• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.4
• /
• pp.162-167
• /
• 2005

As the properties of porous materials during the drying process relate to the atomistic defects of heterogeneous materials such as dislocation, grain, grain boundary, pore, etc., the knowledge of nano-scale analysis is needed in order to accurately analyze the drying process for porous materials. In this study, the atomic behavior of porous materials Is statically predicted by using the molecular dynamics simulation and the nano-scale material properties are computed. The elastic modulus, thermal expansion coefficient, and volumetric heat capacity numerically found from the molecular dynamics simulation are compared with those of experiment and theory and proved the accuracy.

• Journal of the Microelectronics and Packaging Society
• /
• v.3 no.2
• /
• pp.27-38
• /
• 1996

Lithium fluorhectorite 결정상을 함유한 glass ceramics 분말의 형성과 제조된 glass ceramics 분말을 이용한 저온 소결기판의 특성평가를 하였다. Li2O-MgO-MgF2-SiO2 계 유 리로 핵형성 및 결정 성장을 실시하여 lithium fluorhectorite 결정상을 지닌 glass ceramics 를 제조하였다. 유리시편의 핵형성 온도는 46$0^{\circ}C$였고 결정성장온도는 600, 640, 110$0^{\circ}C$에서 나타났다. $600^{\circ}C$에서의 결정상으 Li2.4LiSi4O10F2가 나타났다. Li2.4Mg8LiSi4와 Li2.8Mg0.6SiO4은 lithium fluorhectorite 결정상으로 되기 위한 중간상임을 확인할수 있었다. 64$0^{\circ}C$에서 열처리 후 110$0^{\circ}C$에서 재열처리하여 형성된 결정은 lithium fluorhectorite 와 tridymite가 최종 결정 상으로 나타났다. 이것은 수중에서 water swelling 현상에 의하여 분말화할 수 있었다, 기판 제조용 slurry를 제조하기 위해 glass ceramics 분말에 Al2O3분말을 0,25,50wt%로 혼합한것 과 glass ceramics 분말에 potashborosilica-te glass 분말을 15, 30, 45, 60 wt% 로 배합하 여 doctor blade 법으로 green sheet를 제조하였다. green sheet 는 950~150$0^{\circ}C$로소성하여 기판의 특성을 평가하였다. 겉보기 기공율은 3.06~19,14%이었고, 전기적 특성으로 유전상수 는 3~5(100KHz)를 나타내었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.1
• /
• pp.27-31
• /
• 2015

The degradation of refractories can be caused by erosion, friction of abrasive particles, as well as by corrosion by molten slag in the gasification reactors. There was little knowledge about the erosion of refractories so far. The castable refractories of which the maximum applying temperature of 1300 and $1500^{\circ}C$ were abraded using SiC particles varying the incidence angles. It was revealed that the maximum abrasion was occurred at the incidence angle of $60{\sim}75^{\circ}$ not at $90^{\circ}$ and thought that the porosity of the refractories was the principle factor.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.86-90
• /
• 2000

The mixed body of clay and flyash containing unburnt carbon was examined at various sintering conditions in order to recycle flyash as environment-affinitive construction materials. Experimental results can be summarized as follows : when large aggregate of 2.54 cm dia. was sintered at a heating rate of $20^{\circ}C$/min, heterogeneous phase with bulgings, inner pores, and cracks were observed at the sintering temperature of $1200^{\circ}C$. Accordingly, heating patterns for the complete removal of the heterogeneous phase were proposed as countermeasures. The compressive strength of finally obtained aggregate was 670~870kg/$\textrm{cm}^2$, which is over two and a half times stronger than the minimum requirement of 200kg/$\textrm{cm}^2$.

