• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.2
• /
• pp.161-166
• /
• 2014

This Electromagnetic metal piece detection sensor, having high sensitivity even under high humidity and dust density, using LVDT was investigated. Metal detection characteristics using phase detection method, for 3 frequencies covering ELF and LF band, were experimentally measured. It was found that the sensitivity for metal and animal food, in which metal piece was included, was exponentially increased as frequency increased. Reducing cutoff frequency of LPF after PD was found to be effective to proportionally increase sensitivity. Also the sensitivity of metal piece detection was enhanced by optimizing BPF bandwidth and SNR. Metal piece detection limit using available ferrous test samples was found to be 0.7mm diameter from the experiment using 50kHz, in ELF band, which was known to have better selectivity to animal food. is an example of ABSTRACT format.

• Journal of the Korean Society of Radiology
• /
• v.9 no.5
• /
• pp.323-329
• /
• 2015

This study is aimed at assessing whether dynamic wedge filters are appropriate to be used instead of physical wedge filters. The X-ray energy generated from linear accelerator is commercialize 6 MV and 10 MV. $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, and $60^{\circ}$ of physical wedge filter was irradiated by dose rate 100, 200, 300, 400, 500, and 600 MU/min for each angle and for comparison with a dynamic wedge filter, irradiate 96 times under the same conditions. The measurement conditions are as 100 cm source-film distance and $10{\times}10cm$ irradiated surface. A developed film was scanned and analyzed after a calibration through a dose analysis program and the dose rate was compared after calculating the standard deviation. Dynamic wedge filters make dose, scattered rays and treatment time reduced and very useful due to less irradiated doses to patients. The errors at each dose rate under the same conditions were irrelevant. Thus, treatment based on a high dose rate depending on the patient is expected to be feasible.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2004.04a
• /
• pp.31-31
• /
• 2004

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2006.06a
• /
• pp.105-106
• /
• 2006

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.192-193
• /
• 2003

광학박막은 유리, 플라스틱, 실리콘, 금속 기판 등에서 표면의 반사율, 투과율, 흡수율과 편광상태 등의 광학적 특성을 변화시키기 위해 광학표면에 코팅을 하여 많이 사용하고 있으며, 파장영역으로는 수 nm의 연x선부터 자외선, 가시광선과 수십 $\mu$m의 적외선까지 적용할 수 있고, 광학기기에서는 대부분의 광학부품이 광학적 특성을 증진시키기 위하여 각각의 목적에 맞도록 코팅되어 있다. 광학코팅의 종류로는 단순한 무반사코팅으로부터 고반사코팅, 칼라필터, 간섭필터, 편광분리기코팅, 마이너스필터 등까지 매우 다양하다. (중략)

• Korean Journal of Optics and Photonics
• /
• v.19 no.6
• /
• pp.429-434
• /
• 2008

We propose a wavelength filter based on long-range surface plasmon-polaritons (LR-SPP) supported by a asymmetric doubleelectrode LR-SPP structure. For the case of the asymmetric double-layered LR-SPP waveguide, LR-SPPs exist with a much broader range of index mismatches between core and clad materials. Thus, the asymmetric double-electrode LR-SPP waveguide is adequate to form a plasmonic band-gap device as we report in this paper by studying Bragg-reflection wavelength filter based on it. The structure for wavelength filter operating telecommunications wavelength is designed by using the method of line (MoL) and the transfer matrix method. The fabricated device shows a relatively high extinction ratio of 50 dB with a bandwidth of 2 nm, and the performance is very consistent with numerical simulations.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.18.1-18.1
• /
• 2009

금속 다공체는 자동차, 선박, 건축 등의 분야에서 구조물이나 충격흡수제 등으로 응용되고 있는데 이들은 일반 금속 구조물에 비해 가볍고 플라스틱에비해서는 강한 장점을 지닌다. 현재 사용되고 있는 대부분의 금속 다공체는 발포 주조공정으로 제조된 알루미늄으로서, 철계 합금에 비해 가벼운 장점을 갖지만 강도가 상당히 떨어지고 가격이 높은 단점을 가진다. 따라서 본 연구에서는 알루미늄 대신 철계 합금으로 다공체를 제조하고자 하였고 제조방법으로는 주조공정 대신 분말공정을선택하였다. 분말공정은 구형 스티로폼을 금속분말 슬러리로 코팅한 후 스티로폼을 제거하여 낱개의 금속중공체(Metallic Hollow Sphere)를 제조하고 이렇게 제조된 중공체를 뭉쳐 성형함으로써최종 형상의 다공체를 제조하는 방법이다. 이 방법으로 제조된 다공체는 주조공정으로 제조된 다공체보다높은 강도를 나타내며 낱개의 중공체는 성형공정을 거치지 않고 필터나 충진재 등의 새로운 용도로 활용될 수 있다.

• 기계와재료
• /
• v.9 no.2 s.32
• /
• pp.134-144
• /
• 1997

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 1988.12a
• /
• pp.33-34
• /
• 1988

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2004.11a
• /
• pp.112-113
• /
• 2004