• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.290-296
• /
• 2009

We report on the effects of mixing of powders with various particle sizes on fracture toughness and wear resistance of thermally sprayed WC-10Co-4Cr coating layers fabricated by HVOF (high-velocity oxygen fuel) process. The size and the mixing ratio of powders were changed in order to get high fracture toughness and wear resistance. The mixing of small amount of coarse powders with fine powders resulted in the highest fracture toughness and wear resistance due to the lowest porosity in coating layers.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.6
• /
• pp.519-527
• /
• 2021

In this study, an electromagnetic pulse shielding effect was obtained by applying the arc metal spraying method to the ordinary concrete. For this study, to evaluate the electrical properties in the thickness of the metal sprayed coating, 8 types of metals(Cu, CuAl, CuNi, CuZn, Al, Zn, ZnAl, AlMg) were sprayed as coatings with a thickness of 100, 200 and 500㎛. The electrical conductivity on the surface was measured with a 4-pin probe, and an electromagnetic wave shielding effect test was performed according to KS. Based on the test results, 200 ㎛ was proposed as an optimal metal coating thickness for electromagnetic pulse shielding, and it was thermally sprayed on a 300×300×100mm concrete specimen to analyze the electromagnetic wave shielding performance. However, in the area of adhesion strength, the maximum was 1.11MPa, which was found to be less than 74% of the target performance.

• Resources Recycling
• /
• v.26 no.2
• /
• pp.56-65
• /
• 2017

This study is an experimental study on the corrosion protection performance according to the configuration ratio of the Zn and Al. A metal spraying was used as the arc metal spraying method, a specimen was produced by varying the proportion ratio and coating thickness of the Zn and Al. Experimental methods visually observed to corrosion of the specimen for 1, 3, 7, 15 days was conducted in accordance with the CASS salt spray test. This study has confirmed that the performance of the corrosion protection improved against the increase in the Al content. Further, it was confirmed that excellent perfomance is exhibited when the coating thickness is secured over $80{\mu}m$. In addition, the SEM analysis was performed to observe the cross-sectional shape of the metal spraying specimen after CASS testing. The analysis result showed that the deterioration of the metal spraying coating layer was reduced as the Al content increases.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.61-68
• /
• 2019

As the pollution of water resources deteriorates due to industrialization and urbanization, it is difficult to supply clean water through a water treatment method using chlorine. Therefore, the introduction of advanced water treatment facilities using ozone is on the increase. However, epoxy which is used as waterproofing and anticorrosives and stainless steel used in conventional waterproofing and anti-corrosive methods have deteriorated because of the strong oxidizing power of ozone, causing problems such as leaking. Moreover, it even causes the durability degradation of a concrete. Therefore, in this study, metal spraying system was used as the means of constructing a metal panel with excellent ozone resistance and chemical resistance which is an easier method than an existing construction method. Ozone resistance was evaluated in accordance with the type of metal sprayed coatings to develop a finishing method which can prevent the concrete structure of water treatment facilities from deterioration. Furthermore, electrochemical stability in actual sewage treatment plant environment was evaluated. Experimental results showed that Ti has superior ozone resistance after spraying and the electrochemical stability in the sewage treatment plant environment showed that Ti has the highest polarization resistance of $403.83k{\cdot}{\Omega}{\cdot}cm^2$, which ensures high levels of durability.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.5
• /
• pp.21-29
• /
• 2010

Cathodic Protection has been introduced as a method of protecting metals under the ground or sea from corrosion. Since 1970, it has been applied to reinforced concrete structures as a corrosion protection method. After 1990, it became used around the world, and its usability has been well confirmed. But this method has some problems in terms of construction and economy. To solve these problems, a Cathodic Protection Method using a highly-durable metal spray was developed. First, the specimen was covered with anodic materials (Zn, Al) by using metal spray. The corrosion protection performance was confirmed by measuring the corrosion current of the specimen. Through the experiment, it is possible to confirm that the Cathodic Protection Method using a high metal spray provides effective protection against corrosion to reinforced concrete structures.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.96-97
• /
• 2014

The purpose of this study is to analyze the adhesion strength of metal spray coating system in steel using high-frequency arc metal spray method. For the purpose the experimental factor such as surface roughness was selected at 3 levels. As a result of experiment, it appeared that high-frequency arc metal spray method had higher adhesion strength than existing metal spray method. Especially, Al-Mg showed the highest adhesion strength than other metals. In case of surface roughness, the higher roughness steel has, the higher adhesion strength appeared.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.94-95
• /
• 2014

