• 전기의세계
• /
• v.14 no.4
• /
• pp.22-27
• /
• 1965

우리나라의 speaker제작의 역사는 얼마되지 않을 뿐더러 자급자족의 영역을 못 벗어나고 있다. Weston speaker, 자사내에서 자급자족하고 있는 금성사제 speaker등 완전히 질량의 단계에 못들어가고 있는 실정이다. 그나마 성능면에서도 뒤떨어짐을 면할 수 없는 실정이다 .부속품 예컨데 자철 coil접착제등 거이 매매회사에서 직수입하고 있는 형편인것 같다. 물론 종합공업이 발달해야만 되겠기에 단편적 발달은 기하기 어려울 줄 안다. 그러나 speak의 조립 공정에서 끝마치고 있는 형편이고 보면 한심할 지경이다. 물론 speaker제작이라고 하는 것은 극히 delicacy한 면을 가지고 있다. 즉 효율은 $B^{2}$에 비례하는것은 당연하지만 효율을 높이고저 공기부하의 저항을 크게 할려면 corn의 입경이 크게 되므로 자연적으로 진동계의 질량이 크게되며 또 voice coil의 저항을 적게하자니 coil가 필연적으로 굵게되어 길이가 짧게 될 뿐만아니라 air gap 이 크게되어 자속밀도 B가 적게 되는 상반관계가 있다. Cabinet, baffle, corn, corrugation, speaker system등을 가장 합리적으로 설계할 필요가 있다. 이 실험결과를 보고함으로서 speaker연구에 대한 욕구를 갖고 의욕적인 계기가 되었으면 한다. Voice coil 의 turn수를 바뀌었을때 impedance을 측정하였으며 turn수와 음압level 및 주파수 관계를 알아보았다. 그리하여 중형 speaker의 주파수특성을 알아 설계에 기여하고저 한다.

• Journal of Korean Library and Information Science Society
• /
• v.43 no.1
• /
• pp.417-438
• /
• 2012

This study is carried out to investigate the printing culture in current Chollanamdo province. Searching the publication in Naju during the Chosun dynasty, 89 titles were found, where publication had begun from early Koryo dynasty. Active Publication was initiated from the era of King Jungjong and many books were published in 16th and 19th centuries. Many Confucian books were published dominantly in the first half of the Chosun dynasty, and collective literature and genealogical records in the later half. In the first half of the dynasty, most of books were published by the order of a king, the officer of province, or an individual, and, in the later half, increasingly collective literature and genealogical records were published by an individual or a family. Also woodblocks were used in the first half of the dynasty, wooden types in the later half.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.1
• /
• pp.1-9
• /
• 1986

This is the third part of the four-part paper describing the development of a packet-switched computer communication network named the KORNET. In this paper we describe the design and implementation of the X.25 protocol connecting packet mode data terminal equipments(PDTE's) with data circuit terminating equipments(DCE's). In the KORNET, the X.25 protocol has been implemented on the line processing module-A(LPMA) of the network node processor(NNP). In the implementation of X.25, we have divided the software module according to the service function, and have determined the the rules that interact between the modules. Each layer protocol has been developed using the technique of the finite state machine. Before the actual coding of softwares, we hafve used formal software development tools based on the specification and description language (SDL) and program design languate (PDL) recommended by the CCITT. In addition, for the efficient operation of the X.25 protocol system we have analyzed the system performance and the service scheduling method of each module. The results will also be given.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.6
• /
• pp.795-800
• /
• 1986

High value sheet resistance (Rs, 350\ulcorner/ -80K\ulcorner/) born implanted polysilicon resistors were fabricated under process conditions compatible with bipolar integrated circuits fabrications. This paper includes studies of sensitivity of Rs to doping concentration, the effect of thermal annealing temperature on Rs, temperature coefficient of resistance (TCR), the effect of polysilicon thickness on Rs and the Rs variation within a run and between runs.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.11a
• /
• pp.195-197
• /
• 2022

위성항법시스템(GPS)은 편리성, 활용도 등으로 인해 항법, 이동통신, 금융, 전력 등 여러 분야(측위·항법·시각)에서 사용하고 있다. 위성이 지구로부터 약 2만키로미터 떨어져 있어 위성신호 수신 세기가 약해 외부로부터 전파간섭이나 교란 등 보안에 취약한 단점이 있다. 주요국(미국, 유럽, 중국, 인도 등)은 보안을 강화하여 독자적인 위성항법 시스템을 구축하여 운영하고 있다. 우리나라도 지상기반(eLoran)과, 위성기반(KPS)의 항법시스템을 구축중이다. 시스템 구축이 완료되면 한층 강화된 국가 PNT 체계 구축으로 만일의 사태에 발생할 수 있는 상황에 대비할 수 있을 것으로 기대하고 있다. 본 연구에서는 지상기반, 위성기반의 항법시스템에 대한 핵심 기능과 추진계획을 기술하였으며, 관련 연구개발을 통해 더욱 정밀한 서비스 제공으로 해양뿐만 아니라 자율주행 이동체, 무인기 등 여러 산업 분야에 서비스를 확대해 나갈 계획이다.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.1
• /
• pp.5-12
• /
• 2014

