• Journal of the Mineralogical Society of Korea
• /
• v.27 no.4
• /
• pp.183-195
• /
• 2014

In order to study the mineralogical characteristics of a cathodic deposition-metallic powder, electrowinning experiments were carrier out on different electrolytic solutions at varying electric distances and electric currents. Under the same experimental conditions, Cu recovery was obtained much more effectively using a sodium chloride electrolyte than with a sulfuric acid electrolyte. In XRD analysis, copper ($Cu^0$), chalcanthite and cuprite were identified in the sulfuric acid electrolyte, while copper, nantokite and chalcanthite were observed in the sodium chloride electrolyte. In the sodium chloride electrolyte solution, increasing the electric distance and the electric current increased the Cu recovery rate, anode weight and anodic corrosion. The results of XRD analysis with non-pulverized cathodic deposition-metallic powder showed the average copper crystallite size was increased by increasing the electric current and decreasing the electric distance. It is suggested that the mass transfer was controlled with diffusion on the boundary between the electrode and the electrolytic solution due to the formation of dendrite copper.

• Applied Chemistry for Engineering
• /
• v.25 no.2
• /
• pp.157-160
• /
• 2014

We examined and compared the feasibility of vegetable oils with synthetic thermal conductive oils to recover highly purified copper metal from waste jelly-filled communication cables. While polydimethylsiloxane shows relatively poor separation efficiency under entire operating conditions, dibenzyltoluene and waste vegetable oil show the high separation efficiency if the appropriate operating temperature and time were given. By running 50 kg-class equipment with waste vegetable oils, we obtained 100% copper metal recovery with 99.2% purity at $300^{\circ}C$ for 60 min.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.95-100
• /
• 2017

In this study, $Fe_2O_3$ was added as a flux to decrease melting temperature and refine during melting of Cu powder from scraped surface of the waste PCB (printed circuit board). The effect of $Fe_2O_3$ ratio to Cu powder and temperature on the recovery of Cu and content of impurities were investigated. It was found that the recovery of Cu was increased with increasing addition ratio of $Fe_2O_3$ and reaction temperature. The contents of O, Si and Fe in Cu phase were also decreased with increasing addition ratio of $Fe_2O_3$ and temperature. The formation of fayalite ($2FeO{\cdot}SiO_2$) and iron oxides phases in the slag was confirmed by XRD analysis after reaction with $Fe_2O_3$. Therefore, it was considered that the decrease of melting temperature and viscosity of slag by formation of fayalite slag contributed remarkably to the Cu recovery.

• Resources Recycling
• /
• v.21 no.6
• /
• pp.39-44
• /
• 2012

An attempt to recover copper from electroless plating wastewater has been made through evaporation followed by the electrowinning method. From the determination of each element in electroless plating wastewater, the content of Cu was found to be 582 mg/l and small amount of Fe was also contained in it. Moreover, the content of COD and TOC which was resulted from the addition of Rochell salt was found to be 9,560 and 13,100 mg/l, respectively. The content of formic acid generated by the oxidation of formaldehyde was determined to be 7.73 %. As a result, current efficiency was decreased with increase in current density and therefore current density less than $40mA/cm^2$ should be maintained to obtain current efficiency more than 80 %. The content of Fe in Cu obtained by electrowinning was found to be 0.021 and 0.01 % at the concentration of sulfuric acid of 2 and 10 vol%, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.224-225
• /
• 2015

폐솔더 박리액으로부터 주석 및 구리의 분리를 위하여 옥살레이트 침전을 통해 각각 금속염으로 회수하기 위한 기초 연구를 실시하였다. 먼저 옥살산의 첨가량에 따라 주석의 침전율이 증가하였으며 당량비(옥살산/주석)의 1.0-1.5배를 첨가할 경우 주석이 99.5%, 구리는 2.0% 정도 침전되었고 철, 납 등은 거의 침전되지 않아 주석만 선택적으로 침전되는 것을 확인 하였다. 반응온도 증가에 따라 주석의 침전율은 증가하여 $60^{\circ}C$ 부근에서 최대값을 보이다가 온도가 더 증가하면 오히려 감소 경향을 보였다. 침전물의 고액분리 용이를 위해 카티온성 고분자 응집제를 이용하여 침강시킨 후, 분리된 침전물을 건조, 분쇄하여 $SnO_2$의 산화물을 얻을 수 있었다. 주석이 제거된 폐솔더 박리액에 옥살산을 첨가하여 구리가 약 91% 이상 침전되어 납, 철 등의 금속과 분리하여 선택적으로 회수가 가능하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.6015-6022
• /
• 2013

It has been known that there are large amount of nitric acid and valuable metals, copper in the plating waste solution of automobile wheel. As nitric acid and valuable metals are high price and toxic, they should be recovered for economics and environment. Plating waste was extracted with TBP diluted with kerosene. The concentration of nitric acid in aqueous phase was analyzed by titration method by NaOH solution (0.1~1.0N) and the amount of metals by ICP-MS and ICP-AES. The concentration of copper in plating waste were 76,850 mg/L. The concentration of nitric acid in plating waste was 1.02 M. After three step extraction was performed with 50% TBP, each organic phase was stripped three times with distilled water to obtain 48.1% of nitric acid. Purity of final nitric acid was over 99.9% by ICP analysis. After recovery of nitric acid, copper was extracted with various solvent extractors like PC 88A, D2EPHA, LIX 84 and ISE 106. Among these extractors, 92% of copper was recovered by ISE 106 after 1st extraction and 30% $H_2SO_4$ stripping. Copper ion was reduced with $N_2H_4$ to make metal powders, respectively.

