• 한국전산유체공학회:학술대회논문집
• /
• 2000.10a
• /
• pp.115-122
• /
• 2000

본 연구에서는 2 차원 벽구동 캐비티 유동에 의하여 나타나는 이력효과에 의한 분기(Bifurcation)현상을 전산유체기법을 사용하여 연구하였다. 캐비티는 북쪽과 동쪽벽이 움직일 수 있고, 다른 두 벽은 고정되어있는 구조이다. 실험은 Reynolds 수 100 에서 1000까지 증가시켜가면서 북쪽벽과 동쪽벽을 동시에 가속 시켜 정상상태에 이르게 한 경우와 북쪽벽이 먼저 가속되어 정상해에 이른 후 동쪽벽을 나중에 가속하여 재차 정상상태에 이르게 한 경우를 비교하였다. 그 결과 Reynolds수가 약 200이상부터 벽에 작용하는 항력, 유량함수의 값, 재부착점등이 분기현상을 나타냄을 확인하였다.

• Solar Energy
• /
• v.18 no.2
• /
• pp.115-121
• /
• 1998

In this study a channel cavity flow was performed. The channel has small size in the upper cavity region. At the gap is supplied by driven flow for Reynolds number. The experimental study was carried out in a channel cavity with square heat surface by visualization equipment with Mach-Zehnder interferometer and laser apparatus. Heat source was uniform heat flux($0.4W/cm^2,\;0.8W/cm^2,\;1.2W/cm^2$). When the bottom wall is heated, the tendency of natural convection flows are vigorous increasing heat flux.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1537_1538
• /
• 2009

기존의 초소형 렌즈모듈들은 초점 거리 가변을 위한 구동장치가 필요하여 소형화 한계, 큰 전력소모, 부품의 기계적 결함 등 해결해야 할 부가적인 문제점들이 존재하였다. 액체렌즈는 이러한 문제를 해결할 수 있는 유력한 기술로 주목받고 있으며, 특히 부가적인 구동 장치가 필요없고 비교적 간단한 원리로 렌즈 곡률을 조절할 수 있는 일렉트로웨팅 기반의 액체렌즈는 초점 거리 조절 및 줌 조절이 필요한 휴대폰, 캡슐 내시경 등에 적용이 가능하다. 그러나 기존의 일렉트로웨팅 기반의 액체렌즈는 렌즈 캐비티의 크기에서 큰 단점이 있으며, 렌즈모듈구성 시에도 소형화하는데 한계가 존재하였다. 본 연구에서는 렌즈 캐비티를 MEMS 기술을 이용하여 실리콘 기판 상에 제작함으로써 구동회로의 집적이 가능한 액체렌즈를 제작하였다.

• Journal of Ocean Engineering and Technology
• /
• v.12 no.1
• /
• pp.113-119
• /
• 1998

An experimental study was carried out in a three-dimensional cubic cavity driven by 2-dimensional plane Poiseuille flow for three kinds of Reynolds number, $10^4$, 3 $\times$ $10^4$ and 5 $\times$ $10^4$ based on the cavity width and cavity inlet mean flow velcoity. Instant simultaneous velocity vectors at whole field were measured by 2-D PIV system. Laser based illumination and two-frame grey-level cross correlation algorithm are adopted. Severe unsteady flow fluctuation within the cavity are remarkable at above Re = 3 $\times$ $10^4$ Reynolds numbers and sheared mixing layer phenomena are also found at the region where inlet driving Poiseuille flow is collided with the clock-wise rotating main primary vortex at upper center area. Instant velocity profiles reveal that deformed forced vortex formation is observed throughout the separate two areas.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.935-941
• /
• 1998

Experiments were carried out for a cubic cavity flow. Contrinuous shear stress is supplied by driven flow for high Reynolds number and three kinds of aspect ratios. Velocity vectors are obtained by PIV and they are used as velocity components for Poisson equation for pressure, Related boundary conditions and no-slip condition at solid wall and the linear velocity extrapolation on the upper side of cavity are well examined for the present study. For calculation of pressure resolution of grid is basically $40{\times}40$ and 2-dimensional uniform mesh using MSC staggered grid is adopted. The flow field within the cavity maintains a forced-vortex formation and almost of the shear stress from the driving inflow is transformed into rotating flow energy and the size of the distorted forced-vortex increases with increment of Reynolds number

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.2
• /
• pp.176-183
• /
• 1999

