• Tunnel and Underground Space
• /
• v.20 no.4
• /
• pp.260-266
• /
• 2010

In this study, wish to analyze effect that affect on each tunnel (right and left tunnel) according as proceeding of leading tunnel (right tunnel), following tunnel (left tunnel) and pilot tunnel excavation through behavior of tunnel and surrounding base by model tests. And stress-transfer mechanism that occurs from in-situ loosing area and arching effect by difference of stiffness ratio and overburden heights were verified experimentally. The model tests were carried out by varying the stiffness of reinforced area and overburden height, measured deformation of tunnel and displacement of surrounding base. The model tests followed exactly the real 2-Arch tunnel construction stages.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.4
• /
• pp.41-49
• /
• 1989

Following the previous paper, the results of test are further presented. As partially prestressed concrete members permit cracks under the service state, deflection and crack control of partially prestressed concrete members is more important than that of reinforced or fully prestressed concrete members. By the test results of load-deflection relation, it can be shown that prestressing ratio significantly affects the behavior of partially prestressed concrete beams. Deflection prediction formula of some codes are tried, and test results are compared with various fomulae of crack spacing and crack width.

• Current Research on Agriculture and Life Sciences
• /
• v.15
• /
• pp.123-131
• /
• 1997

The alternation of light transmissivity of covering films used in most greenhouses over years become of concern. Recently, durable films over 0.1mm in thickness which having 3~5 years life time were popularly used in many greenhouses. However, the films have been replaced yearly with new ones because of lowering light transmittance. The replacement caused negative environmental impact as well as cost increasement. This study was conducted to find fundamental data for developing of a cleaning machine for covering films of greenhouses.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.7
• /
• pp.47-56
• /
• 2016

In the case of excavating ground backfilled with soft ground, ground destruction occurs owing to the discharge of groundwater from excavated back ground in spite of earth retaining wall. To minimize this, indoor model test was implemented applying stabilizing pile as a solution for ground destruction. The unreinforced case was compared with the reinforced case and the comparison demonstrated that the ratio of the gap in settlement of the two cases is about three to one, which proves the reinforcement effect (Kim, 2014). This study has carried out the evaluation of appropriate pile spacing ratio, according to the confirmed effect of stabilizing pile. In the evaluation test the case with pile spacing ratio of 0.66 (5 stabilizing piles) was compared with that of 0.76 (3 stabilizing piles), and it has been shown that applying stabilizing pile has effect on ground destruction reduction, but may rather work as load when pile spacing ratio is narrower than a certain interval. So it was found that adjustment for appropriate pile spacing ratio is required at the stage of design. This study has shown that the pile spacing ratio is appropriate at around 0.7~0.8, which reduces ground destruction and does not function as the load of excavated back ground.

• Tunnel and Underground Space
• /
• v.20 no.1
• /
• pp.58-64
• /
• 2010

GLI model was verified to consider the interaction between a ground and a tunnel lining and to rationally reduce the ground load acting on the secondary lining(concrete lining) of a tunnel. In this study, the economy and the construction condition of tunnel concrete linings designed by a conventional frame model at Lot O of OO line were highly enhanced through a field design change using GLI model. For a few safe considerations, not only about 50% saving of reinforcing steel could reduce the material cost but also the wide space between bars could make it easy to pour concrete mix without voids. There was large saving effect of reinforcing steel for poor ground conditions because Terzaghi's load used in the conventional frame model produces too much high loads for those conditions.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.448-455
• /
• 2007

In 1992, the first design standard of quake proof bridge was established. However, most bridge structures which were constructed without considering earthquake in former times need performance of quakeproof property. Quakeproof analysis in current bridges, is based on analysis of load base which just has strength over the load of simple structures but is not checked through simple comparison of strength performance of structures so that we would like to check that ADRS method is reasonable or not using ADRS method(Accleration-Displacement Response Spectrum Method), a analysis method based on displacement of object of performance test. As the result of that, the capacity spectrum method can avoid complex dynamic analysis in analysis based on loads and it efficiently applies to design verification with normal checking for quakeproof performance and aimed performance of new structures. However we can not consider effects of high modes and it has problem that does not consider falling of performance in structures by repeated load.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.1
• /
• pp.85-93
• /
• 2013

