• Journal of the Korea institute for structural maintenance and inspection
• /
• v.2 no.4
• /
• pp.224-232
• /
• 1998

구조물에 손상이 발생하게 되면 동적특성이 변하게 된다. 그러므로 이와 같은 특성을 계측하여 구조물의 손상된 정도를 평가하게 되면 이를 상시감시에 활용할 수가 있다. 대표적인 손상기술들을 제작된 모형교량에 서로 다른 경계조건을 구현하여 손상도를 Simulation을 이용하여 결정하고 가장 적법한 방법과 대책을 연구했다. 모형교량은 I-DEAS의 Normal Mode Dynamic Solver를 이용하여 분석 제작되어 계측과 비교평가 되어 손상기술에 적용되었다. 24개의 가속도 감지기를 이용하여 데이터를 획득하였고, Residue법으로 모달인자를 추출하였다. 추출된 동적인자가 상시감시에 적용하도록 구조물의 손상검출기술을 제안한다

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.1
• /
• pp.103-111
• /
• 1999

구조물에 손상이 발생하게 되면 동적특성이 변하게 된다. 그러므로 이와 갈은 특성을 계측하여 구조물의 손상된 정도를 평가하게 되면 이를 상시감시에 활용할 수가 있다. 대표적인 손상기술들을 제작된 모형교량에 서로 다른 경계조건을 구현하여 손상도를 Simulation을 이용하여 결정하고 가장 적법한 방법과 대책을 연구했다. 모형교량은 I-DEAS의 Normal Mode Dynamic Solver를 이용하여 분석 제작되어 계측과 비교평가 되어 손상기술에 적용되었다. 24개의 가속도 감지기를 이용하여 데이터를 획득하였고, Residue법으로 모달인자를 추출하였다. 추출된 동적인자가 상시감시에 적용하도록 구조물의 손상검출기술을 제안한다

• Journal of Korean Society of Steel Construction
• /
• v.16 no.3 s.70
• /
• pp.355-363
• /
• 2004

In order to obtain the effective length factor of beam-column members of plane frames, this paper extensively used an alignment chart approach, based on the nomograph given in LRFD-AISC specification commentaries. However, it should be noted that various simplifications and assumptions were introduced in constructing the alignment chart. To overcome the practical limitations of the alignment chart, this paper proposes a simple but accurate procedure that determined the effective buckling length for stability design of main members of cable-supported bridges. This method requires the full system buckling analysis. The numerical examples showing the suitability of the present scheme are discussed and some conclusions are drawn.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.493-503
• /
• 2009

Bridge redundancy is defined as the capability of a bridge to sustain loads after one of its main members incurs damage. It is affected by many parameters, including the number of girders, span length, girder height, internal supports, and secondary members. The present AASHTO and Korean Bridge design codes, however, define bridge redundancy only as the number of girders, and neither the evaluation method nor the required level of redundancy is given. This study presented a redundancy evaluation method for plate girder bridges with severe fatigue damage based on the reliability method,by considering the essential parameters. A required level of redundancy was also proposed as a target system reliability index from the load capacity analysis and reliability analysis of the basis bridge designed by LRFD. Finally, the level of redundancy of simple and continuous plate girder bridges with a variable number of girders designed by ASD was evaluated and presented.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.75-75
• /
• 2011

본 논문에서는 진동중인 교량 거더에 작용하는 풍하중을 산정하고 그에 따른 플러터 발생풍속을 예측하기 위하여 분산형 전산환경을 활용한 수치해석 연구를 수행하였다. 분산형 전산환경은 웹 포탈을 기반으로 수치해석 환경을 제공하는 수치풍동 시스템으로서, 전산유체역학(CFD : Computational Fluid Dynamics)에 대한 전문지식이 부족한 사용자들도 격자생성, 수치해석자를 이용한 계산, 가시화 등의 전 과정을 편리하게 수행할 수 있는 차세대 토목분야 연구 환경이다. 본 시스템은 그리드스피어(GfidSphere)를 기반으로 구성되었으며, 기본적으로 사용자 관리, 세션 관리, 그룹 관리, 레이아웃 관리 등을 제공하여 사용자가 포탈을 통해서 다양한 서비스를 쉽게 사용할 수 있는 환경을 구축하도록 도와준다. 수치해석을 위한 유체 지배방정식은 2차원 비정상 비압축성 RANS(Reynolds-Averaged Navier-Stokes) 방정식이며, pseudo compressibility 방법을 적용하였다. 비정상 유동장을 해석하기 위하여 이중시간 전진법(dual time stepping)을 사용하였으며, 수렴가속화를 위해 Multi-grid 기법을 적용하였다. 또한 난류 유동장 해석을 위해서 $k-{\omega}$ SST 난류 모델을 사용하였으며, 난류 천이 과정에서의 유동을 모사하기 위하여 Total stress limitation 방법을 적용하였다. 교량 거더의 연직과 회전방향의 2자유도 움직임을 모사하기 위하여 동적격자 기법을 도입하였다. 교량 거더 주변의 비정상 유동해석 결과를 통해, 거더 표면에서 떨어져나가는 크고 작은 와류의 영향으로 양력 및 모멘트 계수 그래프가 중첩된 진폭과 주기를 갖고 주기적으로 나타나는 것을 확인할 수 있었다. 또한 계산된 비정상 공기력을 적용한 2자유도 플러터 방정식을 통하여 플러터 발생풍속을 산정하였다. 최종적으로 본 연구에서 계산된 결과의 타당성을 검증하기 위하여 수치적으로 구한 플러터 발생풍속과 기존의 실험 및 수치해석 결과를 비교하였으며, 결과는 잘 일치하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.77-87
• /
• 2013

