• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.495-504
• /
• 1996

In this paper, series-fed mirostrip array anteenas with coupling-slots are prposed and their operating characteristics are analyzed based on analyzed based on analytical and experimental results. An accurate analysis method for the slot-coupled feed structure is based on using both circuit coupling between anteenas and full-wave analysis which use travling wave mode and non-traveling wave mode on feed line. The basis functions that used for the numerical analysis bas been determined depending upon the accuracy, convergence properties of the solution, and the computation time:The patch uses 3 EB mode, the slot uses 1PWS mode, and feeders use 5 PWS mode. Series-fed array antennas have been designed, built, and tested in a standing-wave configuration. Using the results of the full-wave analysis, the chebyshev array antennas consisting of 8 elements are designed and fabricated changing the amount excited to each array element by adjusting slot length and by the slot position relative to the feeder. Experiment results show that the series-fed array antenna designed by adjusting the slot position relative to the feeder is superior to that designed by slot length.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.30 no.6
• /
• pp.554-560
• /
• 2008

In posterior maxilla, it is difficult to achieve primary stability of implants due to sinus pneumatization, alveolar bone loss, and low bone quality. The accurate and objective primary stability assessment is important for good prognosis of implants. Purpose: The aim of this study was to assess the primary stability of the non-submerged, internal type implants with maxillary sinus augmentation using deproteinized bovine bone mineral by a resonance frequency analyzer, when residual alveolar bone height is under 8mm Materials and methods: A total of 20 implants was placed into 5 grafted maxillary sinuses in 5 patients. Deproteinized bovine bone mineral (Bio-$Oss^{(R)}$) was used as graft material. SS II implants (diameter 4.1mm, and length 11.5mm, SLA suface)) were placed. All of the patients received maxillary sinus graft procedure by 1-step technique. Residual bone height was $1.3{\sim}7.8mm$ (mean 4.4mm) measured by panorama radiography. After implant placement, RFA was measured at 4,8,12,20 weeks. The results were divided into 2 groups; RFA value under 4mm and over 5mm of bone height. It was statistically analyzed. Results: 1. The primary stability of implants was increased with time 2. The RFA value was above 65 ISQ at 12 weeks 3. There was no correlation between RFA and residual alveolar bone height in maxillary sinus augmentation by 1-step technique. Conclusion: 1-step surgical procedure is a feasible option for patients with as little as 4mm residual alveolar bone height, when utilizing non-submerged, internal type implants with xenografts.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.998-1009
• /
• 1999

In this paper, a microstrip aperture-patch antenna and a microstrip ring antenna, which have single microstrip line feeding systems for the circular polarization, are designed, and experimental results are presented at X-band. The microstrip aperture-patch antenna is characterized by its wide operating frequency range, and the microstrip ring antenna is suitable for a basic radiator in the large array antenna due to its small size. Several design parameters for these antennas are considered and analyzed to improve antenna characteristics such as VSWR bandwidth and axial ratio. Initially, the sizes of the aperture and ring radiator are determined on a basis of the cavity model, then shapes of the patch within the aperture and the inner stub of the ring are optimized using Ensemble software. Measurement results show that the aperture-patch antenna has 25% of VSWR bandwidth and 1.2dB of axial ratio at the boresight, and the ring antenna has 6.7% of VSWR bandwidth and 1.6dB of axial ratio at the boresight.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37C no.12
• /
• pp.1296-1302
• /
• 2012

In this research, optimization of a dual-band dipole array was performed using genetic algorithm. A non-uniform, aperture-shared linear array was configured with dipoles which resonate at 4 GHz and 9.5 GHz. The excited current distributions on dipoles were computed considering mutual coupling between dipole elements. The current distributions were also computed using method of moment (MoM). The optimization using genetic algorithm was performed to obtain the low sidelobe levels in two operating frequency band. The PSLs of the optimized array for 4 GHz and 9.5 GHz are -15.7 dB and -17 dB, respectively. Comparison between computed and simulated results are also discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.222-222
• /
• 2007

RF circuit을 구현하는데 있어서 기판의 전기적 특성을 정확하게 아는 것은 원하는 결과를 추출하기 위해 매우 중요하다. 본 연구에서는 현재 사용되고 있는 PI 기판의 전기적인 특성인 유효 유전율과 loss tangent 값을 T-resonator률 이용해 정확하게 측정하고자 했다. T-resonator는 microstrip 구조로 구현 되었으며 conductor material은 Cu를 사용하였다. PI 기판의 두께는 25um, Cu의 두께는 PI 기판의 종류에 따라 12um 와 18um, T-resonator line width는 50um로 구현하였다. 또한 공진 주파수에 따라 stub 길이가 다른 10개의 T-resonator를 제작하였다. PI 기판의 유효 유전율을 구하기 위해 stub 길이의 open-end effect와 T-junction effect를 고려하였으며 수식을 통해 정확한 유효 유전률을 추출하였다. 또한 PI 기판의 loss tangent 추출에 필요한 dielectric loss를 추출하기 위해 unload quality factor를 분석하였다. Unload quality factor는 dielectric loss, conductor loss, radiation loss를 구성되며 conductor loss와 radiation loss를 수식에 의해 구하고 dielectric loss를 추출 하였다. 추출 된 dielectric loss를 통해 각각의 T-resonator의 loss tangent 값을 구하였다. T-resonator를 이용한 PI 기판의 측정은 비교적 복잡한 수식에 의해 이루어지지만 정확한 data를 얻을 수 있고 다른 재료의 전기적 특성을 추출하는데 응용이 가능하다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.8
• /
• pp.1466-1477
• /
• 2016

