• Journal of Food Hygiene and Safety
• /
• v.34 no.1
• /
• pp.22-29
• /
• 2019

Validamycin A is an aminoglycoside fungicide produced by Streptomyces hygroscopicus that inhibits trehalase. The purpose of this study was to develop a method for detecting validamycin A in agricultural samples to establish MRL values for use in Korea. The validamycin A residues in samples were extracted using methanol/water (50/50, v/v) and purified with a hydrophilic-lipophilic balance (HLB) cartridges. The analyte was quantified and confirmed by liquid chromatograph-tandem mass spectrometer (LC-MS/MS) in positive ion mode using multiple reaction monitoring (MRM). Matrix-matched calibration curves were linear over the calibration ranges (0.005~0.5 ng) into a blank extract with $R^2$ > 0.99. The limits of detection and quantification were 0.005 and 0.01 mg/kg, respectively. For validation validamycin A, recovery studies were carried out three different concentration levels (LOQ, $LOQ{\times}10$, $LOQ{\times}50$, n = 5) with five replicates at each level. The average recovery range was from 72.5~118.3%, with relative standard deviation (RSD) less than 10.3%. All values were consistent with the criteria ranges requested in the Codex guidelines (CAC/GL 40-1993, 2003) and the NIFDS (National Institute of Food and Drug Safety) guideline (2016). Therefore, the proposed analytical method is accurate, effective and sensitive for validamycin A determination in agricultural commodities.

• Culinary science and hospitality research
• /
• v.21 no.6
• /
• pp.280-290
• /
• 2015

This study was carried out to investigate the change of the quality of wild edible plants, Cirsium setidens Nakai, blanched at various conditions. Samples were blanched under blanching conditions of $90^{\circ}C/25min$, $95^{\circ}C/15min$, and $100^{\circ}C/5min$, with salt concentrations of 0%, 1%, 2%, 3%, 4% and 5%. The color, texture (hardness), chlorophyll and total polyphenols were analyzed. The contents of polyphenol and hardness in Cirsium setidens Nakai were found to be decreased in relation to blanching time. With respect to sensory evaluation, the 3% treatment had a higher overall acceptability than other treatments. The optimal blanching condition was found to be $100^{\circ}C/5min$ and 3% salt.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2369-2379
• /
• 2013

A CMOS x-ray line scan sensor which is used in both medical imaging and non-destructive diagnosis is designed. It has a pixel array of 512 columns ${\times}$ 4 rows and a built-in DC-DC converter. The pixel circuit is newly proposed to have three binning modes such as no binning, $2{\times}2$ binning, and $4{\times}4$ binning in order to select one of pixel sizes of $100{\mu}m$, $200{\mu}m$, and $400{\mu}m$. It is designed to output a fully differential image signal which is insensitive to power supply and input common mode noises. The layout size of the designed line scan sensor with a $0.18{\mu}m$ x-ray CMOS image sensor process is $51,304{\mu}m{\times}5,945{\mu}m$.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.18 no.4
• /
• pp.68-80
• /
• 2015

To increase the utilization of the KOrea Multi-Purpose SATellite(KOMPSAT) series imagery being developed pursuant to the national space development program, high quality images with enhanced locational accuracy should be created through standardized post-processing processes. In the present study, using the Value-Added Processing System(VAPS) constructed for the post-processing of KOMPSAT imagery, location correction experiments were conducted using KOMPSAT-2 and -3 imagery from domestic and overseas regions. First, 50 pieces from each of KOMPSAT-2 imagery were selected from South Korean and North Korean regions, and modeling was conducted using GCP Chips. According to the results, the Root Mean Square Errors(RMSE) for South Korea and North Korea were 1.59 pixels and 2.04 pixels, respectively, and the locational accuracy of ortho mosaic imagery using check points were 1.33m(RMSE) and 1.90m(RMSE), respectively. Meanwhile, in the case of overseas regions for which GCP could not be easily obtained, the improvement of locational accuracy could be identified through image corrections using Open Street Map(OSM). The VAPS and reference materials used in the present study are expected to be very useful in constructing a precise image DB for entire global regions.