In order to make a more reasonable evaluation on the stiffness of the high-strength mortar-filled sleeve bar splices under cyclic loading, we investigated and analyzed the existing experiment data of 106 full-sized reinforcing bar splices with test variables such as compressive strength of mortar, development length of reinforcement and sleeve type, etc. The following were found: 1) If mortar and the reinforcement development length with $f_{g^*}$(L/d) of more than 340 is used, the cast iron sleeve bar splices for SD350 and SD400 will have the stiffness of higher than A class of the AIJ code. 2) If mortar and the reinforcement development length with $f_{g^*}$(L/d) of more than 400 is used, the cast iron sleeve splices and pipe sleeve splices for SD500 will have the stiffness of higher than A class of the AIJ code.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.04a
• /
• pp.529-533
• /
• 1995

안장은 인체하중이 집중되고, 자전거의 충격과 진동이 직접 전달되는 부위로서 주행 안락도를 높이고 buttock의 discomfort를 감소시킬 수 있도록 설계되어야 한다. 본 연구의 목적은 인체곡면을 본뜬 안장형상 설계를 통하여 buttock의 국부적 discomfort를 감소시키고자 하는 것이다. 인간의 앉은자세에 대한 해부학적 고찰을 통해 좌골결절(Ischial Tuberosity)과 치골결합면(Symphyseal Surface)이 안장과 직접 맞닿는 면으로 파악되었으며, 이들 부위에 대한 집중적 개선이 이루어져야 할 것으로 제안되었다. 문헌조사를 통해 의자설계시 고려해야 할 인체치수 및 지침을 파악하였으며, 안장과 의자의 기능비교를 통해 이를 선별적으로 적용하였다. 인체곡면 측정을 위해 Rod Matrix(3cm 간격, 13*20)방법을 이용하여 10명의 buttock contour를 측정하였으며, 측정된 자료를 분석하여 안장의 곡면형상을 결정하였다. General Comfort Rating, Body Part Discomfort 등의 주관적 안락도 평가방법을 통하여 기존 자전거 안장과 본 연구를 통해 개발된 안장을 비교 평가한 결과, 전반적인 안락도의 향상과 좌골결절 및 치골 결합부의 discomfort 감소효과를 가져온 것으로 파악되었다.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.4
• /
• pp.17-26
• /
• 2023

To consider the risk of damage and fracture of P.C strands, the existing post-maintenance system alone has the limitations, hence it is necessary to quantitatively evaluate and predict the deterioration, durability and safety of facilities and establish a reasonable maintenance system considering the asset value of facilities. Therefore, it is worth considering a preventive maintenance plan that allows proactive measures to be taken before a major defect occurs in the temporary anchor. This study devised a preventive over tension method, reviewed its effectiveness through design and field tests, by calculating the resistance factors by performing a reliability-based optimization design. At this time, the over tension anchor method was evaluated using the ratio of the residual tension force after the fracture of P.C strands to the effective tension force before the fracture of P.C strand, followed by the resistance factor calculated by the optimal solution for each random variables using Excel solver and applying it to the limit state equations. As a result of the study, if the over tension ratio is 125% to 130%, the remaining strands showed a high resistance effect even after the fracture of P.C strand. As a result of the optimization design, it was found that it is appropriate to apply the load factor (γ) of 1.25, and the resistance factors of Φ₁, Φ₂, Φ₃ as 0.7, 0.5, 0.6.

• Journal of the KSME
• /
• v.25 no.4
• /
• pp.304-311
• /
• 1985

원자력발전소는 사고시 주변의 인구 및 환경에 미치는 영향의 심각성을 고려하여 가능한 모든 안전조치를 취하여 설계. 건설되도록 하고 있다. 특히 원자로냉각재 계통의 배관이 그러하며 고도의 안전성 및 신뢰성을 확보하기 위하여 지진에 대해서도 구조적인 건전성이 입증되어야 한다. 일반적으로 지진하중에 대한 배관계통의 내진해석에서는 층응답스펙트럼에 의한 모우드 해석 방법이 이용되고 있다. 이 때 내진해석으로 얻어진 응답의 조합에는 신중한 고려가 필요 하다. 즉 배관계통의 특성, 입력지진의 특성, 계산에 고려하는 모우드의 수등을 감안하여 적절한 응답조합이 이루어져야 한다. 본 해설에서는 여러 가지의 응답조합방법과 해석시 고려되는 모 우드의 수를 제한함으로써 발생하는 오차를 보정하기 위한 누락질량효과(missing mass effect)에 대하여 설명하고자 한다. 또 두 가지의 해석모델에 대하여 실제 내진 해석을 수행하여 그 결 과를 비교검토하기로 한다.