• Geophysics and Geophysical Exploration
• /
• v.5 no.4
• /
• pp.299-308
• /
• 2002

We have derived an analytical expression for the sensitivity of the frequency domain small-loop electromagnetic (EM) surveys over a two-layer earth in order to estimate the depth of investigation with an instrument having the source-receiver separation of about 2 m. We analyzed the sensitivities to the lower layer normalized by those to the upper half-space and estimated the depth of investigation from the sensitivity analyses and the mutual impedance ratio. The computational results showed that the in-phase components of the sensitivity to the lower layer dominates those to the upper layer when the thickness of the upper layer is less than 20 m, while the quadrature components are not sensitive to the lower layer over the entire frequency range. Hence we confirmed that the accurate measurement of the in-phase component is essential to increase the depth of investigation in the multi-frequency small-loop EM survey. When conductive basement of 10 ohm-m underlies the upper layer of 100 ohm-m, an accurate measurement of the in-phase components ensures the depth of the investigation more than 10 m even accounting a noise effect, from which we conclude that the small-loop EM survey is quite effective in imaging the conductive plume down to a considerable depth. On the other hand, in the presence of the resistive basement of 1,000 ohm-m, the depth of investigation may not exceed 5 m considering the instrumental accuracy, which implies that the application of the small-loop EM survey is not recommended over the resistive environment other than detecting the buried conductor.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.1
• /
• pp.27-32
• /
• 2011

The electorchemical properties of $Li_4Ti_5O_{12}$ added with Cr was tested. The addition or substitution of atoms to $Li_4Ti_5O_{12}$ are expected to modify the crystal structure, and therefore to change the electrochemical performances of $Li_4Ti_5O_{12}$. After the spinel structure $Li_4Ti_{5-x}Cr_xO_{12}$ (x = 0~0.2) were obtained via sol-gel method, the gel was heated in a muffle furnace at $800{\sim}850^{\circ}C$ for 12 h in air. The physical properties of the samples were characterized by TG-DTA, XRD, SEM, FT-IR, and the electrochemical properties were tested with battery cycler at 0.01~2.0 V range. The $Li_4Ti_5O_{12}$ exhibited 169.9 mAh/g at 1C and capacity recovery was 97.5% of the initial capacity at 0.1C. $Li_4Ti_{4.9}Cr_{0.1}O_{12}$ (Cr 1% added) showed best performance of 193.8 mAh/g at 1C and the capacity recovery was increased to 98.8% of the initial capacity at 0.1C.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.125-125
• /
• 2010

극성 [0001] 방향으로 성장된 질화물 기반의 LED (light emitting diode) 는 분극현상에 의해 발생하는 강한 내부 전기장의 영향을 받게 된다. 이러한 내부 전기장은 양자우물 내의 전자와 정공의 공간적 분리를 야기하고 quantum confined Stark effect (QCSE)에 의한 발광 파장의 적색 편이가 발생하며 양자효율의 저하를 가져오게 된다. 이러한 문제를 해결하기 위해 InGaN/GaN이나 AlGaN/GaN 양자 우물구조를 GaN의 m-plane (1$\bar{1}$00) 이나 a-plane (11$\bar{2}$0) 등 비극성면 위에 성장하려는 시도를 하고 있다. 그러나 비극성 면의 비등방성 (anisotropy) 으로 인하여 결정성이 높은 비극성 GaN을 성장하는 데에는 많은 어려움이 있다. GaN 층의 표면을 평탄화하고 결정성을 향상시키기 위해서 저온 GaN 또는 AlN 버퍼층을 성장하는 2단계 방법이나 고온 버퍼층을 이용하여 성장하는 연구들이 많이 진행되고 있다. 본 연구에서는 고온 GaN 버퍼층을 이용하여 기존의 2단계 성장과정을 단순화한 비극성 a-plane GaN을 r-plane 사파이어 기판위에 유기금속 화학증착법 (MOCVD)으로 성장하였다. 사파이어 기판위에 AlN 층을 형성하기 위한 nitridation 과정 후 1030 도에서 두께 45 ~ 800 nm의 고온 GaN 버퍼층을 성장하고 총 박막 두께가 2.7 ~ 3 um 가 되도록 a-plane GaN을 성장하여 표면 양상의 변화와 결정성을 확인하였다. 또한 a-plane GaN 박막 성장 시에 성장 압력을 100 ~ 300 torr 로 조절하며 박막 성장의 변화 양상을 관찰하였다. 고온 GaN 버퍼층 성장 두께가 감소함에 따라 결정성은 증가하였으나 표면의 삼각형 형태의 pit 밀도가 증가함을 확인하였다. 또한 성장 압력이 감소함에 따라 표면 pit은 감소하였으나 결정성도 감소하는 것을 확인하였다. 성장 압력과 버퍼층 성장 두께를 조절하여 표면에 삼각형 형태의 pit이 존재하지 않는 RMS roughness 0.99 nm, 관통전위밀도 $1.78\;{\times}\;10^{10}/cm^2$, XRD 반가폭이 [0001], [1$\bar{1}$00] 방향으로 각 798, 1909 arcsec 인 a-plane GaN을 성장하였다. 이 연구를 통해 고온 GaN 버퍼 성장방법을 이용하여 간소화된 공정으로 LED 소자 제작에 사용할 수 있는 결정성 높은 a-plane GaN을 성장할 수 있는 가능성을 확인하였다.