The purpose of this study is to evaluate the corrosion protective property of Al-Mg high-freqeuncy arc metal spray method in comparison to Zn-Sn and Zn-Al alloys by electrochemical method and CASS test. As a result, it appeared that Al-Mg alloy had very higher corrosion protective property through the electrochemical characteristic and the CASS test comparing with the other alloys.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.89-90
• /
• 2022

Arc metal spraying is a widely used method for improving the performance of construction structures such as corrosion resistance and electromagnetic wave shielding. However, when arc metal spraying is applied to a concrete structure, adhesion performance may deteriorate. Therefore, the effect of each surface treatment method on the physical properties between the arc metal spray coating and concrete was reviewed by evaluating the deposition efficiency and adhesion performance according to the arc metal spray surface treatment method (surface reinforcing agent, roughening agent, and sealing agent). As a result, it is suggested as an optimal surface treatment condition to induce non-interface failure by using a roughening agent and to improve the properties of concrete and metal coatings by applying a surface reinforcing agent and sealing agent.

• Journal of Surface Science and Engineering
• /
• v.29 no.1
• /
• pp.15-25
• /
• 1996

자동차엔진의 피스톤-링에 응용할 목적으로 플라즈마 용사 기술로 피막한 몰리부덴늄 및 코발트 합금 피막 층의 마모성질을 비교 조사하였다. Ball-on-disc 형태의 마모기를 사용하여 상온 및 대기 중에서의 마모 및 마찰거동에 대하여 조사하였다. 용사 층의 미세경도 시험도 행하였으며, 용사층의 결정구조를 알기 위해 용사층을 x-선 회절 방법으로 분석하였다. 주사전자현미경을 사용하여 마모면의 표면 형상을 관찰하였다. 여러 용사조건으로 만든 용사층의 미세경도치와 마모거동과의 상관관계를 이해하려고 시도하였다. 주사전자현미경과 EDX를 사용하여 마모시 화학반응층과 마모기구를 규명하고자 하였다. 모리부덴늄 및 코발트 합금 분말을 각각 플라즈마 용사층의 단면을 관찰하여 마모기구을 비교하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.208.1-208.1
• /
• 2014

반도체 공정이나 디스플레이 공정에는 세라믹 부품이나 금속 부품이 많이 포함되어 있는데 이들 부품이 공정중에 발생하는 플라즈마 또는 여러가지 부산물에 의하여 부품의 표면에 다양한 코팅층이 형성된다. 그리고 이러한 공정에 들어가는 부품은 플라즈마 또는 각종 산에 취약한 특성을 나타내는데 이에 대하여 해결하기 위하여 세라믹 부품의 표면에 용사코팅이나 각종 물리, 화학적 방법을 이용하여 표면에 코팅층을 형성한다. 이렇게 형성된 코팅층중 특히 용사코팅에 의하여 형성된 코팅층은 플라즈마 공정이나 각종 부식성 산에 의하여 박리 또는 크랙이 발생하게 된다. 이러한 특성은 용사코팅층의 특성상 발생하고 있는 물리적 흡착에 의하여 흡착된 계면에서 박리가 발생할 가능성이 크게 된다. 이러한 현상을 줄이기 위하여 고열원을 통하여 열처리 실험을 실시한다. 특히 전자빔이나 레이저 열원은 고온 급속 가열에 의하여 고융점인 세라믹 용사코팅층 및 금속 코팅층을 재용융 및 응고과정을 통하여 미세구조를 변화시킨다. 특히 전자빔 열처리는 진공중에서 코팅층의 열처리를 행함으로써 코팅층 내에 있는 기공을 제거하거나 불순물을 제거하기에 용이하다. 본 연구에서 수행된 열처리는 기 코팅된 세라믹이나 금속재의 표면을 다량의 Electron의 Flux를 통하여 표면의 온도를 Melting point 직하 온도까지 상승하였다가 응고시킴으로써 코팅층의 특성을 변화시켰다. 이렇게 열처리된 시험편의 XRD를 통해 결정구조를 파악하고, SEM, OM을 통하여 기공의 제거, 결함의 제거 등을 확인하였으며 경도 변화를 통하여 물리적 특성의 변화를 함께 확인하였다. 평가 결과 결정구조의 변화와 더불어 경도등의 상승효과가 발생하였으며 코팅층 내에 존재하는 결함이 감소함을 확인하였다.