• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.221-221
• /
• 2018

국내에 대부분 교량은 빗물이 원활하게 배수되도록 사전에 강우에 대비하여 배수시설을 설계하도록 되어있다. 다수의 교량에서는 점배수와 선배수의 방식을 사용하여 설계 되고 있으나 외부로 노출되어야하는 구조적 문제로 인해 설계시에는 검토되지 않으나 도시미관을 저해하는 요소가 된다. 본 연구에서는 도시미관개선을 위해 교량의 배수시설을 내제한 프리캐스트 교량 방호벽의 개발과 내부에 내제된 배수관의 배수성능을 3차원 모형인 Fluent 모형을 통해 수치해석을 수행하였으며, 교량 측구에서의 흐름 및 횡배수관의 유입에 관해 3차원 흐름을 확인하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.19-26
• /
• 2014

Concrete guide rail and median barrier are an attached RC member, however they are vulnerable to cracking due to slip form construction and large surface of member. In this study, causes and pattern of cracking are analyzed through assessment and NDT (Non-Destructive Technique) evaluation for concrete guide rail and median barrier on highway structure. For this work, analysis on drying shrinkage and hydration heat are performed considering installation period, and plastic shrinkage is also analyzed considering their environmental conditions. From the evaluation, plastic settlement around steel location, drying/ plastic shrinkage, and aggregate segregation are inferred to be the main causes of cracking in the structures. The crack causes and patterns are schematized and techniques of crack-control are suggested. Furthermore concrete guide rail/ median barrier in the bridge on the sea are vulnerable to cracking at early age so that special attentions should be paid at the stages of material selection and construction.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.1
• /
• pp.91-101
• /
• 2008

Structural analysis models to develop live load distribution factors of simply supported prestressed concrete I-girder bridge should have the precision of the analysis results as well as modeling simplicity. This is due to the numerous frequency of structural analysis needed while developing live load distribution factors. In this study, an appropriate structural analysis model is selected by comparing previous researchs studies and models used in practical design. Also, the influence by the flexural stiffness of barrier and diaphragm on the live load distribution had been analyzed through comparing the numerical analysis and experimental tests. As a result, the model that the eccentric girder and the barrier and diaphragm are connected to the deck plate was appropriate in satisfying both accuracy and simplicity for structural analysis of simply supported prestressed concrete I-girder bridge. However, the barrier was analyzed to have insignificant influence on the live load distribution in spite of its variation of stiffness. The eccentric diaphragm showed little influence at 25% or higher of flexural stiffness. From the results, a model that the girder is rigidly connected to the deck plate in consideration of the eccentricity, the barrier is ignored and the whole section of diaphragm is supposed to be valid without eccentricity is decided as the most appropriate structural model to develop the live load distribution factors of simply supported prestressed concrete I-girder bridge in this study.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.325-335
• /
• 2006

In this paper, flexural test, girder-connection test and barrier-connection test for the pultruded composite bridge deck of hollow section, were carried out and its structural characteristics were evaluated. In the flexural test specimen, deflection was measured at center of the span and strains were measured at various locations to see the structural behavior up to the failure. In addition, finite element analysis was performed for the flexural test specimen and the results were compared with experiments, and load carrying capacity was evaluated. Also, field load test was conducted for the demonstration plate girder bridge and other field applications were described.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.6
• /
• pp.17-25
• /
• 2010

This paper studied on stability of the U-channel segmental concrete bridge under vehicle-impact loads. The U-channel bridge has advantages in that it reduces an additional dead load and the edge beams role as a barrier. But it has a dangerous factor which collapses the bridge structure when the edge beams are ruptured. Therefore, it is necessary to verify behaviors of the bridge system under vehicle-impact loads. Static and dynamic vehicle impact simulations were carried out on the basis of AASHTO LRFD design specifications. In case of the static analysis, equivalent static loads specified in the AASHTO codes are loaded on the edge beams and in case of the dynamic analysis, FEM vehicle models are modeled by applying the dynamic test specifications of AASHTO codes. As a result, it is shown that U-channel bridge system has sufficient safety against static and dynamic impact loads specified in the AASHTO LRFD design specifications.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.604-613
• /
• 2018

In recent years, numerous train derailment accidents caused by deterioration and high speed technology of railways have increased. Guardrails or barriers of railway bridges are installed to restrain and prevent the derailment of the train body level. On the other hand, it can result in a high casualties and secondary damage. Therefore, a Derailment Containment Provision (DCP) within the track at the wheel/bogie level was developed. DCP is designed for rapid installation because it reduces the impact load on the barrier and inertia force on the steep curve to minimize turnover, fall, and trespass on the other side track of the bridge. In this paper, DCP was analyzed using LS-Dyna with a parameter study as the impact loading location and interface contact condition. The contact conditions were analyzed using the Tiebreak contact simulating breakage of material properties and Perfect bond contact assuming fully attached. As a result, the Tiebreak contact behaved similarly with the actual behavior. In addition, the maximum displacement and flexural failure was generated on the interface and DCP center, respectively. The impact analysis was carried out in advance to confirm the DCP design due to the difficulties of performing the actual impact test, and it could change the DCP anchor design as the analysis results.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.251-251
• /
• 2018