• Resources Recycling
• /
• v.32 no.6
• /
• pp.45-53
• /
• 2023

This study discussed the trend and future strategy of adsorption technology R&D to effectively recover ammonia emitted from the livestock fields. A proper ammonia adsorbent should incorporate acidic or hydrogen bonding functional groups on the surface, as well as a high specific surface area and a good surface structure appropriate for ammonia adsorption. Activated carbon and minerals such as zeolite have widely been used as ammonia adsorbents, but their adsorption effects are generally low, so any improvement through surface modification should be necessary. For example, incorporation of metal chloride included in a porous adsorbent can promote ammonia adsorption effectiveness. Recently, new types of adsorbents such as MOFs (Metal-Organic Frameworks) and POPs (Porous Organic Polymers) have been developed and utilized. They have shown very high ammonia adsorption capacity because of adjustable and high specific surface area and porosity. In addition, Prussian Blue exhibited high ammonia adsorption and desorption performance and selectivity. This looks relatively advantageous in relation to the recovery of ammonia from livestock waste discharge. In the future, further research should be made to evaluate ammonia adsorption/desorption efficiency and purity using various adsorbents under conditions suitable for livestock sites. Also, effective pre- and/or post-treatment processes should be integrated to maximize ammonia recovery.

• Journal of Korea Port Economic Association
• /
• v.31 no.4
• /
• pp.75-89
• /
• 2015

This study examines 31 import and export cargo items handled in each port to investigate which items face the most competition among the ports and how many of them are transited to other ports. The study aims to suggest implications for the future port policy of Incheon Port. It was found that the volume concentration in the Western Coast region from 2005 to 2014 became increasingly decentralized. The decentralization began in earnest in 2009 in particular, and the value was 0.448 in 2014, indicating fierce competition among the regions. According to the static and dynamic positioning analyses results for Incheon Port, Pyeongtaek and Dangjin Port, and Gunsan Port, using BCG Matrix, the static positioning analysis showed that Incheon Port belongs to the 3rd quadrant (Cash Cows), Pyeongtaek and Dangjin Port belongs to the 2nd quadrant (Question Marks), and Gunsan Port belongs to the (Dogs) group. This implies that Incheon Port has maintained its position with large shares compared to those of other ports, despite its low growth rate. However, the market position and growth rate of Incheon Port decreased according to the dynamic positioning analysis results. The shift-share analysis results indicated that the volumes of Incheon Port and Gunsan Port were shifting to Pyeongtaek and Dangjin Port. Moreover, the ratio of absolute growth to potential growth of Incheon Port and Gunsan Port turned out to be significantly lower than that of Pyeongtaek and Dangjin Port, implying that Incheon Port and Gunsan Port are declining as compared to Pyeongtaek Port and Dangjin Port. According to the LQ index analysis results, specialized items from Incheon Port that do not overlap with other ports included the following ten items: meat, fish and crustaceans, bituminous coals, crude oil and petroleum, petroleum-refined products, plastic rubber and products, textiles, nonferrous metal and products, electric machinery, and aircrafts and ships. In particular, it was confirmed that the bulk cargo of Incheon Port was actually shifting to Pyeongtaek and Dangjin Port following the policy of re-establishing port functions.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.477-483
• /
• 2008