In this study, we developed the electric heating equipment and applied for soft ground improvement. The developed heat pipe is 4 m-length and consumes 1 kW/m, which is consisted of Ni-Cr wire. It was installed in 3.5~4.5 m below ground surface and heated for 96 hours (48 hours, 2 times). The temperature variation and vapor pressure caused by electric heating was measured by the thermometer and pressure gauge which were installed in the ground (5.0 m), and the tip resistances were measured by static electronic piezo-cone penetration test (CPT). As the results of experiments, 2-order polynomial curve was shown to adjust the variation of tip resistance and the temperature distribution with the horizontal distance from electric heater, whose R2 value is close to 1. In addition, in-situ pore-water pressure and water content was decreased.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.10
• /
• pp.43-53
• /
• 2012

This study deals with the conventional consolidation methods like preloading and vertical drains. For it, Two different mechanism, i.e., increasing of permeability and evaporating of pore water were studied. The marine clays excavated in Incheon were heated at low temperature($90^{\circ}C$) to increase the permeability. Also, Microwave oven and high-temperature electric heater were used for pore water evaporation. Several points raised from the experiments. To fix them, the electric heating system was revised to upgrade the field application and drain efficiency of pore water, and the marine clays were heated by revised electric heater at high temperature($250^{\circ}C$). From Experimental result showed that results, high-temperature heater induced the pore water evaporation and displayed the excellent consolidation behavior. In addition, the cone index of heated clays were increased about 19 times, which suggested that electric heating system could be applied for ensuring the trafficability of heavy equipments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.33-36
• /
• 1998

BST(66/34) and BSCT(60/30/10) ceramics were prepared by mixed oxide method and studied about the microstructural and dielectric properties with $Y_2$O$_3$, Dy$_2$O$_3$, La$_2$O$_3$, MnCO$_3$. The grain size of undoped BST was 20~30 ${\mu}{\textrm}{m}$, but that of BST, doped content of MnCO$_3$ was 0.1 mol%, was decreased with increasing the contents of $Y_2$O$_3$. As the content of $Y_2$O$_3$ was Increased, Tc was shifted to lower temperature and dielectric constant at Tc was decreased. The dielectric constant of doped BSCT(60/30/10) ceramics ( 0.9 mol% $Y_2$O$_3$. and 0.1 mol% MnCO$_3$) was about 8, 000 at Tc( 22$^{\circ}C$ ).

• Journal of the Korean Ceramic Society
• /
• v.37 no.11
• /
• pp.1044-1050
• /
• 2000

ZnO-Pr$_{6}$O$_{11}$-Co$_3$O$_4$-CaO 사성분계에 SiO$_2$를 0.4at%까지 첨가하여 1180, 1200 및 125$0^{\circ}C$에서 소성하여 미세구조 및 전기적인 특성을 조사하였다. 소성온도 120$0^{\circ}C$ 이상에서 치밀한 시편을 얻을 수 있었고, Si는 주로 입계에 분포하고 있으며, SiO$_2$첨가는 결정립성장을 억제하였다. 이 현상은 고상소결만이 일어나 120$0^{\circ}C$에서 소결된 시편과 액상소결이 일어난 125$0^{\circ}C$에서 소결된 시편 모두에서 관찰되었으며, SiO$_2$첨가에 의한 기공의 증가에 기인하는 것으로 판단된다. SiO$_2$의 첨가에 의해 바리스터의 비선형계수가 크게 변화하였으며, 시편의 소성과정이 고상소결인 경우 비선형계수가 증가한 반면 액상소결인 경우에는 감소하였다. 적절한 양의 SiO$_2$(약 0.3at%)를 첨가하여 액상이 형성되지 않는 120$0^{\circ}C$에서 소성하여 80 이상의 비선형계수를 갖는 바리스터를 제조할 수 있었다.

• Journal of Digital Convergence
• /
• v.20 no.2
• /
• pp.339-344
• /
• 2022

It is about how much fine dust can be efficiently removed with respect to the electric dust collector used in factories and large facilities. The results of evaluating the fine dust removal efficiency are as follows. At 10,000 V, Efficiency method I showed 68.1 %, and Efficiency method II was 58.6 %, which was lower than that of Efficiency method I. At 5,000 V, Efficiency method I showed 57.6%, and Efficiency method II showed 51.6%, which was lower than Efficiency method I. At 2,500 V, Efficiency method I showed 50.3%, and Efficiency method II showed 24.4%, which was lower than Efficiency method I. In case of Efficiency method I, it is the efficiency calculated by using the dust concentration before and after passing through the filter. Efficiency method II calculated Efficiency method II to measure the efficiency a little more accurately in the environment where the air after the filter and the polluted air are mixed. Efficiency method II showed lower efficiency than Efficiency method I. As a result of the electrostatic precipitator test, the dust collecting performance was highest at 10,000 V, followed by 5,000 V and 2,500 V in that order.