• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1145-1151
• /
• 2015

High pressure components of a gas turbine engine must operate for a long life under severe conditions in order to maximize the performance and minimize the maintenance cost. Enhanced cooling design, thermal barrier coating techniques, and nickel-base superalloys have been applied for overcoming them and furthermore, material modeling, finite element analysis, statistical techniques, and etc. in design stage have been utilized widely. This article aims to evaluate the effects on the low cycle fatigue life of the high pressure turbine nozzle caused by different turbine inlet temperature profiles and installation conditions and to investigate the most favorable operating condition to the turbine nozzle. To achieve it, the structural analysis, which utilized the results of conjugate heat transfer analysis as loading boundary conditions, was performed and its results were the input for the assessment of low cycle fatigue life at several critical zones.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.254-262
• /
• 1998

Multilayer Langmuir-Blodgett (LB) films coated on quartz crystal microbalance (QCM) of octa-substituted metallophhtalocyanines ($MPc(OEH)_8$, M = Cu, Co, and Sn) and dihydrogen phthalocyanines ($H_2Pc(OEH)_8$) were used to quantify $NO_2$ concentrations. They were exposed to various concentrations of $NO_2$ in dry $N_2$. Among the four phthalocyanines we tested, the metal-free $H_2Pc(OEH)_8$ was observed to be most sensitive to $NO_2$. However, its LB film showed a partially irreversible behavior, that is part of the frequency change due to $NO_2$ adsorption could not be recovered even after purging with pure $N_2$ gas for an extended period. Examining the spectra of NMR and FTIR revealed fact that the irreversible portion of frequency change was due to ether groups in the linkage between side chains and the Pc unit. In order to remove the effect of such initial deactivation, on $NO_2$ quantification experiment, a freshly fabricated LB film was treated at a high concentration of $NO_2$ so that the ether sites were saturated. A pretreated LB film showed a reproducible performance for repeated uses. The $CuPc(OEH)_8$ LB film showed a satisfactory sensing performance down to as low as 4 ppm. For the $H_2Pc(OEH)_8$ LB film, the lower detection limit was found to be 35ppb of $NO_2$. In order to make the experimental condition more realistic, the carrier gas, dry nitrogen, was replaced by air. It was observed that the presence of oxygen, a weak electron acceptor, reduced the sensitivity and thus increased the sensing limit to hundreds of ppb. Results of experiments with moisture added showed that the interference of moisture was quite severe.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.259-259
• /
• 2007

층상구조의 전이금속 산화물($LiMO_2$, M=Co, Ni, Mn)은 리튬이차전지용 양극재료로 활발한 연구가 진행되고 있다. 차세대 리튬이차전지 시스템의 개발 및 고성능화를 위해서는 전지의 용량을 결정하는 핵심 부품인 양극재료의 고용량화 및 고안정화는 필수 불가결하다. 따라서 본 연구에서는 상업적으로 큰 장점이 있는 고상반응 공정을 이용하여 리튬이차전지용 양극소재를 제조하고, 소재의 전기화학적, 구조적인 특성을 평가하였으며, 다음과 같은 주제를 가지고 연구를 진행하였다. $LiCoO_2$ 양극재료는 리튬이온전지로 널리 사용되고 있다. 높은 에너지 밀도의 리튬이온전지를 얻기 위해서는 $LiCoO_2$ 양극재료가 고용량화 및 고밀도화를 가져야 한다. 여기서 $LiCoO_2$ 분말이 irregular particle morphology를 가지면 tap density가 $2.2-2.4gcm^{-3}$로 에너지 밀도가 낮으나, 구형 $LiCoO_2$의 정극재료는 tap density가 $2.6-2.8gcm^{-3}$로 상대적으로 energy density가 높아지는 효과가 있다. 구형 $LiCoO_2$ 양극재료를 합성하기 위해서는 chelating agent를 이용한 "controlled crystallization" 침전법을 사용하여 합성한 구형 코발트 수화물을 사용하고 있다. "controlled crystallization" 침전법에서 사용되는 chelating agent로는 주로 ammonia가 이용되고 있다. 본 연구에서는 chelating agent로 ethylene diamine을 사용하여 sodium hydroxides를 precipitation으로 침전 반응하여 구형 코발트 수화물을 합성하였다. 상기 방법으로 합성된 코발트 수화물과 리튬 수화물($LiOH{\cdot}H_2O$-고순도화학(高殉道化學))을 사용하여 고상법을 통하여 $LiCoO_2$를 합성하였다. 제조된 분말의 결정구조와 전기화학적 특성분석은 X-선 회절분석 및 리트벨트 구조정산, 그리고 충/방전 싸이클링을 수행하였으며, 분말의 미세구조 변화를 SEM을 이용하여 분석하였다.