• Resources Recycling
• /
• v.23 no.3
• /
• pp.37-43
• /
• 2014

A study has been made on the recovery of tin and copper from waste solder stripper by oxalate precipitation. With the increasing of the oxalic acid addition, tin was precipitated effectively and removed above 99.5% of tin when the oxalic acid, in an amount 1.0-1.5 times the stoichometric requirement, was added. But, in this case, only 2.0% of copper was precipitated and lead, iron were not precipitated. So, tin was selectively removed from the waste solution. With the increasing of the reaction temperature, the removal percentage of tin was increased and maximum value at arounf $60^{\circ}C$ and decreased with increase in the temperature any more. After filtering the precipitate and drying in oven, $SnO_2$ was obtained from the precipitate. After removal of tin in stripping solution, above 91% of copper was selectively removed by Cu-oxalate by addition of oxalic acid.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.217-218
• /
• 2015

주석은 최근 첨단 전기, 전자 제품의 핵심 소재로써 지속적인 수요 증가가 예상되는 전략 금속이다. 국내의 수요량은 2011년 기준 약 17,000톤 으로 99% 이상 수입에 의존하고 있는 실정이다. 그러나, 국내의 주석 제련 산업은 전무한 상태이며 폐자원에서 재활용하는 회수 기술도 초보 단계이다. 이러한 폐자원 발생량은 12,000톤/year이며, 약 1200억원에 달하는 규모이다. 다양한 폐자원의 선별적 전처리 요소 기술 개발 및 회수 공정 시스템 개발이 절실히 요구된다. 본 연구에서는, 주석 폐자원 중 solder 용융물 및 공정 스크랩 Lead solder, Lead-free solder 등 뿐만 아니라, ITO target 제조 시 발생하는 ITO sludge 등의 고상 폐자원으로부터 페자원의 물성을 파악하여 금속/산화물과의 파/분쇄 및 분급공정을 통하여 고품위의 주석 금속을 회수하였다. 뿐만 아니라, 고순도 주석시 발생하는 양극 슬라임 침출액 등의 액상 폐자원으로부터 희소금속의 추출 및 회수를 위해 습식 전처리 공정을 수행하였다. 침출액은 주석, 구리, 납 등의 유가금속이 이온형태로 존재하고 있으며, Chlorine이 다량 함유되어 있다. 고품위의 주석 산화물을 회수하기 위하여 침출액 내의 구리 제거 공정, Chlorine 제거 공정 등을 순차적으로 수행하여 고품위의 산화물 회수를 수행하였다.

• Resources Recycling
• /
• v.17 no.4
• /
• pp.37-46
• /
• 2008

In view of the increasing importance of the waste recycling to meet the strict environmental regulations, the present investigation reports an adsorption process using cationic exchanger DOWEX G-26 for the recovery of copper from the synthetic sulphate solutions containing copper 0.3 to 0.5 mg/ml, similar to the CMP waste effluent of electronic industry. Various process parameters viz. contact time, solution pH, resin dose, and A/R ratio for elution were investigated to recover copper from the effluents. Complete adsorption of copper from the solution was achieved at equilibrium pH 2.5 and aqueous I resin (A/R) ratio of 100 ml/g in 14 minutes contact time. The adsorption of copper on DOWEX G-26 resin was found to follow the Langmuir isotherm and second order reaction. The copper was eluted from loaded resin with dilute sulphuric acid to produce copper-enriched solution.

• Resources Recycling
• /
• v.24 no.3
• /
• pp.3-10
• /
• 2015

A study has been made on the recovery & separation of cobalt and copper from organic acid leaching solution by solvent extraction. The experimental parameters such as the equilibrium pH, concentration of extractant and phase ratio were observed. Copper was extracted using LIX 84 and Cobalt was extracted using cyanex 272 and versatic acid 10. Experimental results showed that extraction percent of copper was 99% at above eq. pH 2.0 and then more than 90% of cobalt were extracted by cyanex 272 in eq. pH 6.0 and versatic acid 10 in eq. pH 7.5. Stripping of copper and cobalt from the loaded organic phases can be accomplished by sulfuric acid as a stripping reagent and 120 ~ 150 g/L of $H_2SO_4$ was effective for the stripping of copper and cobalt respectively. Finially, the basic optimal process for recovery of copper and cobalt from the bio-leaching solution was proposed.