• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.6
• /
• pp.479-486
• /
• 2021

In this paper, an ultra small phase locked loop (PLL) with a single capacitor loop filter has been proposed by adding a signal sensing circuit (SSC). In order to extremely reduce the size of the PLL, the passive element loop filter, which occupies the largest area, is designed with a very small single capacitor (2pF). The proposed PLL is designed to operate stably by the output of the internal negative feedback loop including the SSC acting as a negative feedback to the output of the single capacitor loop filter of the external negative feedback loop. The SSC that detects the PLL output signal change reduces the excess phase shift of the PLL output frequency by adjusting the capacitance charge of the loop filter. Although the proposed structure has a capacitor that is 1/78 smaller than that of the existing structure, the jitter size differs by about 10%. The PLL is designed using a 1.8V 180nm CMOS process and the Spice simulation results show that it works stably.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.8
• /
• pp.66-75
• /
• 2016

Due to aggressive scaling of device sizes and reduced noise margins, physical defects caused by aging and process variation are continuously increasing. Additionally, with scaling limitation of metal wire and the increasing of communication volume, fault tolerant method in manycore network-on-chip (NoC) has been actively researched. However, there are few researches investigating reliability in NoC with voltage-frequency-island (VFI) regime. In this paper, we propose a table-based routing technique that can communicate, even if link failures occur in the VFI NoC. The output port is alternatively selected between best and the detour routing path in order to improve reliability with minimized hardware cost. Experimental results show that the proposed method achieves full coverage within 1% faulty links. Compared to $d^2$-LBDR that also considers a routing method for searching a detour path in real time, the proposed method, on average, produces 0.8% savings in execution time and 15.9% savings in energy consumption.

• Journal of Food Hygiene and Safety
• /
• v.24 no.1
• /
• pp.63-68
• /
• 2009

The statistics probability approach for microbial risk assessment (MRA) has been recognized as an efficient method because this probability approach, which can be presented the diversity, variability, and uncertainty for the environmental factors of food processing, provide better realistic results than point estimate. This study was conducted to determine of probability statistics for the environmental factors of the pork-cutting processing i.e. the processing time, the pork meat temperature, and processing room temperature etc. As the input parameters for the MRA, triangular distribution and normal distribution were selected as an efficient probability distribution model, these distributions were analyzed by the simulation. The simulation results showed the processing time estimated 53 min as mean (5% - 22 min and 95% - 98 min), pork meat temperature estimated $4.83^{\circ}C$ as mean (5% - $2.25^{\circ}C$ and 95% - $7.12^{\circ}C$, 48.78% exceed $5^{\circ}C$), and processing room temperature estimated $17^{\circ}C$ as mean (5% - $10.92^{\circ}C$ and 95% - $22.56^{\circ}C$, 71.178% exceed $15^{\circ}C$).

• Horticultural Science & Technology
• /
• v.34 no.1
• /
• pp.183-194
• /
• 2016

This experiment was conducted to establish an official determination method to measure fluazinam residue in horticultural crops for import and export using GC-ECD/MS. Fluazinam residue was extracted with acetone from fresh samples of four representative horticultural products, the vegetable crops green pepper and kimchi cabbage, and the fruit crops mandarin and apple. The acetone extract was diluted with saline water and n -hexane partitioning was used to recover fluazinam from the aqueous phase. Florisil column chromatography was additionally employed for final purification of the extract. Fluazinam was separated and quantitated by GC with ECD using a DB-17 capillary column. The horticultural crops were fortified with three different concentrations of fluazinam. Mean recoveries ranged from 82.5% to 99.9% in the four crops. The coefficients of variation were less than 10.0%. The quantitative limit of fluazinam detection was $0.004mg{\cdot}kg^{-1}$ in the four crop samples. GC/MS with selected-ion monitoring was also used to confirm the suspected residue. This analytical method was reproducible and sensitive enough to measure the residue of fluazinam in horticultural commodities for import and export.