A present LSD (limited state design) code for temperature load in the domestic bridge design has applied a uniform standard for various bridge types. In this study, in order to calculate the effective temperature, a specimen of steel box girder bridge section with real size dimension was manufactured. For a year, the temperature data were measured at the 18 point in steel deck of steel box girder bridges specimen. Effective temperature within the cross section according to atmospheric temperature was calculated by this experiment data. The analyzed results were very similar correlation when compared with the effective temperature of the Euro Code. Therefore, the effective temperature which calculated based on the present data could be used as the basic data in order to present to the appropriate design criteria for the thermal loads on the domestic bridge design.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.6
• /
• pp.45-53
• /
• 2010

The unseating failure of bridges, which is one of the most severe types of damage leading to the loss of transportation function, should be avoided in earthquakes. As a measure of prevention of unseating failure resulting from the failure of bearings, bearing-protection devices are frequently used. They are installed beside the bearings and protect the bearings by resisting a seismic load transmitted from the superstructure. In order to show appropriate seismic performance, the strength of anchors as well as of device bodies should be confirmed. In Korea, they have been installed only according to the design provided by device agents, because a proper design method for the anchors has not been established. In this study the performance of bearing-protection devices with various heights of concrete bed blocks has been investigated experimentally, and a proper design method has been proposed to secure seismic performance.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.6 no.2 s.21
• /
• pp.37-44
• /
• 2006

Any vehicle and equipment whose total weight is more than 40ton and its axle weight is 10ton or above is banned to cross any bridge in our country under section 54 in the Highway law. This restriction results from the accumulation and application of safety factors about which there is type specification in the "standard design vehicle". And in "standard design vehicle", Vehicle load to bridge is assumed concentrating one. Based on this restriction, there is an issue that military tank which has a total weight of 51ton (63ton in case of the US tank) can not cross any bridge. However, many research and practical examples concerned manifest that it is possible for military tanks to cross these bridges. The reasons of this issue in the current Highway law's provisions are analyzed in this paper. Correspondingly, feasibility of military tanks passing these bridges are discussed here. At last, considering economical efficiency and practicability for military, several suggestions and improving measures are put forward. This research has certain reality significance to guide bridge design considering the passage of military heavy vehicles.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.3
• /
• pp.83-90
• /
• 2010

Composite materials can be used economically and efficiently in civil engineering applications when standards and procedure for analysis, design, construction and quality control are to be established. Bridge systems, including the girders and cross-beams, and concrete decks behave as the specially orthotropic plates. For such systems with sections, boundary conditions other than Navier solution types, it is very difficult to obtain its analytical solution. To design the bridge made by the composite materials, cross-section was used as the form-core shape for economical reason and finite difference method was used for output of the stress value. The Tsai-Wu failure criterion for stress space is used. In this paper, the rate of tensile strength reduction due to increased size was considered. And also numerical study is made for these cases.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.47-58
• /
• 2007

The usage of Integral abutment bridges has been increased worldwide because of reducing bridge maintenance costs and resisting seismic loads. Although these attributes make the integral abutment bridge an increasingly popular choice, back-abutment interaction issues remain unresolved. Hence, the earth pressure behavior of an integral abutment bridge having 90 m long PSC beam bridge for the first time in Korea was analyzed by conducting long term monitoring in this study. Based on this study, the results were as follows; the ratio of maximum passive movement to the abutment height (H) of 0.0027 and the maximum passive earth pressure coefficient of 4.8 were developed at 0.82H from the bottom of the abutment during summer season. During winter season, the ratio of maximum active movement to H of 0.0011 and the maximum active earth pressure coefficient of 0.7 were developed at the same location as in summer season. The new earth pressure distributions having a trapezoid type were proposed based on this study.