$La_{0.7}Sr_{0.3}Co_{0.2}Fe_{0.8}O_{3-{\delta}$ oxide was synthesized by a citrate method and a typical dense membrane of perovskite oxide has been prepared using as-prepared powder by pressing and sintering at $1300^{\circ}C$. Precursor of $La_{0.7}Sr_{0.3}Co_{0.2}Fe_{0.8}O_{3-{\delta}$ prepared by citrate method was investigated by TGA and XRD. Metal-citrate complex in precursor was decomposed into perovskite oxide in the temperature range of $260{\sim}410^{\circ}C$ but XRD results showed $SrCO_3$ existed as impurity at less than $900^{\circ}C$. Electrical conductivity of membrane increased with increasing temperature but then decreased over $700^{\circ}C$ in air atmosphere ($Po_2=0.2atm$) and $600^{\circ}C$ in He atmosphere ($Po_2=0.01atm$) respectively due to oxygen loss from the crystal lattice. The oxygen permeation flux increased with increasing temperature and maximum oxygen permeation flux of $La_{0.7}Sr_{0.3}Co_{0.2}Fe_{0.8}O_{3-{\delta}$ membrane with 1.6 mm thickness was about $0.31cm^3/cm^2{\cdot}min$ at $950^{\circ}C$. The activation energy for oxygen permeation was 88.4 kJ/mol in the temperature range of $750{\sim}950^{\circ}C$. Perovskite structure of membrane was not changed after permeation test of 40 h and the membrane was stable without secondary phase change with 0.3 mol Sr addition.

• Applied Chemistry for Engineering
• /
• v.27 no.6
• /
• pp.583-589
• /
• 2016

Lubricant additives including zinc dialkyldithiophosphate (ZDDP) containing metal have been widely used due to the advantage of very low cost, but they can generate impurities such as ash. In this work, ZDDP containing metals was partially replaced with bis[3-(dialkyloxyphosphorothionyl) thio-2-methylpropanyloxy] butane (BAP4s) which was synthesized conveniently and effectively from alkanediol without any metal components. Also, the wear resistance property of synthesized BAP4s were studied. Wear scar diameter (WSD) values of BAP4s with butyl, octyl, decyl, dodecyl or tetradecyl groups were also measured by four-ball test. As the length of the alkyl group increased from 4 to 8, the WSD value of BAP4s decreased rapidly from 0.59 to 0.45 mm, but from 8 to 14, the value increased very slowly from 0.45 to 0.50 mm. Thus, among all BAP4s, B8P4 having BAP4 with the octyl group, showed the lowest WSD value. Furthermore, the WSD values were measured in a lubricant base oil mixed with a 0.50 percent concentration (w/w) of either BAP4 or ZDDP. The former was 0.55 mm, and the latter was 0.45 mm. The thermal stability and tribofilm formation peroperty were also measured by thermogravimetric analyzer (TGA) and energy-dispersive X-rays spectroscopy (EDS), respectively.

• Journal of Preventive Medicine and Public Health
• /
• v.21 no.2 s.24
• /
• pp.224-237
• /
• 1988

To determine the causes of and related factors to childhood injuries, the emergency room records and inpatient medical records were reviewed for 4,849 injured children out of 15,790 pediatric patients(<15 years old) who visited the emergency rooms of 3 university hospitals and 2 general hospitals in Taegu from 1 January to 31 December 1987. Out of total injured children, 54.675 were 3-8 years old and the male to female ratio of the total injured children was about 2:1. The leading causes of injury were falls and slips (29.1%) and traffic accident(28.2%). The frequency of injury was higher in May-October than the rest of months and 51.6% of the injuries occurred between 15 and 20 o'clock. Falls and slips took place most frequently at the stairway(25.7%). The most common interpersonal violence was inflicted injuries(85.6%) and there were 11 child rapes. Dog bites accounted for 67.6% of all biting injuries and it occured 2.9 times more in male than in female. CO intoxication was the most common cause of poisoning (45.3%) and scalding accounted for 85.2% of all burns. Common places of drownings were river (32.2%), swimming pool (22.6%) and construction site(19.3%). To prevent childhood injuries, it is recommended to eliminate the hazardous environmental factors, to provide safe playgrounds, to educate the children for safety from kindergarten and the general public through mass communication, to establish a strict safety standard for houses, public buildings and facilities, and playgrounds.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.4
• /
• pp.63-73
• /
• 2009