This paper analyzes the electrical characteristic such as the impedance(Z), inductance(L), and cable resistance($R_p$) according to the change of cable length in order to move the electrical sorting device for distinguishing between AF non-insulated track circuits from the center of railway to outside railway. The simulation is performed to check the voltage difference between the voltage of sender and the voltage of receiver and determine the possibility of the voltage restoration availability in the frequency filter band through the capacitor compensation. It was applied to the results of the simulation to the sorting devices installed in the actual field. It is proved the availability by checking the measured voltage characteristic according to the capacitor compensating change of $10{\mu}F$ and $16{\mu}F$ before, and after the length of cable is increased with 6 meters. Through this, the prevention of breakdown and damage to facilities and the prevention the safety-related accidents of line workers from the train are expected according to moving the sorting devices of AR non-insulated track circuits to outside railway.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.330-331
• /
• 2005

본 논문에서는 카메라폰용 광학중(Optical zooming) 과 자동초점조절장치 (Auto Focusing, AF)에 쓰일 초음파모터를 제작하였다. 초음파모터의제작 및 시뮬레이션은 유한요소해석 프로그램인 ATILA 5.2.1 (Magsoft co.)를 사용하여 디자인설계에 따른 구동특성을 고찰하였고 제작된 초음파모터는 한쪽 면이 없는 사작형의 탄성체를 제작하였으며 탄성체의 양쪽 다리에 각각 압전체를 부착하였다. 또한 압전세라믹의 조성은 $0.9Pb(Zr_{0.51}Ti_{0.49})O_3-0.1Pb(Mn_{1/3}Nb_{1/3}Sb_{1/3})O_3$의 조성으로 설계하였고 시편의 제조는 7-layer로 적층하였다. 제작된 압전세라믹의 치수는 6*2*0.35$mm^3$(길이*폭*두께)로 제작하였다 또한 탄성체의 외형치수는 10*10*2$mm^3$로 제작하였으며 두께를 각각 0.3[mm], 0.5[mm], 0.8[mm]으로 변화시키며 제작하였다. 두께가 0.8[mm]인경우 공진주파수는 60.5[kHz]를 나타내었으며 초음파모터의 압전세라믹에 인가전압이 증가함에 따라 회전속도와 모터에 흐르는 전류는 증가하였다. 인가전압이 40[Vpp] 일 때 회전속도는 206[rpm] 이며 소비전력은 0.3[W]로 제작된 시편은 카메라폰용 광학중 및 자동초점조절장치시스템 분야에 응용이 가능하다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.6
• /
• pp.979-983
• /
• 2008

Planar antennas are very efficient for the use of the out-door data transmission applications due to their low-profile characteristics. But the size of the antenna in UHF band blocks the practical usage. In this paper, a miniaturized planar antenna is investigated for the application of AMR system in UHF band. The designed antenna is fabricated in the form of the microstrip patch on the FR-4 substrate. The miniaturization is achieved by slot-loading on the patch. First, effects of simple slots on the size reduction are analyzed, followed by the design using more complex slots resulting in the reduction ratio of 37.9% in 425.6 MHz and bandwidth of 3.8 MHz. The effort of epoxy coating for the protection is also investigated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.122-127
• /
• 2013

The paper includes the analytic results of pressure fluctuation data from the combustion of an oxidizer-rich preburner applicable to high-performance, closed-cycle liquid rocket engine systems. The combustion experiments went through two different steps of a chamber pressure during single run. Self-excited pressure fluctuations with a frequency of 78 Hz were observed only at the relatively low chamber pressure condition. These pressure fluctuations are regarded as a bulk mode. The intensity of pressure fluctuations by a root-mean-square value is 13.3% normalized by the chamber static pressure and no pressure excitation was observed at the design pressure condition. The bulk mode has an identical phase across the inside of the chamber and reveals the similar characteristics to the Helmholtz resonator.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.6
• /
• pp.21-26
• /
• 2020

In this paper, we investigated the characteristics of SF-MPAA depend on the structures of radiators when they were embroidered for realizing embroidered SF-MPAA. As increasing pitches by decreasing numbers of grids in length-direction and width-direction of the embroidered radiator the antenna gain and resonance frequency were trendingly decreased. However the characteristics of antenna were affected very much by the pitch in width-direction but affected relatively less by the pitch in length-direction. Therefore it was beneficial to decrease number of grids in length-direction to decrease conductor ratio. SLL was affected by the combination of length-direction pitch and width-direction pitch. The conductor ratio of embroidered radiator was determined by the ratio of pitch to embroidered thread thickness. When the ratio was less than 5 the conductor ratio was decreased rapidly. But when the ratio was larger than 5 the conductor ratio was decreased slowly and saturated.