• The Journal of the Korea Contents Association
• /
• v.16 no.8
• /
• pp.556-567
• /
• 2016

The aim of this study is to make an education satisfaction assessment tool in university. For this, the related study, researchers meeting were conducted and 20 university students were involved in checking items, and then inventory items were completed. The pilot test was conducted at university in Choongnam Province for EFA(Exploratory Factor Analysis by using outcome data. From them, 4 sub-areas and 12 factors were consisted. The 4 sub-areas are education method, education contents, education environment, and education outputs. The education method is composed of appropriateness and fairness of classroom activities, the education contents are composed of systemization of education contents, the diversity and quality of education contents, and the effectiveness of education contents. The education environment is configured as educational facilities and environment, educational supporting service and administrative services. For content validity, items which adapted over 0.90 S-CVI : Standard Content Validity Index. To 48 inventory items obtained proper contents validity and reliability, measurement of suitability of verification was conducted. Cronbach's ${\alpha}$ of reliability test has emerged as highly 0.987. In CFA(Complimentary Factor Analysis), CFGFI, CFL, TLI, RMSEA, NFI indexes show a good value, therefore, this assessment tool for educational satisfaction in university is suitable for measuring tool.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.118-124
• /
• 2017

To investigate and analyze the cause of the failure of the connecting rod bolt and the crank pin bearing bolt of the diesel engine of this study, the following results were obtained through site surveying, the investigation of literature referring to similar failures, testing and inspection of the fracture surface, and the experience of the researchers. The fractured crank pin bearing bolt of the diesel engine is estimated to be damaged later than the connecting rod bolt. From the shape of fracture surface, it is evident that the failed connecting rod bolt is fractured by fatigue failure due to abnormally repeated loads (e.g. loosening of the connecting bolt, etc.), and is not failed by brittle fractures due to the impact load. The surface of the U-nut on the fractured connecting rod bolt has been worsening due to the improper use of lubricant (agent for prevention of thread fixing) and no usage of separating the each connecting rod on each cylinder. Moreover, there is the possibility that those poor surface conditions of the fractured connecting rod bolt have affected the failure of the connecting rod bolt of the main engine. And it could be assumed that the mechanical characteristic and manufacturing process of the failed connecting rod bolt and crank pin bearing bolt, which were made by a domestic company, conform to the design requirements for those bolts.

• Analytical Science and Technology
• /
• v.25 no.6
• /
• pp.364-369
• /
• 2012

Isotianil is a novel fungicide which induces systemic acquired resistance in plants. It has excellent preventive effects as low dosages against rice blast which is one of the most serious diseases in rice. The Maximum Residue Limit (MRL) of Isotianil in republic of korea was set to 0.1 mg/kg in rice, so it is necessary to determine levels of Isotianil residues in agricultural commodities for controlling food safety. Therefore, The purpose of this study was to develop analytical method for the determination of isotiical residues in agricultural commodities using GC-NPD/MSD. Isotianil was extracted with acetonitrile from apple, chinese cabbage, hulled rice, mandarin, pepper, and soybean. The extract was diluted with saline water, and then dichloromethane partition was followed to recover this fungcide from the aqueous phase. A solid phase extraction with Florisil cartridge was additionally employed for final clean up. Isotianil was analyzed and quantitated by GC-NPD and confirmed by GC-MSD. Average recovery of Isotianil ranged from 70.0 to 103.9% in six representative agricultural commodities with relative standard deviations less than 10%, and limit of quantification (LOQ) was 0.05 mg/kg.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.258-258
• /
• 2013

