• Journal of Powder Materials
• /
• v.28 no.6
• /
• pp.462-469
• /
• 2021

Tin/graphite composites are prepared as anode materials for Li-ion batteries using a dry ball-milling process. The main experimental variables in this work are the ball milling time (0-8 h) and composition ratio (tin:graphite=5:95, 15:85, and 30:70 w/w) of graphite and tin powder. For comparison, a tin/graphite composite is prepared using wet ball milling. The morphology and structure of the different tin/graphite composites are investigated using X-ray diffraction, Raman spectroscopy, energy-dispersive X-ray spectroscopy, and scanning and transmission electron microscopy. The electrochemical properties of the samples are also examined. The optimal dry ball milling time for the uniform mixing of graphite and tin is 6 h in a graphite-30wt.%Sn sample. The electrode prepared from the composite that is dry-ball-milled for 6 h exhibits the best cycle performance (discharge capacity after 50^th cycle: 308 mAh/g and capacity retention: 46%). The discharge capacity after the 50^th cycle is approximately 112 mAh/g, higher than that when the electrode is composed of only graphite (196 mAh/g after 50^th cycle). This result indicates that it is possible to manufacture a tin/graphite composite anode material that can effectively buffer the volume change that occurs during cycling, even using a simple dry ball-milling process.

• Journal of the Speleological Society of Korea
• /
• no.63
• /
• pp.1-8
• /
• 2004

The non-magnetic materials with non-conductive showing high structure dispersity were developed on the base of natural quartz and lava-scoria which was collected from Je-ju island in Korea, and treated by methane-chemical technology those were obtained novel properties of magnetization through the analyzing. Depending on the processing conditions and subsequent applications the materials produced by strong methane-chemical reaction (MCR) in alcohol solution showed concurrently magnetic, dielectric and electrical properties. The obtained magnetic-electrical powders classified by aggregate complex of their features as segnetomagnetics, containing a dielectric material as a carrying nucleus, particularly the quartz on that surface one or more layers of different compounds were synthesized having thickness up to 10～50 nm and showing magnetic, electrical and other properties. It was confirmed in magnetizing process that powders of quartz and lava-scoria produced by MCR were better oil adsorbent as of oleophilic and floating matter on water surface although their specific gravities are comparably more than 1 in quartz or less than unity, as that of water, in lava-scoira. Therefore, it will be Possible and very useful to remove low density and light gravity oil spillage in difficult recovery from sea and inland water contamination spread on water surface, by marine accident and ship sinking accident occurring frequently in recent years, by way of magnetic adsorbent conveyer system in continuous, if it could be built up the mass Production system of water-floating magnetizable oleophilic adsorbent materials with use of iow cost and good Qualify lava-scoria spread on volcano district in Je-ju island. And, there will also be urgent advent of necessity with strong possibility to develop useful applications of various magnetic functional materials include oleophilic adsorbent for removal of sea oil-contaminants and maritime pollutants, and other kinds of various utilities in industrial applications and practical uses of novel functional materials in the fields of environments and health care applications with in deep expectation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.5
• /
• pp.21-30
• /
• 2008

The fuel cell generation convert fuel source, and gas directly to electricity in an electro-chemical process. Unlike traditional and conventional turbine engines, the process of fuel cell generation do not burn the fuel and run pistons or shafts, and it has not revolutionary machine, so have fewer efficiency losses, low emissions and no noisy moving parts. A high power density allows fuel cells to be relatively compact source of electric power, beneficial in application with space constraints. In this system, the fuel cell itself is nearly small-sized by other components of the system such as the fuel reformer and power inverter. So, the fuel cell energy's stationary fuel cells produce reliable electrical power for commercial and industrial companies as well as utilities. In this paper, a fuel cell system has been modeled using PSCAD/EMTDC to analyze its electric signals and characteristics. Also the power quality of the fuel cell system has been evaluated and the problems which can be occurred during its operation have been studied by modeling it more detailed. Particularly, we have placed great importance on its power quality and signal characteristics when it is connected with a power grid.

• Journal of the Korean Ceramic Society
• /
• v.42 no.5 s.276
• /
• pp.352-358
• /
• 2005

By calcining at $750^{\circ}C$ for 30 h in $O_2$ stream after milling, $LiNi_{1-y}M_yO_2(M=Zn^{2+},\;Al^{3+}$, and $Ti^{4+}$, y = 0.005, 0.01, 0.025, 0.05, and 0.1) were synthesized and their electrochemical properties were investigated. All the samples had R3m structure. $LiNi_{1-y}Zn_yO_2$ (y = 0.025, 0.05, and 0.1) contained ZnO anuor $Li_2ZnO_2$ as impurities. Among the samples substituted with the same element, the samples with relatively large value of $I_{003}/I_{104}$ and the smallest R-factor had the largest first discharge capacity and good cycling performance. $LiNi_{0.975}A1_{0.025}O_2$ had the largest first discharge capacity (172.5 mAh/g) and good cycling performance (about $89.4\%$ of the first discharge capacity at the 20th cycle). This sample had the largest value of $I_{003}/I_{104}$ and the smallest R-factor among all the samples. In addition, the particles of this sample were finer and their size was more homogeneous than the other samples. $LiNi_{0.95}A1_{0.05}O_2$ had relatively large first discharge capacity 150.4 mAh/g and good cycling performance.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.466-472
• /
• 2007