This paper is aimed to investigate behaviour of vortex in 2-D step cavity with high Reynolds numbers$(3.2{\times}10^{3},\;10^{4},\;3{\times}10^{4},\;5{\times}10^{4}\;and\;7{\times}10^{4})$. The SOLA algorithm which is MAC type was adopted to solution method computing the flow field on irregular grid. In case of $Re=7{\times}10^{4}$ flow behavior is steady bu periodic unsteady sinusoidal fluctuation of local velocity and kinetic energy is found for $Re=10^{4}$ Continuous movements of small eddies in the secondary flow regions are discov-ered for $3{\times}10^{4}$ Generation of eddies and their active migrating behavior are detected over $Re=5{\times}10^{4}$ resulting in complete unsteady and non-linear flow characteristics Furthermore a typhoon-like vortex(TLV) appears intermittently and rotates along the separation regions and boundary layers.

• Solar Energy
• /
• v.17 no.3
• /
• pp.59-66
• /
• 1997

The present study adopted the PTV method for the velocity acquisition. The system consists of an image grabber built-in a personal computer and a laser-based sheet light projector and particle identification softwares. Velocity vectors are obtained, by PTV and they are used as velocity components for Poisson equation for pressure. Related boundary conditions and no-slip condition at solid wall and the linear velocity extrapolation on the upper side of cavity are well examined for the present study. For calculation of pressure, resolution of grid is basically $40{\times}40$ and 2-dimensional uniform mesh using MAC staggered grid is adopted. The result of experiment reveal that, newly suggested measuring method is capable of estimating pressure and velocity distribution of flow field reasonably.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.4
• /
• pp.430-436
• /
• 1997

Time-dependent Flow characteristics of a two-dimensional lid-driven square cavity flow of six high Reynolds numbers, $10^4 2{\times}lO^4., 3{\times}l0^4, 5{\times}lO^4, 7.5{\times}lO^4$ and $10^5$ were investigated. A convection conservative difference scheme based upon SOLA to maintain the nearly 2nd-order spatial accuracy was adopted on irregular grid formation. Irregular grid number is $80{\times}80$ and its minimum size is about 1/400 of the cavity height(H) and its maximum is about 1/53 H. The result shows that at Re= $10^4$, periodic migration of small eddies appearing in corner separation region and its temporal sinusoidal fluctuation are represented. And another critical Reynolds number which shows the commencement of flow randomness emerging from the periodic fluctuation is assumed to be around Re= $1.5{\times}10$. At five higher Reynolds numbers ($2{\times}lO^4., 3{\times}l0^4, 5{\times}lO^4, 7.5{\times}lO^4$ and $10^5$), an organizing structure of four consecutive vortices similar to a Moffat vortex at two lower corners is revealed from time-mean flow patterns.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.731-736
• /
• 2011

A pneumatic driving solenoid valve operates pneumatic control devices by opening/closing operating flow passage when the command is given by control system for the liquid-propellant feeding system of space launch vehicle. The simulation model of pneumatic driving solenoid valve is designed with AMESim to verify the designs and evaluate the dynamic characteristics and pneumatic behaviors of valve. To validate a valve simulation model, the simulation results of their operating durations of valve by AMESim analysis are compared with the results of experiments. In addition, the results of internal flow simulation with FLUENT are utilized to improve the accuracy of valve-modeling. Using the model, we analyze performance of valve; opening/closing pressure, operating time on various design factors; shape of control valve seat, drainage seat, rate of sealing diameter, volume of control cavity. This study will serve as one of reference guides to enhance the developmental efficiency of ventilation-relief valves with the various operating conditions, which shall be used in Korea Space Launch Vehicle-II.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.144-150
• /
• 2000

In this paper, the formation of a corner cavity in the final stage of axisymmetric backward extrusion process is studied by means of upper bound analysis using kinematically admissible velocity. The quantitative relationships between corner cavity formation and process parameters are studied. And analytical results are compared with those of experiment to which plasticine is used. It is found that the analytical results agree well with experimental one. In addition, to restrict the formation of a corner cavity, driven container is applied to backward extrusion and the results are compared with those of FEM. The critical thickness of the bottom of the billet decreases with increase in reduction of area, and increases with decrease in friction. To prevent the formation of corner cavity, the concept of moving container was applied. Throughout this process, the occurrence of a corner cavity is delayed and forming limit area is enlarged.