• Geophysics and Geophysical Exploration
• /
• v.13 no.4
• /
• pp.357-363
• /
• 2010

In this study, we investigated the geologic structure of the basement and overlying sediments of the construction site of the dinosaur egg fossil museum in Hwasung, Gyeonggi Province through refraction seismology, drilling, and downward seismic velocity measurements in the drill holes. The construction site ($350{\times}750\;m^2$) is located in the reclaimed area south of Sihwa Lake, Gojeong-ri. About 6,950 m of seismic refraction data consisting of 11 lines were acquired using a sledge hammer source. Drilling to the basement was performed at five sites. Sediment samples from drilling were analysed for grain-size distribution and age dating. At two drill holes, seismic velocity was measured with depth using a hammer as a seismic source. The geological structure of the study area consists of, from top to bottom, a tidal flat layer (5 ~ 12 m thick), a weathered soil layer (2 ~ 8 m thick), and the basement. The basement is interpreted as Cretaceous sedimentary rocks that tend to be shallow eastward. The volume of the tidal flat sediments and weathered soil in the study area is estimated as $1.4{\times}10^6\;m^3$, weighing $3.5{\times}10^6$ tons. The rate of sea level rise since 8,000 yrs BP is estimated to be 0.1 ~ 0.15 cm/yr.

• Geophysics and Geophysical Exploration
• /
• v.21 no.4
• /
• pp.255-261
• /
• 2018

The purpose of this study was to obtain a large amount of saline groundwater around coastal aquaculture farms. Thus, we have proposed a method for evaluating the potential amount of saline groundwater resources through the combined analysis of geophysical methods. Refraction seismic survey and electrical resistivity survey were conducted in the vicinity of fish farm at Hadong, Gyeongnam Province. As the result, the velocity of layer in the range of 900 ~ 2,400 m/s was found to be saltwater aquifer with high water content. Geological drilling investigation and analysis of soil samples also showed that the soil at study area was the same as the texture of sandy loam layer in agricultural radial collector wells installed by KRC (Korea Rural Community Corporation). Futhermore, the study area turned out to be quite possible to develop saline groundwater from the coastal shallow aquifer. Therefore, parallel analysis of refraction seismic surveys and electrical resistivity surveys at coastal area are expected to be very useful for the detection of the aquifer composed of sand and gravel layers with high porosity in sandy sedimentary layers along the coastal area.

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.108-113
• /
• 2006

Urban conditions, such as existing underground facilities and ambient noise due to cultural activity, restrict the general application of conventional geophysical techniques. At a tunnelling site in an urban area along an existing railroad, we used the refraction microtremor (REMI) technique (Louie, 2001) as an alternative way to get geotechnical information. The REMI method uses ambient noise recorded by standard refraction equipment and a linear geophone array to derive a shear-wave velocity profile. In the inversion procedure, the Rayleigh wave dispersion curve is picked from a wavefield transformation, and iteratively modelled to get the S-wave velocity structure. The REMI survey was carried out along the line of the planned railway tunnel. At this site vibrations from trains and cars provided strong seismic sources that allowed REMI to be very effective. The objective of the survey was to evaluate the rock mass rating (RMR), using shear-wave velocity information from REMI. First, the relation between uniaxial compressive strength, which is a component of the RMR, and shear-wave velocity from laboratory tests was studied to learn whether shear-wave velocity and RMR are closely related. Then Suspension PS (SPS) logging was performed in selected boreholes along the profile, in order to draw out the quantitative relation between the shear-wave velocity from SPS logging and the RMR determined from inspection of core from the same boreholes. In these tests, shear-wave velocity showed fairly good correlation with RMR. A good relation between shear-wave velocity from REMI and RMR could be obtained, so it is possible to estimate the RMR of the entire profile for use in design of the underground tunnel.

• Korean Journal of Optics and Photonics
• /
• v.8 no.6
• /
• pp.450-455
• /
• 1997

A pulsed Ti:sapphire laser with a Z-folded cavity, which was pumped by a freqeuncy-doubled Nd:YAG laser, was developed. It shows 120 nm wavelength tuning range from 740 nm to 860 nm with 90 nm FWHM under a pumping energy of 3 mJ with 18% output coupler. Using a birefringent filter, the effective efficiency was improved about 10 times compare to without a birefringent filter. The output energy obtained was $\365mu$Jwith 4 nm FWHM. And the wavelength tuning range was broadened to about 160 nm within an output energy fluctuation of $\pm$10%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.297-301
• /
• 2000

Planar optical waveguides which have a higher refractive index than that of substrate were fabricated by proton exchange between $Li^+$ and $H^+$. Benzoic acid was used as proton source and process was carried out under the various reaction time and temperature. The depth of waveguide layer and the generated mode number were investigated by standard prism coupler. The cut-off depth for the fabrication of single mode optical waveguides was obtained by the function which was expressed on refractive index profile. Finally the experimental conditions for cut-of depth of single mode could be confirmed. Channel waveguides were manufactured from these confirmed conditions and the effective confinement of the induced light into waveguides was observed.