A technology platform for wafer-level three-dimensional integration circuits (3D-ICs) is presented, and that uses wafer bonding with low-k polymeric adhesives and Cu damascene inter-wafer interconnects. In this work, one of such technical platforms is explained and characterized using a test vehicle of inter-wafer 3D via-chain structures. Electrical and mechanical characterizations of the structure are performed using continuously connected 3D via-chains. Evaluation results of the wafer bonding, which is a necessary process for stacking the wafers and uses low-k dielectrics as polymeric adhesive, are also presented through the wafer bonding between a glass wafer and a silicon wafer. After wafer bonding, three evaluations are conducted; (1) the fraction of bonded area is measured through the optical inspection, (2) the qualitative bond strength test to inspect the separation of the bonded wafers is taken by a razor blade, and (3) the quantitative bond strength is measured by a four point bending. To date, benzocyclobutene (BCB), $Flare^{TM}$, methylsilsesquioxane (MSSQ) and parylene-N were considered as bonding adhesives. Of the candidates, BCB and $Flare^{TM}$ were determined as adhesives after screening tests. By comparing BCB and $Flare^{TM}$, it was deduced that BCB is better as a baseline adhesive. It was because although wafer pairs bonded using $Flare^{TM}$ has a higher bond strength than those using BCB, wafer pairs bonded using BCB is still higher than that at the interface between Cu and porous low-k interlevel dielectrics (ILD), indicating almost 100% of bonded area routinely.

• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.330-335
• /
• 2018

A new approach for the fabrication of organic-organic conducting composite thin films using simultaneous co-vaporization vapor phase polymerization (SC-VPP) of two or more monomers that have different polymerization mechanisms (i.e., oxidation-coupling polymerization and radical polymerization) was reported for the first time. In this study, a PEDOT-PSMA composite thin film consisting of poly(3,4-ethylenedioxythiophene)(PEDOT) and poly(styrene-co-maleic anhydride)(PSMA) was prepared by SC-VPP process. The preparation of organic-organic conductive composite thin films was confirmed through FT-IR and $^1H-NMR$ analyses. The surface morphology analysis showed that the surface of PEDOT-PSMA thin film was rougher than that of PEDOT thin film. Therefore, PEDOT-PSMA exhibited lower electrical conductivity than that of PEDOT. But the conductivity can be improved by adding 2-ethyl-4-methyl imidazole as a weak base. The contact angle of PEDOT-PSMA was about $50^{\circ}$, as compared to $62^{\circ}$ for PEDOT. The demonstrated methodology for preparing an organic-organic conductive hybrid thin film is expected to be useful for adjusting intrinsic conductive polymer (ICP)'s surface properties such as mechanical, optical, and roughness properties.

• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.75-82
• /
• 2011

Five different composition UV-cured poly(urethane acrylate-co-acrylic acid) (PU-co-AA) films have been prepared by reacting isophorone diisocyanate(IPDI), polycaprolactone triol(PCLT), 2-hydroxyethyl acrylate(HEA), and different weight ratio trimethylolpropane triacrylate(TMPTA) and acrylic acid(AA) as diluents, and characterized using a Fourier transform infrared spectroscopy(FT-IR). The adhesion properties onto the stainless steel, morphology, mechanical hardness, and electrical property of UV-cured PU-co-AA films were investigated as a function of acrylic acid(AA) content. All the PU-co-AA films are structure-less and the molecular ordering and packing density decreased with increasing content of AA due to the flexible structure and -COOH side chains in AA. The crosscut test showed that PU-co-AA films without AA and with low content of AA showed 0% adhesion(0B) and the adhesion of PU-co-AA films in the range of 40-50% AA increased dramatically as the content of AA increases. The pull-off measurements showed that the adhesion force of PU-co-AA films to stainless steel substrate varied from 6 to 31 kgf /$cm^2$ and increased linearly with increasing AA content. The mechanical hardness also decreased as the content of AA increases. This may come from relatively linear and flexible structure in AA and low crystallinity in PU-co-AA films with higher content of AA. The higher AA-containing PU-co-AA films showed higher dielectric constant due to the increase of polarization by introducing AA monomer. In conclusion, the physical properties of UV-cured PU-co-AA films are strongly dependent upon the content of AA and the incorporation of AA in polyurethane acrylate is very useful way to increase the adhesion strength of UV-curable polymers on the stainless steel substrate.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.223.2-223.2
• /
• 2010