• Membrane Journal
• /
• v.29 no.4
• /
• pp.202-215
• /
• 2019

Molecular sieve membranes separate molecules based on their size and/or shape and have been of high interest, due to their potentially high energy efficiency and high selectivity. Zeolite MFI membrane is one of the most-studied molecular sieve membranes and has affected following studies on other molecular sieve membranes. This review discusses the technical developments on the control of morphology, microstructure, and defect of MFI membranes, which have significantly improved xylene isomer separation performances. These include crystal morphology control, effective secondary growth, seed coating method, crystal orientation control, heteroatom doping, and defect healing method.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.4
• /
• pp.167-172
• /
• 2019

The strength (MPa), hardness (Hv), shrinkage (%) and biological properties of the HAp were measured by using an organic plasticizer which facilitates the molding and heat treatment. Mechanical properties such as compressive strength, bending strength and hardness were increased with increasing amount of plasticizer, but mechanical properties were decreased when plasticizer was added more than 7 %. This is because addition of the plasticizer above the allowable value causes cracking during molding, and such cracks promote the generation of microcracks and pores at the time of sintering, resulting in a decrease in mechanical properties. As a result of the antimicrobial activity test, no bacteria were detected regardless of the addition amount of plasticizer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.247-253
• /
• 1996

Microscopic analysis has been performed in order to investigate effects of the microstructure of the starting feed rods on the morphology of the S-L interface and the stability of the molten zone during single crystal growth of $SrTiO_{3}$ using a floating zone method. Undoped and $Fe_{2}O_{3}$ doped $SrTiO_{3}$ doped $SrTiO_{3}$ specimens, sintered at the different temperatures have been used. In the case of the feed rods sintered at the lower temperature($1400^{\circ}C$), the poor densification made the stability of the molten zone difficult to maintain. The feed rods sintered at the higher temperature ($1600^{\circ}C$) exhibited the higher density but their molten zone was difficult to maintain due to the presence of the abnormally grown grains. It is concluded that the uniform grain size distribution of the feed rod is the critical factor to maintain the stable molten zone and therefore to give optimum growth condition during FZ single crystal growth.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.7
• /
• pp.1021-1029
• /
• 1997

In metalforming, ductile fracture criteria have been used for the purpose of predicting fracture occurrence in the stage of process design prior to manufacturing. In the present investigation, some of popular criteria are reviewed to find the most suitable one among them. As a result, it is found that the modified Cockroft and Latham criterion is better than others. The reasons are: it agrees with Roy's and McClintock's void growth models, it is more general than Oyane's and Kuhn's criteria, and it predicts fractures in compression as well as in tension well. However, it is also found that the criterion is incapable of predicting fractures in torsion.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.48-48
• /
• 2003

미세기공(microporous)을 가진 제올라이트는 다양한 유기질 분리의 촉매제 및 광학, 화학 센서, 기체 분리 등의 고기능 소재로서 크게 주목받고 있으며, 비표면적의 증가, 새로운 기능의 발현 둥으로 최근 들어 나노크기를 갖는 제올라이트 합성에 관한 연구가 활발히 진행되고 있다. 본 연구에서는 기체 분리에 응용하기 위한 제올라이트 분리막 개발에 앞서 분리막 제조에 유리할 것으로 판단되어지는 적합한 크기와 형상을 갖춘 나노크기의 제올라이트를 합성하였으며 그 특성을 분석하였다. 출발물질로서 실리카 원으로는 TEOS, LUDOX AS-40, Cab-O-SIL 등을 사용하였으며, 템프레이트(TPAOH)와 함께 특정조성의 TPAOH/SiO$_2$,/$H_2O$ 겔을 만들었다. 합성시간을 단축할 수 있는 방법의 연구로서 저온하의 2단계 온도 변화법을 적용하였으며, 결정성장속도의 향상을 목적으로 NaH$_2$PO$_4$, H$_2$SO$_4$, NH$_4$OH 등의 결정화 촉진제로 사용하여 수열합성법으로 Silicalite-1를 합성하였다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.311-312
• /
• 2009

By applying the vibrating mill modified slag cement on the concrete pile, the higher compressive strength was measured in spite of its smaller powder volume as comparing its compressive strength with existing products' one. As the result of SEM image observation, it was found that the strength was improved by the decreased size and abundance of pore along with increased cement hydrate in the dense structure.