• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.4
• /
• pp.1-11
• /
• 2004

Numerical analyses on the aerodynamic characteristics of a counter rotating axial flow fan were conducted for the development of an axial type in-line duct fan. The counter rotating fan has a front rotor and a rear rotor which are counter rotating each other. Blade design of the counter rotating fan was done by extension of design method for axial flow fan which consists of rotor and stator blades. Through flow analysis was performed using matrix method which is applied for flow fields prediction of compressors or turbines. Aerodynamic characteristics and characteristic curves of the counter rotating fan were analyzed by expansion of the frequency domain panel method with duct modeling. Pressure losses were higher at leading edge and hub region of rotor blades. Characteristic curve of the counter rotating fan was overpredicted without consideration of viscous effect.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.7
• /
• pp.20-28
• /
• 2002

In this paper, the aerodynamic performance prediction of a 30kW counter-rotating (C/R) wind turbine system has been made by using the momentum theory as well as the two-dimensional quasi-steady strip theory with special care on the wake and the post-stall effects. In order to take into account the wake effects in the performance analysis, the wind tunnel test data obtained for a scaled blade are used. Both the axial and rotational inductions behind the auxiliary rotors are determined through the wake model. In addition, the optimum chord and twist distributions along the blades are obtained from the Glauert's optimum actuator disk model considering the Prandtl's tip loss effect. The performance results of the counter-rotating wind turbine system are compared with those of the conventional single rotor system and demonstrated the effectiveness of the counter-rotating wind turbine system.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.299-304
• /
• 2013

초음속 조건에서 Busemann biplane은 충격파의 중첩에 의해 항력 감소가 일어난다. 그러나 받음각이 증가 할 경우, 앞전에서 궁형 충격파가 발생하여 항력이 급격하게 증가한다. 이에 본 연구에서는 busemann biplane에 플랩을 주어 궁형 충격파를 감소시킬 수 있는 flap biplane의 플랩 길이와 각도의 변화에 따른 공력 성능의 변화를 분석하였다. Flap biplane의 공력성능을 기본 biplane형상 및 diamond airfoil과 비교한 결과, 동일한 양력 조건에서 항력은 diamond airfoil에 비해 약 75%정도 감소함을 확인하였다. 그리고 플랩의 길이와 양항비는 선형의 관계가 있음을 확인하였고, 특정한 플랩의 각도에서 최대 양항비가 도출된다는 사실을 확인하였다. 마지막으로 전압력의 감소를 충격파의 강도로 정의하고, 이를 비교한 결과 flap biplane의 전압력 감소가 diamond airfoil에 비해 약 25%정도가 더 작게 나타난 사실로 부터 flap biplane의 소음 감소 효과를 유추할 수 있었다. flap biplane은 초음속 영역에서 항력과 소음의 감소에 효율적인 익형임을 확인하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.6
• /
• pp.483-488
• /
• 2007

The aerodynamic characteristics of FAST(Future Air Speed Transit) combined the body with tandem wing flying over nonplanar ground surface are investigated by using a boundary element method. To validate the present method, results of the present analysis are compared with the experiment and other numerical results. The arrangement of the tandem wing is determined to secure sufficient aero-levitation force and the stability through the analysis of the aerodynamic characteristics of the FAST. The FAST has the maximum lift characteristics when the tandem wing with lower endplate is located at the front side and the rear side of the body. The stability of the FAST can be secured by using the flaperon of the tandem wing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.95-105
• /
• 2018