• Economic and Environmental Geology
• /
• v.28 no.5
• /
• pp.481-485
• /
• 1995

This paper presents a new approaching method to determine the velocity and geometry of shallow subsurface from seismic refraction events. After picking the first breaks from seismic refraction data, we assume that field refraction seismogram can be replaced by the unit delta function having time shift of first break. Time curves are generated by shooting ray tracing. The partial derivatives seismogram for a damped least squares method is computed analytically at each step of the forward ray tracing. The technique is successfully tested on synthetic and real data. It has the advantage of real full waveform inversion, which is robust at low frequency band even if the initial guess is far from the true model.

• Korean Journal of Optics and Photonics
• /
• v.27 no.6
• /
• pp.229-232
• /
• 2016

Metamaterials operating in the terahertz frequency range show promising potential for use in highly sensitive microbial sensors that are capable of effectively detecting microorganisms in the ambient environment. We were able to detect extremely small numbers of microorganisms by measuring the differential transmission spectra (DTS) of the metamaterial resonances. This was possible because their sizes are on the same scale as the microgaps of the terahertz metamaterials. DTS depend critically on the number of microorganisms placed in the gap area, and their dielectric constant. In addition, these metamaterial microbial sensors are reusable, because the microorganisms can be completely removed by fungicide solution. Finite-difference time-domain simulations successfully reproduce our experimental data.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.6
• /
• pp.574-585
• /
• 2007

To analyze the incident wave characteristics around Haeundae beach the long-term deep water wave data computed by wave hindcast method were used and a continuous wave observation was carried out for 1 year at the 20 m of water depth in front of Haeundae beach. Wave observation data showd that the prevalent wave direction was SSW-S in spring and summer seasons while E-SE in autumn and winter. A numerical modeling shows that the waves from E-SE are refracted strongly due to the shoal developed at the south-east side of Haeundae beach. The simulation also shows inflowing nearshore current along the east coast of the beach develops strongly in autumn and winter. Radioactive isotope tracer experiment for 155 days indicated that the tracers moves to the on-shore direction in the 1st and 2nd tracking then dispersed to the E-W direction along the shore.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.3
• /
• pp.19-32
• /
• 2003

In the conventional photorefractive joint transform correlator(PRJTC), the intensity ration of input signal-to-pump beam should be large enough to saturate two-beam coupling transfer function to obtain a desired correlation result. As a result, the signal-to-noise ratio(SNR) of correlation result is decreased in a noisy input image. In this paper, we propose the improved method for increasing the SNR of the PRJTC by using the characteristics of BaTiO$_3$. We stop the energy transfer saturating by low intensity ratio of input beam and realize a short length of effective interaction in BaTiO$_3$ by making large incident angle of the signal beam. So the gain in high frequency area is decreased and the gain in low frequency area comes up to the saturation gain of the beam coupling transfer function. Therefore the SNR is improved in noisy input image and the PRJTC can be easily realized by low intensity ratio of input beam.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.69-79
• /
• 1999

In this paper, we proposed a diffuion model of Ti diffused lithium niobate optical waveguide for fabricating waveguides with high refractive index and compared with conventional one. The achivement of low optical insertion loss between waveguide interface and single mode fibers was discussed as a function of Ti thickness for $\lambda$=1.55$\mu\textrm{m}$ The proposed diffusion method exhibited higher refractive index waveguide than conventional one for $\lambda$=0.6328$\mu\textrm{m}$ We have achieved the total fiber-waveguide-fiber insertion loss as low as 0.5dB/cm in z-cut and 1$\pm$0.5dB/cm in x-cut for both TM and TE mode of Mach-Zehnder interferometric waveguide in the range of Ti thickness 1000-1400$\AA$ for $\lambda$=1.55$\mu\textrm{m}$ From these results, this diffusion model for making a low loss waveguide can be used for low-power-modulators and switches.