• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.564-567
• /
• 2012

Optical fibers are going to be used for telecommunication, image fibers, sensors under irradiation in nuclear power plants and various irradiation facilities. Especially, Temperature detection sensors using Raman light scattering, temperature or strain sensors using fiber gratings, magnet-optical sensors using photo-magnetic effect, are already commercialized. However, When fibers are exposed to ionizing radiation, color centers are formed in fibers which reduces their light transmission, and it is limited in applying under radiation environments. In this study, $Co^{60}$ gamma-ray induced optical attenuation on Ge-doped single mode(SM) fiber has been measured. Gamma-ray is irradiated for 4hours at the dose rate of 0.5kGy/hr, 2kGy/hr, 8kGy/hr. Consequently, gamma-ray induced loss based on radiation effects in Ge-doped SM fiber occur precisely. Furthermore, dose rate effect that the higher dose rate in the same total dose, the more increase loss of optical fiber and annealing effect that the higher the loss after irradiation, the more increase the recovery rate of the loss are observed in the fiber. This results plan to make use of bases in the study of the radiation-hardened optical fiber.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.45-49
• /
• 1999

The second harmonic, wavelength is 397nm, of the continuous wave diode laser, whose maximum power is 35mW, was generated in $LiIO_3$ crystals in a ring enhancement cavity. 5mm- and 10mm-long crystals cut $43.21^{\circ}$ for optic axis were used in this experiment. Both surfaces of those were anti-reflection coated for 794nm. In case the crystal was inserted into the cavity, the condition of separation between two concave mirrors for the optimum mode matching was found. The conversion efficiency of second harmonic generation was increased by the resonant enhancement of pumping power in the ring enhancement cavity, and the frequency of diode laser was locked to that of the counter-propagation mode generated from the surface of crystal. When the pumping power was 28 mW, the infrared buildup factor was about 45 without the crystal, and 14 with the crystal due to the transmission loss of crystal. The maximum second harmonic powers of $1.5{\mu}W$ and $6.6{\mu}W$ were obtained, and corresponding conversion efficiencies were $(6.584{\pm}0.56){\times}10^{-3}$%, $2.6{\pm}0.21){\times}10%{-2}$% in 5mm- and 10mm-long $LiIO_3$, respectively.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.291-298
• /
• 2020

ZITO/Ag/ZITO multilayer transparent electrodes at room temperature on glass substrates were prepared using RF/DC magnetron sputtering. Transparent conductive films with a sheet resistance of 9.4 Ω/㎡ and a transmittance of 83.2% at 550 nm were obtained for the multilayer structure comprising ZITO/Ag/ZITO (100/8/42 nm). The sheet resistance and transmittance of ZITO/Ag/ZITO multilayer films meant that they would be highly applicable for use in polymer-dispersed liquid crystal (PDLC)-based smart windows due to the ability to effectively block infrared rays (heat rays) and thereby act as an energy-saving smart glass. Effects of the thickness of the PDLC layer and the intensity of ultraviolet light (UV) on electro-optical properties, photopolymerization kinetics, and morphologies of difunctional urethane acrylate-based PDLC systems were investigated using new transparent conducting electrodes. A PDLC cell photo-cured using UV at an intensity of 2.0 mW/c㎡ with a 15 ㎛-thick PDLC layer showed outstanding off-state opacity, good on-state transmittance, and favorable driving voltage. Also, the PDLC-based smart window optimized in this study formed liquid crystal droplets with a favorable microstructure, having an average size range of 2~5 ㎛ for scattering light efficiently, which could contribute to its superior final performance.

• Progress in Medical Physics
• /
• v.16 no.2
• /
• pp.104-109
• /
• 2005

Photodynamic therapy (PDT) is one of the expectable current cure operation methods. Tumor tissue is treated by abundant oxygen in a body and generated singlet or free radical from exterior laser diode and photosensitizer. Current problem of PDT is the low penetration power of the light beam in a deep seated large tumor and solid tumor thus results in low treatment outcome. In the study, we tried to develop interstitial photodynamics therapy treatment to solve this problem. As the accurate determination of light dosimetry in biological tissue is one of the most important factors affecting the effectiveness of PDT, parameters used in this study are the optical property of biological tissue. Since biological tissues have large scattering coefficient to visible light the penetration depth of a biological tissue in visible light region is only $15\~20$ mm. We showed that it is possible to measure fluence rate and penetration depth within the biological tissues by Monte Carlo simulation very well. Based on the MC simulation study, the effectiveness of interstitial photodynamic therapy on tumor control in solid tumor was proved through in vivo animal experiment.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.4
• /
• pp.339-349
• /
• 2007

For various types of the Pungchon limestone, diverse mineral characters of the limestone including their size and morphology are investigated by using of ELS and SEM to examine the possibility of application as fillers to paper industry. Also, the measurement of zeta potential and the evaluation of coagulation properties in calcite suspension was made for fine powders of the limestone to examine the applicability and efficiency in wet-papermaking process. Fine powder of the Pungchon lime-stone, largely controlled by original mineral characters of ore in mineralogical aspects, exhibits some-what different trend in particle morphology according to ore types, and thereby, the size distribution, zeta potential and coagulation properties also become different. The examined whiteness, brightness, opacity and sheet strength in hand sheet also show remarkable differences according to ore types. These are seemed to be basically due to the results of combined effects of whiteness, site distribution, refractive index, and morphology of the limestone powder on the properties of hand sheet. Considering the investigated results, all types of the Pungchon limestone appear to be sufficiently applicable to paper industry. Especially, the mega-crystalline calcite type is evaluated to be overall suitable for the purpose of paper industry due to the higher values in whiteness and brightness. In addition the fine powder of micro-crystalline calcite type is assessed particularly to have a good quality in sheet strength by virtue of irregular particle shape.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.370-381
• /
• 2015