• 전기의세계
• /
• v.27 no.5
• /
• pp.33-54
• /
• 1978

(차례) 1.산학협동심포지업 (1)우리나라에서의 연구개발과 산학협동 (2)산학협동과 산업계의 역할 (3)산학협동의 현황과 진로 2.학술회의A (1)전력게통의 계층구조와 협조원리에 관한 연구 (2)2중층괴상회전자 유도전동기의 이론해석 (3)초고주파가열장치에 사용하는 철공진변압기의 해석적 설계 (4)한국전기기시험연구소 대전력단락 시험설비설계 (5)직류전동기제어를 위한 Thyristor Chopper정류회로에 관한 연구 (6)선로의 개폐정보를 포함하는 전력계통의 상태추정 (7)단일신경세포에 대한 ITEM 신호 특성 3.학술회의B (1)MMM-1 Computer System의 설계 및 제작 (2)Adaptive Delta Modulation System의 성능비교 연구 (3)6GHZ FMD마이크로파 무선전송장치의 개발 (4)적선도에 의한 회로망함수의 결정 (5)동맥혈압의 해석과 그의 전기적 유사모델 (6)피부감각의 정보전달 특성에 관하여 (7)선형직접회로의 공정설계 및 그 특성 조성 (8)DH L.D의 전기적포화현상에 관한 이론적 해석 (9)Potocoupler를 이용한 Isolator 4.학술회의C (1)Al-Al$_{2}$O$_{3}$ -Al박막구조의 전기적 특성 (2)이종금속에 샌드위치된 고분자물질의 단락전조 (3)유전체가 일부체워진 직 6면체의 캐비티의 다중모오드 해석 (4)반도체 가스 검지소자의 제조 및 그의 전기적 특성 (5)실리콘 산화공정에 대한 실험적 고찰 (6)진공증착법에 의한 InSb 박막제도에서 열처리효과 (7)(Ba$_{1}$-xBix) Tio$_{3}$ PTC thermistor의 첨가량의 최적건안 (8)금속박막증착시 두께조절 5.특별강연회 (1)일본에 있어서의 절력계통공학연구 (2)Linear Motor의 최근개발동향량도 높았다. valine과 leucine 및 aspartic acid, glycine과 glutamic acid, leucine과 aspartic acid 간에는 고도의 정상관, glycine과 serine, valine과 phenylalanine, threonine과 proline, phenylalanine과 arginine, methionine과 glutamic acid, histidine과 lysine 간에는 유의 정상관, 그리고 isoleucine과 lysine 간에는 유의한 부상관이 있었다. 4. lysine 함량은 단백질 함량과 정산곤, isoleucine 함량은 단빅질 함량과 부상관을 보였으며, alanine, valine, leucine 함량은 지방함량과 각각 유의한 정산관을 보였다. 5. 대두 단백질은 7.5% acrylamide gel 전기영동에 의해 품종에 따라 12～16개의 구성분으로 분리되었으며, 이들중 주구성분들은 상대이동도가 0.06(a), 0.14(b). 0.24(d) 이었고, 구성분 b의 함량이 품종간에 가장 변이가 컸으며, 구성분 b는 그밖의 주요 구성분들의 함량과 부의 상관이 있었고, 구성분 a는 단백질 함량과 정상관이 있었다. 6. 종실단백질 구성분들의 조합 특성 면에서 공시 86품종은 11개 유형군으로 분류되었으며, 우리나라와 일본품종은 미국품종에 비해 단백질구성분 조성이 훨씬 다양하였다. 7. 이동도가 매우 빠른 단백질 구성분 o(Rm 0.77) p(Rm 0.81)를 모두 갖고 있는 품종은 3품종, 모두 갖고 있지 않은 품종은 1품종이었고, 나머지 82품종은 o나 p중 한 구성분을 갖고 있었으며 그 분포율은 30 : 65 이었는데 미국계 품종은 우리나라 품종에 비해 구성분 o를 간고 있는 비율이 현저히 적었다. 8. 대두 종실은 개화후 22일까지 완만히, 그 이후 20～30일간 급속히

