• Korean Journal of Agricultural Science
• /
• v.4 no.1
• /
• pp.88-93
• /
• 1977

The following is the result of experiment on consolidation test under various load increment ratios by alternation of standard load increment ratio. The more load increment ratio was, the more settlement was resulted. But expansions were not associated with load increment ratios. Primary consolidation took longer period to complete as load increment ratio was decreased. And under the condition of over-consolidated range, the completion of primary consolidation took longer period as the load was incremented. Under the condition of normal consolidated range, there was no change in time of completing primary consolidation. The coefficient of consolidation was decreased with increment of consolidation load, and the coefficient of consolidation had high values as the load increment ratio was increased. The values of ratio of secondary consolidation was highest near the transition point of consolidation curve.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.1
• /
• pp.71-78
• /
• 2002

In this study, the influence of the presence of discontinuity planes on the load transfer mechanism and the pattern of loosening zone was studied based on the laboratory test. The trap-door and the reaction plates are installed as the bottom plane of the model box. The vertical discontinuity plane is installed in the dry sand. Various overburden heights and locations of discontinuity planes are applied as major factors in this study. The results show that at higher overburden heights over about 1.5 times the excavation width, the ratio of the transferred stress to the insitu stress converges to a certain value even if the overburden height increases further. The results also show that the discontinuity plane gives relatively larger influence on the load transfer mechanism, that produces the unsymmetrical load concentration, when the discontinuity plane locates within the tunnel width. When the discontinuity plane locates outside the tunnel width, the unsymmetrical load concentration is reduced considerably.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.2
• /
• pp.5-12
• /
• 2001

고유기질토의 정규압밀과 과입밀에 대한 압밀특성을 연구하기 위하여 전북지역에서 채취한 2종류의 고유기질토 IS와 YJ를 사용하여 일련의 실내 표준압밀시험과 반복압밀시험을 수행하였다. 전북지역 대표적인 고유기질토의 물리적 특성은 유기물함량이 각각 58%와 72%, 자연함수비 487%와 635%, 초기공극비 7.02와 9.72이었다. 표준압밀시험결과 K, $M_{v}$ , $C_{v}$ 는 압밀하중이 증가함에 따라서 선행하중을 경계로 일반 점토보다 크게 감소하는 특성을 보였다. 또한 2단계, 3단계 반복압밀 시험결과 K, $M_{v}$ 는 압밀하중이 증가함에 따라서 완만하게 감소하였으며 표준압밀시험결과보다는 작게 나타났다. 2단계 반복압밀의 경우 $C_{v}$ 는 정규압밀영역에서 표준압밀시험결과보다 약 10-12배정도 크게 나타났다. $C_{c}$ , $C_{a}$ 는 압밀하중이 증가함에 따라서 각각 선행하중의 약 2.5배, 3배 하중을 정점으로 크게 증감하는 고유기질토 고유의 특성을 나타냈다. 고유기질토의 $C_{c}$ , $C_{a}$ 는 일반 점토보다 압밀압력 의존성이 큰 특성을 나타냈으며 최대값도 각각 2.9-3.8, 0.3-0.4로 일반 점토보다 큰 값을 보였다. 2단계, 3단계 반복압밀시험결과 $C_{c}$ , $C_{a}$ 는 압밀하중이 증가함에 따라서 약간 증가하였다. $C_{a}$ 는 OCR이 증가함에 따라서 감소하였으며 특히 OCR이 1-2 범위에서 감소폭이 크게 나타났다. 고유길토의 제압밀계수는 반복회수 및 하중의 크기 등에 따라서 큰 영향을 받으며 또한 과압밀 크기의 대소는 고유기질토의 $C_{a}$ 에 큰 영향을 미치는 것으로 생각되어 이 분야에 대한 더 많은 연구가 필요하다.

