi design method is applied to optimize the design parameters of a VCB with a lot of linkages. In addition, to evaluate the improvement of the operating characteristics, the simulation results are compared with the Recurdyn and experimental results with improved prototype sample.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.648-657
• /
• 2014

This paper is about the study on a newly developed small waterproofed 4-axis robot arm and the analysis of its kinematics and dynamics. The structure of robot arm is designed to have Pitch-Pitch-Pitch-Yaw joint motion for inspection using a camera on itself and the joint actuator driving capacity are selected and the joint actuators are designed and test for 10m waterproofness. The closed-form solution for the robot arm is derived through the forward and inverse kinematics analysis. Also, the dynamics model equation including the damping force due to the mechanical seal for waterproofness is derived using Newton-Euler method. Using derived dynamics equation, a sliding mode controller is designed to track the desired path of the developed robot arm, and its performance is verified through a simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.561-566
• /
• 2015

In this paper, the operating stiffness of a parallel robot used to handle heavy packages is optimized. Because the studied model, called a "pick and place robot," is applied for packaging logistics, it is important for the robot to be lightweight so that it may respond rapidly and have high stiffness to allow sufficient operating precision. However, these two requirements of low weight and high stiffness are mutually exclusive. Thus, the dynamic characteristics of the robot are analyzed through multibody dynamics analysis, and topology optimization is conducted to achieve this exclusive performance. Lastly, the reliability of the topology optimization is verified by applying the optimized design to the parallel robot.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.10
• /
• pp.958-966
• /
• 2007

This study presents full vehicle dynamics model for the dynamic characteristic analysis of chassis parts which are suspension and brake system. This vehicle dynamics model is appled to kinematics and quasi-static analysis for each chassis part. In order to develop the vehicle dynamics model, the parameters of each chassis element part which are bush, spring and damper are measured by experiment. Also the wheel forces and moments of 6 DOF are measured at each wheel center. These data are applied to input parameter for vehicle dynamics model. And the verification of the developed model is achieved to comparison with the experimental force data of spring, trailing arm and assist arm by using the load response by strain gauge. These experimental force data are acquired by road test at event surfaces of P/G which are belgian and chuck holes roads.