• Journal of Food Hygiene and Safety
• /
• v.32 no.4
• /
• pp.298-305
• /
• 2017

Benzovindiflupyr is a new pyrazole carboxamide fungicide that inhibits succinate dehydrogenase of mitochondrial respiratory chain. This study was carried out to develop an analytical method for the determination of benzovindiflupyr residues in agricultural commodities using LC-MS/MS. The benzovindiflupyr residues in samples were extracted by using acetonitrile, partitioned with dichloromethane, and then purified with silica solid phase extraction (SPE) cartridge. Correlation coefficient ($r^2$) of benzovindiflupyr standard solution was 0.99 over the calibration ranges ($0.001{\sim}0.5{\mu}g/mL$). Recovery tests were conducted on 5 representative agricultural commodities (mandarin, green pepper, potato, soybean, and hulled rice) to validate the analytical method. The recoveries ranged from 79.3% to 110.0% and then relative standard deviation (RSD) was less than 9.1%. Also the limit of detection (LOD) and limit of quantification (LOQ) were 0.0005 and 0.005 mg/kg, respectively. The recoveries of interlaboratory validation ranged from 83.4% to 117.3% and the coefficient of variation (CV) was 9.0%. All results were followed with Codex guideline (CAC/GL 40) and Ministry of Food and Safety guideline (MFDS, 2016). The proposed new analytical method proved to be accurate, effective, and sensitive for benzovindiflupyr determination and would be used as an official analytical method.

• Journal of Food Hygiene and Safety
• /
• v.34 no.2
• /
• pp.140-147
• /
• 2019

An analytical method was developed for the determination of quinoxyfen in agricultural products using the QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) method by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The samples were extracted with 1% acetic acid in acetonitrile and water was removed by liquid-liquid partitioning with $MgSO_4$ (anhydrous magnesium sulfate) and sodium acetate. Dispersive solid-phase extraction (d-SPE) cleanup was carried out using $MgSO_4$, PSA (primary secondary amine), $C_{18}$ (octadecyl) and GCB (graphitized carbon black). The analytes were quantified and confirmed by using LC-MS/MS in positive mode with MRM (multiple reaction monitoring). The matrix-matched calibration curves were constructed using six levels ($0.001-0.25{\mu}g/mL$) and the coefficient of determination ($R^2$) was above 0.99. Recovery results at three concentrations (LOQ, 10 LOQ, and 50 LOQ, n=5) were in the range of 73.5-86.7% with RSDs (relative standard deviations) of less than 8.9%. For inter-laboratory validation, the average recovery was 77.2-95.4% and the CV (coefficient of variation) was below 14.5%. All results were consistent with the criteria ranges requested in the Codex guidelines (CAC/GL 40-1993, 2003) and Food Safety Evaluation Department guidelines (2016). The proposed analytical method was accurate, effective and sensitive for quinoxyfen determination in agricultural commodities. This study could be useful for the safe management of quinoxyfen residues in agricultural products.