• Bulletin of the Korean Space Science Society
• /
• 2011.04a
• /
• pp.33.1-33.1
• /
• 2011

이 논문에서는 비선형댐퍼를 이용한 광학탑재체 품질개선 방법에 대해 다루었다. 인공위성은 발사 시에 높은 진동하중에 견디어야 하며, 임무 수행 중에는 광학탑재체가 영상을 획득할 수 있도록 지지해주어야 한다. 그러나 인공위성은 자세제어, 데이터 송신, 탑재체 능동냉각을 위한 진동하중 가진 원을 보유하고 있어, 이를 광학탑재체 노출 시 영상품질이 저감되기 쉽다. 이 논문에서는 비선형 댐퍼를 이용해 발사 시에 높은 진동하중에 견디며, 발사 후에는 진동을 절연시켜 영상품질을 개선시키는 방법에 대한 연구를 수행하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.854-858
• /
• 2002

In this study, Fatigue crack growth behavior of the laser welded sheet metal due to a single overload was investigated. From Fatigue crack propagation test, it was observed that the retardation of fatigue crack growth has been more effective in the welded specimen than in the base metal. And if the distance between the welded part and the position of overload is too close the retardation of fatigue crack growth at the welded part has been decreased. From FEM analysis, it was observed the retardation has been more effective compressive residual stress than plastic zone.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.155-167
• /
• 2004

In this paper, the inelastic buckling behavior of the beam under uniform bending was investigated using the energy-based method, which can tackle problems in fourth order eigenvalue. The pattern of residual stress was not available to satisfy the I-sections manufactured in Korea. however; therefore, the well-known polynomial and simplified pattern of residual stress was adopted in this study. The inelastic lateral-distortional buckling behavior of the beam with I-sections manufactured in Korea was investigated. The study was then extended to the inelastic lateral-torsional buckling of the beam by minimizing the out-of-plane web distortion. The inelastic lateral-torsional buckling results obtained in this paper were compared with the prediction of allowable bending stress given in the Korean steel designers' manual (1995). Results showed that the importance of inelastic lateral-distortional buckling did not arise for beams under uniform bending. Likewise, the design method in KSDM (1995) was proven to bo too conservative for intermediate and short spans of beams without intermediate bracing.

• Tunnel and Underground Space
• /
• v.14 no.5
• /
• pp.381-390
• /
• 2004

In this study, scaled model tests were performed to investigate the deformation behaviors around twin tunnels. Eleven types of test models which had respectively different pillar widths, rock types and loading conditions were mode, where the modelling materials were the mixture of sand, plaster and water. The models with shallower pillar width were cracked under lower pressure than the models with thicker pillar width, and they showed the more tunnel convergences and the clear spatting failures. The models of hard rock were cracked under 50% higher pressure than the models of soft rock and they showed the less tunnel convergences. The failure and deformation behaviors of twin tunnels were also dependent on the loading conditions of models. Futhermore, the results of FLAC analysis were qualitatively coincident with the test results.

• Proceeding of KASS Symposium
• /
• 2008.05a
• /
• pp.127-132
• /
• 2008

Recent years, the response characteristics of large space structures have been studied. Then, for the large space structures with large rise-span ratio, it is clarified that the anti-symmetric mode are representatively amplified. That means the static seismic load for general ramen structure is not suitable for the space structure. In this paper, we propose static seismic loads for space structures and its concept. And for the space structures of beam string structures, execute the time history analysis and quasi static analysis and compare the results of them. From the results, we can prove the validity of static seismic load for space structure.

• Geotechnical Engineering
• /
• v.12 no.4
• /
• pp.101-114
• /
• 1996

In this study, the characteristics of bearing capacity and deformation of intermediate soils are investigated through centrifuge tests. The experimental parameters are footing width, initial stress condition of soils and relative loading rate defined relationship of loading rate and permeability of soils. It is examined that loading rate influences on the bearing capacities and deformations. Based on the test results, some problem of existing specification are introduced in the view of related loading rates and load intensities. Especially it is showed that load intensities magnitude rlre reversed in the same settlement ratio(s/B(%)), due to partial drained effect as well as loading rates in undrained con dition based on the excess pore pressure and deformations measured under loading.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.1
• /
• pp.130-137
• /
• 1996

본 연구는 정적 및 동적하중 재하상태에서 배합조건을 달리한 콘크리트의 파괴특성을 조사하고자 3점 휨 실험을 실시하였다. 실험은 물-시멘트비를 일정하게 유지한 상태에서 슬럼프 값을 변화시키는 경우와 슬럼프 값을 일정하게 유지하면서 물-시멘트비를 변화시키는 경우로 구분하여 배합비를 달리한 6가지 배합형태의 무근콘크리트 시편 54개를 제작하였다. 실험결과에 의하여 콘크리트의 파괴에너지(Gf)와 특성길이(lch)를 구한 수 이를 강도특성(f'c, fsp , Ec, ff)과의 상관관계를 규명하고 파괴에너지(Gf)를 이용한 배합설계의 타당성을 검토하였다.