• Applied Chemistry for Engineering
• /
• v.23 no.6
• /
• pp.554-560
• /
• 2012

Recently, it has been increasing trend to use conductive materials as electronics and communication technology in electronics industry are developing. The noble metal such as Ag, Pt, Pd etc. are mostly used as conductive materials, To reduce production cost, alternative materials with similar characteristics of noble metals are needed. Copper has advantages, i.e its electronic properties are similar to noble metals and low cost than noble metal, but its use has been restricted because of oxidation in air. In this study, the tin film was coated on copper by electroless plating to protect copper from oxidation and to confirm the effects of temperature, pH, amount of $SnCl_2$, and feeding speed in plating conditions. Additionally, we apply $Cu_{core}Sn_{shell}$ powder as conductive filler with low-temperature densification and analysis by SEM, XRD, FIB and 4-Point Probe techniques. As result of the study, tin film was coated well on copper and was protected from oxidation. After low-temperature densification treatment, the meted tin made chemical interconnections with copper. Accordingly, conductivity was increased than before condition. We hope $Cu_{core}Sn_{shell}$ powder to replace noble metals and use in the electronic field.

• Journal of Applied Biological Chemistry
• /
• v.61 no.4
• /
• pp.417-421
• /
• 2018

Ultraviolet rays are electromagnetic waves with a shorter wavelength than visible light, and ultraviolet rays that pass through the ozone layer are the main cause of skin aging. Chronic exposure of skin tissue to ultraviolet light activates the Mitogen-activated Protein Kinases (MAPKs) signaling pathways in human keratinocytes, resulting in increased production of matrix metalloproteinases (MMPs). In this study, we investigated the herbal extracts from Jeju Island on the anti-aging effect in human keratinocytes (HaCaTs) by ultraviolet stimulation. We examined that herb extract from Jeju Island were decreased in anti-aging activity on measuring the level of MMP-1 gene and protein expression in ultraviolet-induced keratinocytes. As a result, it was confirmed that Thymus quinquecostatus extract (TQE) significantly reduced the expression of MMP-1 in a dose-dependent manner by UV irradiated HaCaTs. According to our data, TQE significantly attenuated UV-induced phosphorylation of the MAPKs signaling elements ERK1/2, JNK1/2 and p38 proteins. These results suggest that the MAPKs pathway may contribute to the inhibitory effect of TQE on UV-induced MMP-1 production in human keratinocytes. Our results suggest that TQE may be a protective agent against skin aging by preventing UV-induced MMP-1 production.

• Applied Chemistry for Engineering
• /
• v.22 no.1
• /
• pp.67-71
• /
• 2011

The cathodic active material of $Li/SO_2Cl_2$ battery is $SO_2Cl_2$, which is the solvent of an electrolyte. It is referred to as a catholyte, a compound word of cathode and electrolyte. As the battery discharges, the catholyte burns out. And thus, the characteristics of the $SO_2Cl_2$ in the battery determine the capacity. In addition, the transition minimum voltage (TMV) and the voltage delay deviation of $Li/SO_2Cl_2$ battery are due to the passivation film formed by the reaction between an electrolyte and Li. Impurities in the electrolyte, such as moisture or heavy metal ions, will accelerate the growth of the passivation film. Therefore, a technology must be established to purify an electrolyte and to ensure the effectiveness of the purification method. In this research, $LiAlCl_4/SO_2Cl_2$ was manufactured using $AlCl_3$ and LiCl. Its concentration, the amount of moisture, and the metal amount were evaluated using an ionic conductivity meter, a colorimeter, and FT-IR.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.2
• /
• pp.73-77
• /
• 2024

The spinel-type oxide (Ni_x, Mn_y, Co_3-x-y)O₄ (NMC) is widely utilized as a material for temperature sensors with a negative temperature coefficient (NTC), finding applications across various industries including electric vehicle battery management systems. Typically, NMC is manufactured using solid-state reaction methods employing powders of Ni, Mn, and Co compounds, with the densification process through sintering recognized as a crucial factor determining the electrical properties of the temperature sensor material. In this study, NMC pellets were synthesized via solid-state reaction and their crystallographic and microstructural characteristics were investigated. Also, the activation energy for densification behavior during the sintering process was determined. According to the analysis results, the room temperature resistance of the NMC pellets was measured at 10.03 Kohm, with the sensitivity parameter, B-value, recorded at 3601.8 K, indicating their potential applicability as temperature sensors across various industrial fields. Furthermore, the activation energy for densification was found to be 273.3 ± 0.4 kJ/mol, providing valuable insights into the thermodynamic aspects of the sintering process of the NMC.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.1
• /
• pp.39-47
• /
• 2024