Increasing cruise speed is an important issue for the development of the next generation rotorcraft. Among several concepts proposed by previous research, the rotorcraft with ducted fan demonstrates its possibility of high-speed flight. In this study, numerical simulations are conducted to investigate the aerodynamic and flow characteristics of multi-ducted fan in forward flight. The aerodynamic efficiency around front ducted fan is determined by interaction between free-stream velocity and the induced velocity. While flow characteristics of rear ducted fan are dominantly influenced by the front ducted fan. Separation in the front ducted fan occurs faster than that of rear ducted fan, and the separation at duct inlet induces an increase of fan thrust. As a result of interaction effect between each ducted fan, relatively aligned inflow enters to the rear ducted fan. Therefore, thrust of the rear fan is decreased steadily before separation, and sudden changes of thrust in fans occur simultaneously. Due to the pressure decrease on lower surface, the normal force of rotorcraft is reduced with forward speed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1170-1179
• /
• 2009

The purpose of this work is to predict the low frequency aero-acoustic noise generated from the horizontal axis wind turbine, NREL Phase VI for the whole operating conditions of various wind speeds using large eddy simulation and Ffowcs-Williams and Hawkings model provided in the commercial code, FLUENT. Because there is no experimental data about wind turbine noise, we first of all compared aerodynamic performance such as shaft torque and power with experimentally measured value. Performance results show a good agreement with experimental data within about 0.8%. As the wind speed increases, the overall sound pressure level and the sound pressure level by the quadrupole and dipole source show a increasing tendency. Also, sound pressure level is proportional to $r^{-2}$ in the near field and $r^{-1}$ in the far field according to the increase of distance from the center of hub of wind turbine. According to 2 times increase of distance, sound pressure level is reduced by about 6dB.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.3
• /
• pp.321-327
• /
• 2019

The purpose of this study is paper is to improve the flow performance and to reduce the aerodynamic noise of air discharge system consisting of a centrifugal fan, ducts and a housing for the clothes dryer. Using computational fluid dynamics and acoustic analogy based on FW-H (Ffowcs-Williams and Hawkings) Eq., air flow field and acoustic fields of the air discharge system are investigated. To optimize aerodynamic performance and aerodynamic noise, the response surface method is employed. The two factors central composite design using the inflow and outflow angles of fan blades is adopted. The devised optimum design shows the reduction of turbulent kinetic energy in the ducts and the housing of the system, and as a result, the improved flow rate and reduce noise is confirmed. Finally, the experment using the proto-type manufactured usign the optimum design shows the increase of flow rate by 4.2 %.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.749-750
• /
• 2008

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.400-403
• /
• 2007

소형 풍력터빈 설계 시 고려해야 할 익형의 선택, 익형의 붙임각 및 Solidity 등이 터빈의 성능에 미치는 영향을 고찰하였다. 한 개의 익형에 대한 공력계수를 이용하여 수학적 모델링을 통하여 최적 붙임각을 예측하여 경향을 파악하였다. 받음각에 따른 익형의 공력특성을 CFD 기법으로 파악한 후 5개의 Blade를 갖는 Turbine의 성능을 익형의 붙임각에 따라 파악하여 최대 성능을 갖는 붙임각을 최종 산출하였다. 익형 선정시 받음각에 대한 양력/항력 곡선을 이동시키는 캠버 익형의 기능보다는 항력 대양력의 비(L/D) 가 최대인 익형을 선정하는 것이 더욱 중요하며, Blade수가 적을수록 Torque의 양은 증가하고 Blade가 6이상이변 효율이 급격히 감소함을 알 수 있다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.2
• /
• pp.134-143
• /
• 2014

A significant degradation in the aerodynamic performance of wind turbine system can occur by ice accretion on the surface of blades operated in cold climate. The ice accretion can result in performance loss, overloading due to delayed stall, excessive vibration associated with mass imbalance, ice shedding, instrumental measurement errors, and, in worst case, wind turbine system shutdown. In this study, the effects of ice accretions on the aerodynamic characteristics of wind turbine blade sections are investigated on the basis of modern CFD method. In addition, the computational results are used to predict the performance of three-dimensional wind turbine blade system through the blade element momentum method. It is shown that the thickness of ice accretion increases from the root to the tip and the effects of icing conditions such as relative wind velocity play significant role in the shape of ice accretion.