In the system of poly(vinyl alcohol) (PVA)/dimethyl sulfoxide, the refractive index of polymer was very well matched to that of solvent and thus its scattered intensity could be minimized. After adding small amount of polystyrene latex particle (nominal diameter 200 nm), diffusion behavior of only probe particle was investigated against the concentration of polymer matrix by means of dynamic light scattering. The polymer concentration dependence of its reduced diffusion coefficient was able to be analysed with the stretched exponential function of the reduced concentration $C[{\eta}]$. In very dilute concentration regime, the depletion layer kept constant but at the early semi-dilute regime of $1{\leq}C[{\eta}]{\leq}2.5$, the concentration-dependent exponent of depletion layer ${\delta}$ was appeared to be -0.8 which was very close to theoretical one of -0.85. However it was also observed at the higher concentration that its layer thickness decreased more abruptly than theoretical expectation and this phenomenon was ascribed to Oosawa type attractive interaction between adjacent latex particles.

• Journal of Adhesion and Interface
• /
• v.11 no.4
• /
• pp.174-180
• /
• 2010

The effect of carbon nanotube surface treatment on the interface and thermal conductivity of carbon nanotube-based poly(methylmethacrylate) (PMMA) composites was investigated. Coagulation and atomic-transfer radical polymerization (ATRP) was applied to modify the surface of multi-wall carbon nano-tube. The composite of ATRP method used carbon nanotube showed the higher transparency and thermal conductivities than that of the coagulation method used. In comparison to the thermal conductivity of pure PMMA, 0.21 W/mK, the ATRP carbon nanotube used PMMA/MWNT composite showed a thermal conductivity of 0.38 W/mK. The interface between carbon nanotube and PMMA was observed by scanning electron microscope and uniform dispersion of carbon nanotube was observed without any void in the PMMA matrix. It may be beneficial to transport the phonon without any scattering and it may result in a higher thermal conductivity.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.160-168
• /
• 2010

An experimental study has been conducted to investigate the effects of forcing amplitude on the tone-excited non-premixed jet flame of the resonance frequency. Visualization techniques are employed using the laser optic systems, which are RMS tomography, PLIF and PIV system. There are three lift-off histories according to the fuel flow rates and forcing amplitudes; the regime I always has the flame base feature like turbulent flame when the flame lift-off, while the flame easily lift-off in the regime II even if a slight forcing amplitude applied. The other is a transient regime and occurs between the regime I and regime II, which has the flame base like the bunsen flame of partial premixed flame. In the regime I and II, the characteristics of the mixing and velocity profile according to the forcing phase were investigated by the acetone PLIF, PIV system. Particular understanding is focused on the distinction of lift-off history in the regime I and II.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.290-296
• /
• 2003

The heteroepitaxial growth of crystalline 3C-SiC on 6H-SiC substrates using high purity silane ($SiH_4$) and prophane ($C_3H^8$) was carried out by thermal chemical vapor deposition, and growth characteristics were investigated in this study. In case that the flow ratio of C/Si and flow rate of $H_2$ were 4.0 and 5.0 slm, respectively, the growth rate of epilayers was about 1.8 $\mu$m/h at growth temperature of $1200^{\circ}C$. The Nomarski surface morphology, X-ray diffraction, Raman spectroscopy, and photoluninescence of grown epilayers were measured to investigate the crystallinity. In this study, the high quality of crystalline 3C-SiC heteropitaxial layers was observed at growth temperature of above $1150^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.8
• /
• pp.708-712
• /
• 2002

The crystallization of amorphous $\alpha$-Fe$_2$O$_3$/$\alpha$-AI$_2$O$_3$(0001) thin films during thermal annealing in air has been studied using real-time synchrotron x-ray scattering. The well aligned (0.02$^{\circ}$/ FWHM) $\alpha$-Fe$_2$O$_3$and Fe$_3$O$_4$interfacial crystallites (50- -thick) coexist on the $\alpha$-AI$_2$O$_3$(0001) in the sputter-grown amorphous films at room temperature. The amorphous precursor is crystallized to the epitaxial $\alpha$-Fe$_2$O$_3$grains in three steps with annealing temperature; i ) the growth of the well aligned $\alpha$-Fe$_2$O$_3$interfacial crystallites, together with the transformation of the Fe$_3$O$_4$crystallites to the $\alpha$-Fe$_2$O$_3$ crystallites, ii ) the growth of the less aligned (3.08$^{\circ}$ FWHM)$\alpha$-Fe$_2$O$_3$grains on the well aligned grains (＞40$0^{\circ}C$), and iii) the nucleation of the other less aligned (1.39$^{\circ}$ FWHM) $\alpha$-Fe$_2$O$_3$grains directly on the $\alpha$-AI$_2$O$_3$substrate (＞$600^{\circ}C$). The effective thickness thinner than 230 may be very useful for enhancing the epitaxial quality of $\alpha$-Fe$_2$O$_3$/AI$_2$O$_3$(0001) thin films.