In this study, LiDAR-detective black material is synthesized by recycling silicon sludge (SS) that is generated from semiconductor manufacturing process, and its recognition is confirmed using two types of LiDAR sensors (MEMS and Rotating LiDAR). In detail, metal impurities on the surface of SS is removed, followed by coating of titanium dioxide (TiO₂) and subsequent chemical reduction to obtain SS-derived black TiO₂ (SS/bTiO₂) material. As-prepared SS/bTiO₂ is mixed with transparent paint to prepare hydrophilic black paints and applied to a glass substrate using a spray gun. SS/bTiO₂-based paint shows similar blackness (L^*=15.7) compared to commercial carbon black-based paint, and remarkable NIR reflectance (26.5R%, 905nm). Furthermore, MEMS and Rotating LiDAR have successfully detected the SS/bTiO₂-based paint. This is attributed to the occurrence of high reflection of light at the interface between the black TiO₂ and the silicon sludge according to the Fresnel's reflection principle. Hence, the new application field to effectively recycle silicon sludge generated in the semiconductor manufacturing process has been presented.

• The korean journal of orthodontics
• /
• v.28 no.2 s.67
• /
• pp.329-341
• /
• 1998

Sterilization has received much attention in orthodontic practices over the past several years. The present study was undertaken to investigate the effects of sterilization on the physical properties of orthodontic pliers-AEZ, Unitek, and Dentronix ligature cutters. This study was designed to examine the tips of ligature cutters before and after 200 and 400 sterilization cycles using the Bowmar RHT-1000, the Dentronix DDS-5000, and the Eschmann SES-2000. The tip surface and the fracture surface were observed with a scanning electron microscope. The microstructure was observed with an optical microscope. The hardness test was carried out with the mic개-Vickers hardness tester and the Rockwell C Scale hardness tester. The chemical composition was analyzed by energy dispersive X-ray spectrometer. The results of this study were as follows : 1. The number and the size of corrosion products on the tip surface and the proportion of cleavage planes in fractured specimen increased, but the hardness of the tip decreased in proportion to sterilization cycles. From these observations, it was considered that mechanical properities decreased in proportion to sterilization cycles. 2. The number and the size of chromium carbides increased in proportion to sterilization cycles. Coarse microstructure decreased mechanical properities. 3. The AEZ and Unitek ligature cutters were Fe-Cr stainless steels, but the Dentronix ligature cutter was Co-Cr alloy. There were many differences among manufactures, but the chemical composition was .not changed after sterilization cycles. 4. The tip edge of ligature cutter used in a clinic revealed microcracks with the SEM observation. Clinical experience confirmed that ligature cutters were gradually degraded by sterilization.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.32 no.1 s.55
• /
• pp.45-51
• /
• 2006

In the field of makeup cosmetics, especially, powder-based foundations such as two-way cake, pact and face powder, the quality of which is known to be strongly influenced by the properties of powder, surface treatment technology is widely used as a method to improve the various characteristics of powder texture, wear properties, dispersion ability and so on. The two-way cake or pressed-powder foundation is one of the familiar makeup products in Asian market for deep covering and finishing purpose. In spite of the relent progress in surface modification method such as composition of powders with different characteristics and application of a diversity of coating ingredient (metal soap, amino acid, silicone and fluorine), this product possess a technical difficulty to enhance both of the adhesion power and spreadability on the skin in addition to potential claim of consumer about heavy or thick feeling. This article is covering the preparation and coating method of nano-vesicle that mimic the double-layered lipid lamellar structure existing between the corneocytes of the stratum corneum in the skin for the purpose of improving both of two important physical characteristic of two-way cake, spreadability and adhering force to skin, and obtining better affinity to skin. Nano-vesicle was prepared using the high-pressure emulsifying process of lecithin, pseudo ceramide, butylene glycol and tocopheryl acetate. This nano-sized emulsion was added to powder-dispersed aqueous phase together with bivalent metal salt solution and then the filtering and drying procedure was followed to yield the nano-vesicle coated powder. The amount of nano-vesicle coated on the powder was able to regulated by the concentration of metal salt and this novel powder showed the lower friction coefficient, more uniform condition of application and higher adhesive powder comparing with the alkyl silane treated powder from the test result of spreadability and wear properties using friction meter and air jet method. Two-wav cake containing newly developed coated powder with nano-vesicle showed the similar advantages in the frictional and adhesive characteristics.