최근 건조 제품의 양질화, 고급화 및 편의화가 요구되어 이를 충족시키기 위한 새로운 건조방법이 계속 개발 되어 왔다. 이러한 방법들 중에서 저온과 진공하에서 건조가 이루어지는 진공 동결 건조는 가장 완벽한 건조 방법으로 최근 실용화 되고 있다. 진공동결건조란 건조의 한 종류로 수분을 함유한 시료를 동결시킨 후 진공펌프를 이용하여 수증기압을 3중점 이하로 낮추어 얼음을 직접 증기로 만드는 승화의 원리에 의해서 얻어진다. 분무진공동결건조의 특징은 (1) 물리적구조의 보존성, (2) 화학적인 안정성, (3) 생물학적인 활동의 보존성, (4) 제품의 높은 복원성 및 재생성이다. 따라서 분무진공동결건조 기술은 크게 진공, 분무, 동결, 건조, 멸균 등과 같은 요소기술의 복합기술이라 할 수 있다. 분말을 제조하기 위해서 진공동결건조 후 분쇄하는 방법을 사용하나 본 방법에서는 정밀화학품 제조를 위해서 분무진공동결건조 방식을 사용한다. 이를 통하여 적당한 크기인 5~10 um의 입경 제조가 가능하고, 공기동력학적인 입경이 기존 방식에 비해 작아서 허파까지의 운반효율이 1.5~2배 우수하다. 화학, 의학 분야에서의 분무동결 건조는 주로 민감한 제품, 즉 생물학적 고유성의 손상 없이 물을 제거하는데 사용되어 영구적으로 저장 가능한 상태로 보관할 수 있으며 물의 첨가로 원상태로 복구할 수 있어서 매우 각광을 받고 있다. 의약용 냉동건조 제품은 항생물질, 박테리아, 혈청, 백신, 검사 약물, 단백질을 포함하는 생물공학 제품들, 세포, 섬유, 화학제품 등이 있으며 주로 vial 또는 ampule 상태로 건조가 이루어진다.본 연구에서는 원료를 $-194^{\circ}C$의 액체질소에 분무시켜 동결된 미립자를 형성한 후 진공 및 저온상태에서얼음의 승화(sublimation)에 기반한 1차 건조와 수증기 탈착(desorption)에 기초한 2차 건조 과정으로 구성된 분무진공동결건조기를 개발하였다. 분무동결 과정의 해석을 통해 2유체식 노즐을 통해 분무된 미세 입경의 액적이 액체 질소 표면까지 도달하는 회수률, 분무 노즐의 위치, 운전 조건 및 용기의 설계의 최적화를 수행하였다. 초기 액적속도, 분무노즐의 높이, 흡입구 추가에 따른 액적 유동 및 회수의 특성을 제시하였으며 이를 통한 분사시스템 고도화 가능성을 제시하였다. 구형의 미세 입자가 적층된 제품의 동결건조 공정의 해석은 흡착승화 모델(sorption sublimation model)을 기반으로 다음과 같은 열전달, 물질전달, 상변화 모델을 고려하여 유도되었다. 분무노즐 및 냉동/진공 배기계 시작품을 개발하여, 표면의 고다공도를 갖춘 입경 3~20 m 정도의 시료를 얻을 수 있으며, 동역학적 입경 5 m 충족함을 확인하였다.

• Korean Journal of Food Science and Technology
• /
• v.46 no.1
• /
• pp.7-12
• /
• 2014

A sensitive and simple analytical method to identify flutianil residues in agricultural commodities was developed and validated using gas chromatography-electron capture detection (GC-ECD) and mass spectrometry (GC-MS). The flutianil residues were extracted with acetonitrile, partitioned with dichloromethane, and then purified using a silica solid-phase extraction (SPE) cartridge. The method was validated using pepper, sweet pepper, mandarin, hulled rice, soybean, and potato spiked with 0.02 or 0.2 mg/kg flutianil. The average recovery of flutianil was 76.5-108.0% with a relative standard deviation of less than 10%. The limit of detection and limit of quantification were 0.004 and 0.02 mg/kg, respectively. The result of recoveries and relative standard deviation were in line with Codex Alimentarius Commission Guidelines (CAC/GL 40). These results show that the method developed in this study is appropriate for flutianil identification and can be used to maintain the safety of agricultural products containing flutianil residues.

• Korean Journal of Food Science and Technology
• /
• v.49 no.1
• /
• pp.85-89
• /
• 2017

This study was conducted to prevent hardened texture in retorted frozen seafoods such as small octopus, squid, and top shell by adding sorbitol; the strength of mechanical hardness and other qualities were measured. The hardness of the 3 kinds of seafood pretreated with 2-4% (w/w) sorbitol solution decreased by 9-36% compared to the control. The hardness of retorted frozen octopus, squid, and top shell treated with sorbitol solution upon freezing significantly decreased to 1670, 1015, and $521g_f/cm^2$ compared to levels in untreated food of 1841, 1291, and $815g_f/cm^2$ (p<0.05), respectively. Yields based on weight in retorted seafood treated with sorbitol were increased by 2-5% compared to untreated samples. Additionally, the overall preference of texture was 0.4 points higher than that of control samples in descriptive sensory evaluation (p<0.05). The tissue softening of pretreated seafood was based on decreased dewatering due to the formation of small ice crystals during freezing as a result of sorbitol treatment.