도로설계기준(2012)에 따르면 노면 배수시설은 측구, 집수정, 배수관, 배수구(빗물받이, 맨홀) 등으로 구성되며 중앙분리대 배수에서 구조가 방호벽일 경우 원칙적으로 집수정과 종배수관, 횡배수관을 설치하여 노면수를 배수한다. 최근 기후변화에 따른 국지성 집중호우로 교량 배수시설의 배수능력 부족으로 교량의 노후화, 노면의 체수와 수막현상을 야기한다. 교량 설계 시, 교량의 외관은 점배수에 의한 배수불량으로 막힘부에서의 식물생육, 부식, 배수구의 오염 등으로 심미성에 악영향을 미치고 있다. 따라서 국토교통부 도로 배수시설 설계 및 관리지침에서는 기존의 집수정으로 유도하여 배수하는 점배수 형태에서 우수의 지체시간을 저감하기 위해 배수구로 즉시 배수되어 배수 효율을 증가시켜주는 선배수시설을 권장하고 있다. 그러나 선배수 구조의 일반적인 내용만을 기술하고 있으므로 보다 상세한 설계기준이 필요하다. 또한 국내에서는 교면 배수를 위한 횡배수구의 배수능력에 관한 설계 개념은 미국의 빗물받이 설계 개념을 그대로 적용하고 있어서 교량 배수시설의 배수능력 증대를 위한 수치 및 수리실험에 관한 기술적인 자료가 부족한 실정이다. 따라서 도로의 흐름해석 및 선배수를 위한 측구 횡배수관의 흐름개선에 관한 구체적인 연구가 필요한 실정이다. 본 연구에서는 배수로 전반의 유향 분석 및 횡유입관 유입부에서의 상세한 흐름해석과 통수능력을 분석하기 위해서는 수리실험을 통한 연구가 필요한 실정이다. 그러나 최적 횡배수관의 형상 및 간격 설정에 대한 수리실험의 물리적 및 시간적 한계를 극복하기 위해 Fluent 모형(Ansys Workbench 13.0)을 활용한 수치모의를 수행하여 모형의 적용성을 검토하였다. 다상유동 해석을 위해 VOF(Volume of Fluid)방법을 적용하였고, 수치해석 방법으로는 비정상류, 난류 모형으로는 standard ${\kappa}-{\varepsilon}$모형을 적용했다. 도로 형상에 따른 우수유출량을 비교 분석하기 위하여 횡경사는 2%로 고정하고 종경사를 2%로 선정하여 수치모의를 통한 배수능력을 분석하고 설계에 직접적인 적용성을 검토하였다. 횡배수관의 간격변화 및 배수공의 위치 변화 등에 따른 차집량을 분석하였으며, 개략적인 수리실험 결과와 수치모의의 차집율을 비교 및 분석하여 Fluent 모형의 적용성을 확인하였다. 또한, 횡배수관의 유입부에서의 유속 변화 및 유출부에서의 유속이 모의가 가능하므로 배수시설에서 보다 정확한 흐름 해석이 가능하여 보다 적정한 배수능력 분석이 가능할 것으로 판단된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.35-43
• /
• 2006

In this paper, procedures and research results involved in the development of glass reinforced composite bridge deck of hollow section were presented. Laminate design for the 3 cell deck section was performed. Structural characteristics such as serviceability, strength, failure and stability for DB24 load were analytically studied through the finite element analysis for the composite deck plate girder bridge. Composite deck tube was fabricated with pultrusion and extensive tests such as flexural test, girder-connection test, barrier-connection test, compression fatigue test and flexural fatigue test were carried out to evaluate structural behavior experimentally. Also, field load test was conducted for the demonstration plate girder bridge with composite deck and requirements for the strength and serviceability were reviewed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.451-457
• /
• 2014

Recently, as a means of resolving the issue of legal liability in the event of an accident or a disaster, a wide variety of simulation techniques, such as structural and structure-fluid interaction analysis, have been used in the field of forensic engineering. The plate girder bridge discussed in this paper was being constructed between a pier and an abutment to expand an existing bridge, but an accident whereby the bridge overturned occurred at the end of the concrete laying process for a protective wall. This accident was caused by additional loads not being considered at the time of the design as well as the actual construction being different from the design. The additional loads ultimately generated a negative support force. In this study, we determined the cause of the accident by comparing the structural stability of the original design with that of the additional, non-conforming construction using MIDAS structural analysis.

• Korean Journal of Environment and Ecology
• /
• v.25 no.5
• /
• pp.649-657
• /
• 2011

This study had targeted the Manjong Junction~Hongchun interchange section of Jungang highway in order to analyze the efficiency and improvement of the highway wild-life fences. Being analyzed wild-life fence as an effective facility for the prevention of road-kill, it had founded that the wild animals did not jump over even the two layer guardrail, concrete barrier and noise barrier, fence for rock fall. For the section with high road-kill decrease effect after installing the wild-life fence, the effect was higher at wild-life fence with the height of 1.0m where the door had not been installed and the well connected points of road facility than the area with fence height of 1.5m. The road-kill decrease effect was also high at the well managed areas even if the door has not been installed. Also, road-kill had occurred by concentrating around the end of wild-life fence after installing the fence, Moreover road-kill had also occurred around the cutting section. The door of wild-life fence had higher amount of road-kill occurrence as the installation interval was closer. it was analyzed that the door management has a lot of effect on road-kill decrease. The fence for rock fall, two layer guardrail and concrete barrier having the effect of wild-life fence installed on the road would have to be installed by connecting with wild-life fences through proper facility improvement. Although the door should not be installed if possible, it should be installed as automatic door or gravity door to prevent the door from leaving the door open. An escape route has to be formed for the prompt escape away from the road for the animals entered through the ending section of the fence. The eco-corridor has to be made by restoring the soil layer of dual purpose eco-corridor forming a planting area. Also, the dead body after the accident has to be disposed to the outer section of the road immediately in order to prevent the secondary road-kill by the predator from the road-kill. The fence has to be installed as 500m or longer in both ways, in other words 1,000m or longer, from the targeted spot of minimum accident prevention while connecting up to the bridge or box culvert, etc that are next road facilities if possible to guide wild animals safely to the eco-corridor.