• Journal of Food Hygiene and Safety
• /
• v.34 no.2
• /
• pp.115-123
• /
• 2019

An analytical method was developed for the determination of fenpropimorph, a morpholine fungicide, in hulled rice, potato, soybean, mandarin and green pepper using QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) sample preparation and LC-MS/MS (liquid chromatography-tandem mass spectrometry). The QuEChERS extraction was performed with acetonitrile followed by addition of anhydrous magnesium sulfate and sodium chloride. After centrifugation, d-SPE (dispersive solid phase extraction) cleanup was conducted using anhydrous magnesium sulfate, primary secondary amine sorbents and graphitized carbon black. The matrix-matched calibration curves were constructed using seven concentration levels, from 0.0025 to 0.25 mg/kg, and their correlation coefficient ($R^2$) of five agricultural products were higher than 0.9899. The limits of detection (LOD) and quantification (LOQ) were 0.001 and 0.0025 mg/kg, respectively, and the limits of quantification for the analytical method were 0.01 mg/kg. Average recoveries spiked at three levels (LOQ, $LOQ{\times}10$, $LOQ{\times}50$, n=5) and were in the range of 90.9~110.5% with associated relative standard deviation values less than 5.7%. As a result of the inter-laboratory validation, the average recoveries between the two laboratories were 88.6~101.4% and the coefficient of variation was also below 15%. All optimized results were satisfied the criteria ranges requested in the Codex guidelines and Food Safety Evaluation Department guidelines. This study could serve as a reference for safety management relative to fenpropimorph residues in imported and domestic agricultural products.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.11
• /
• pp.140-149
• /
• 1996

Cursive characters are written on an economical principle to reduce the motion of a pen in the limit of distinction between characters. That is, the pen is not lifted up to move for writing a next stroke, the pen is not moved at all, or connected two strokes chance their shapes to a similar and simple shape which is easy to be written. For these reasons, strokes and korean alphabets are not only easy to be changed, but also difficult to be splitted. In this paper, we propose a curvature stroke modeling method for splitting and matching by using a structural primitive. A curvature stroke is defined as a substroke which does not change its curvanture. Input strokes handwritten in a cursive style are splitted into a sequence of curvature strokes by segmenting the points which change the direction of rotation, which occur a sudden change of direction, and which occur an excessive rotation Each reference of korean alphabets is handwritten in a printed style and is saved as a sequence of curvature strikes which is generated by splitting process. And merging process is used to generate various sequences of curvature strikes for matching. Here, it is also considered that imaginary strokes can be written or omitted. By using a curvature stroke as a unit of recognition, redundant splitting points in input characters are effectively reduced and exact matching is possible by generating a reference curvature stroke, which consists of the parts of adjacent two korean alphasbets, even when the connecting points between korean alphabets are not splitted. The results showed 83.6% as recognition rate of the first candidate and 0.99sec./character (CPU clock:66MHz) as processing time.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.68-74
• /
• 2011

Cauliflower mushroom ($Sparassis$ $crispa$) is being cultivated as a functional mushroom since the mushroom contains larger amount of ${\beta}$-glucan than other edible or medicinal mushrooms. In this study, as a fundamental study for the cultivation process of cauliflower mushroom, we assayed the mycelial growth and the productivity of the mushroom cultivated on the sawdust-based medium made of larch ($Larix$ $kaempferi$) by 4 kinds of medium densities and 6 kinds of particle sizes. Low densities of sawdust-based media (0.68~0.72 g/$cm^3$) showed high variations in mycelial growth at early stage on sawdust-based medium. The coefficient of variance for the mycelial growth decreased from higher than 40% at the 3rd week to lower than 10% at the 7th week. High density of sawdust-based medium (0.80 g/$cm^3$) showed relatively lower variation in the mycelial growth at early stage with less than 30% of coefficient of variance, the high density of sawdust-based medium was thought to be quite stable compared to the lower densities of sawdust-based medium. From the viewpoint of mushroom productivity especially for the goods (excluding bottom of fruiting body), 0.76 g/$cm^3$ was better than any other densities; the return rates of fruiting body from each medium were 12.2, 13.6, 13.1, and 12.0% for 0.80, 0.76, 0.72, and 0.68 g/$cm^3$, respectively. By the way, it took about 40 days for harvesting from primordium formation with the sawdust-based medium excluded the particles less than 1 mm, while it took about 70 days with the medium including the particles less than 1 mm. The yield from the sawdust-based medium with the particles less than 1 mm was also quite less than any other sawdust-based medium especially for the goods. Therefore, we recommend that the sawdust-based medium with larch for the cultivation of cauliflower mushroom be prepared as 0.76 g/$cm^3$ in medium density with excluding the particles less than 1 mm.