Recently, the use of lightweight panels in building structures has been increasing. Of the various lightweight panel types, styrofoam sandwich panels are inexpensive and are excellent in terms of their insulation capacity and their constructability. However, sandwich panels that include organic material are quite vulnerable to fire, and thus can numerous casualties in the event of a fire due to the lack of time to vacate and their emission of poisonous gas. On the other hand, lightweight foamed concrete is excellent, both in terms of its insulation ability and its fire resistance, due to its Inner pores. The properties of lightweight concrete is influenced by foaming agent type. Accordingly, this study investigates the insulation properties by foaming agent type, to evaluate the possibility of using light-weight foamed concrete instead of styrene foam. Our research found thatnon-heating zone temperature of lightweight foamed concrete using AP (Aluminum Powder) and FP (animal protein foaming agent) are lower than that of light-weight foamed concrete using AES (alkyl ether lactic acid ester). Lightweight foamed concrete using AES and FP satisfied fire performance requirements of two hours at a foam ratio 50, 100. Lightweight foamed concrete using AP satisfied fire performance requirements of two hours at AP ratio 0.1, 0.15. The insulation properties were better in closed pore foamed concrete by made AP, FP than with open pore foamed concrete made using AES.

• Journal of Preventive Medicine and Public Health
• /
• v.15 no.1
• /
• pp.187-196
• /
• 1982

The followings are the results of the study on industrial accidents occurred at 12 factories manufacturing metal products during the period of 2 years from January 1980 to December 1981 in the area of Yong-Dung-Po in Seoul. The results of the study are as follows: 1. The incidence rate of industrial injuries was 45.7 per 1,000 workers of the sample group and the rate of male (54.0) was three times higher than that of female (17.5). 2. In age groups, the highest rate was observed in the group of under 19 years old with 83.5, while the lowest in the group of 40s. 3. It was found that those who had short term of work experience produced a higher rate of injuries, particularly, the group of workers with less than 1 year of experience showed the highest rate of it as 48.1%. 4. In working time, the highest incidence rate occurred 3 and 7 hours after the beginning of their working showing the rate of 6.0 and 6.1 per 1,000 workers, respectively. 5. The highest incidence rate was observed on Monday as 8.4 per 1,000 workers, and it was 18.3% in aspect of the days of a week. 6. In aspect of the months of a year, the highest incidence was observed on July 1,000 workers and the next was on March as 4.8. These figures account for 11.8% of total occurrence in respective month. as 5. 4 per and 10.5% 7. In causes of injuries, the accident caused by power driven machinery showed the highest rate with 37.5%, the second was due to handling without machinery with 17.2%, and the third was due to falling objects with 14.2%, and striking against objects with 10.2%, and so on. 8. By parts of the body affected, the most injuries 84.3% of them occurred on both upper and lower extremities with the rate of 58.8% for the former and 25.5% for the latter. Fingers were most frequently injured with a rate of 40.3%. Comparing the sites of extremities affected, rate of injuries on the right side was 55.0% and 45.0% on the left side. 9. In the nature of injury, laceration and open wound were the highest with 34. 0%, the next was fracture and dislocation with 31. 9%, and sprain was the third with 8.1%. 10. On the duration of treatment, it lasted less than one month in 68.9% of the injured cases, of which 14.5% of the cases were recovered within 2 weeks, and 54.4% of them were treated more than 2 weeks. And the duration of the treatment tended to be prolonged in larger industries. 11. The ratio of insured accidents to uninsured accidents was 1 to 4.7.