용융탄산염 연료전지(MCFC)는 $650^{\circ}C$에서 작동하는 고온형 연료전지 시스템이다. 이 시스템은 천연가스 등을 개질하여 생산된 수소를 바로 전기로 생산할 수 있는 시스템으로 열효율이 높으며, 현재 대체 발전시스템으로 각광을 받고 있다. MCFC는 개질방식에 따라 내부개질 방식과 외부개질 방식이 있다. 내부개질 방식은 수소를 생산하는 개질기가 스택내부에 장착된 형식으로 천연가스를 스택내부에서 개질하여 바로 전기를 생산하는 방식이다. 이 내부개질반응에 사용되는 촉매로는 알루미나에 담지된 니켈(Ni) 계열촉매이 주로 쓰이고 있다. 또한 내부개질촉매의 형태는 작은 원주형의 촉매형태로 성형되어 사용된다. 이 성형된 촉매의 크기가 바로 내부개질 스택의 크기를 결정하는 중요한 요소이다. 그래서 촉매의 크기는 되도록이면 작게 성형하는 것이 중요하다. 그러나 촉매의 크기가 너무 작으면 촉매를 성형하는데 큰 어려움이 생기게 된다. 본 연구에서는 니켈 촉매를 공침법이 아닌 균일용액침전법을 이용하여 제조하였으며, 이 촉매를 이용하여 지름이 약 2 mm 이하로 촉매를 압출성형하는 방법을 연구하였다. 먼저 요소(urea)를 이용한 균일용액침전법으로 촉매를 제조하였다. 최적의 촉매 합성조건을 살펴보기 위해서, 반응 온도를 80, 85, 90, 95, $100^{\circ}C$로 변화 시키면서 제조된 촉매의 특성을 살펴보았다. 그리고 촉매의 적절한 니켈 양을 알아보기 위해서 니켈의 양을 30, 40, 50, 60, 70 wt%로 변화 시켰으며, 조촉매로 사용되는 MgO 양을 5, 10, 15, 20 wt%로 변화 시켜서 제조된 촉매의 특성을 살펴보았다. 물성을 비교하기 위해서, X-선 회절분석(XRD) 및 TPR, 물리화학흡착을 하였다. 그 결과 침전반응온도가 $80^{\circ}C$에서 촉매가 가장 좋은 물성을 보였으며, 우수한 개질성능을 보였다. 그리고 촉매 활성물질인 니켈의 함량은 50 wt% 정도가 가장 적절한 함량이었으며, MgO의 함량이 15 wt%일 때 가장 우수한 물성과 개질 성능을 보여주었다. 이 촉매들은 공침법으로 제조된 상용촉매와 비교하였을 때, 보다 우수한 물성과 개질성능 보였다. 그래서 이 촉매를 균일침전법을 이용하여 대량으로 제조한 다음 압출성형 방법을 이용하여 촉매를 원주형으로 제조하였다. 먼저 제조된 촉매는 별도의 분쇄작업(볼밀 혹은 제트밀)을 거치지 않아도 입자사이즈가 약 $4{\mu}m$ 수준이 나오도록 촉매 제조조건을 조절 하였다. 그리고 소량의 Methyl cellulose(MC) 바이더와 물만 사용하여 촉매를 혼합한 다음 스크류 압출기를 이용하여 촉매를 성형하였다. 이 촉매는 지름이 약 2 mm 이하로 제조할 수 있었으며, 기계적 강도는 타정기로 성형한 상용촉매보다 우수하였다. 그리고 촉매 성능 또한 상용촉매와 비교하였을 때, 우수한 성능 보였다. MCFC용 내부개질 촉매로 균일용액침전법을 사용한 촉매가 적합하다고 판단되며, 압출성형에도 적합하다고 판단되었다.

• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.575-586
• /
• 2001

Stabilized polyacrylonitrile (PAN) fibers can be transformed into quasi-carbon fibers with different properties depending on heat-treatment processing parameters at lower temperatures than temperature for the fabrication of carbon fibers. It has been investigated from the preliminary work that appropriate quasi-carbonization processes at about 1100$^{\circ}C$ strongly influence various properties of quasi-carbon fiber/polymer composite as well as quasi-carbon fiber itself. The objective of the present work is to prepare quasi-carbon fibers from stabilized PAN fibers using various quasi-carbonization cycles and to examine their properties. Two temperature regions, up to 800$^{\circ}C$ and above 1000$^{\circ}C$, were used for quasi-carbonization processes. The chemical composition, physical properties, thermal stability, microstructure, mechanical properties and electrical resistivity of the quasi-carbon fibers prepared with different final heat-treatment temperatures, heating rates, holding times, heating steps, and purging gas purity were extensively examined. The results were also compared with those from stabilized PAN fiber and commercial PAN-based carbon fiber. The present study showed that a variety of properties of quasi-carbon fibers significantly depended on several quasi-carbonization process parameters.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.91-97
• /
• 2012

Recently, the performances of electrical and electronic devices are improving while the sizes are becoming smaller. As sound-generating systems, the two-dimensional speakers have been developed in place of conventional three-dimensional ones. Piezoelectric materials show the mechanical vibrations due to the voltage applied from outside the materials. The early film speakers had a limitations of output power in that it was not easy to make the conducting macromolecular films on the surfaces of the materials due to the internal chemical properties of materials. We have adopted the corona surface treatment in order to improve the output characteristics by increasing the adhesion of the coating material on to the surface of the center material of piezo film. The results showed the improvement of output power in the wider range of operating frequencies.