• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.159-162
• /
• 2009

Today's construction is more various and more complex. Because of that, a lot of uncertain factors are occurred and they related uncertain construction duration. For management complex architecture project, importance of construction schedule management also increased. In previous studies, one of solutions to overcome those problems is suggested. It was BIM based construction simulation process which focused on construction schedule and construction schedule management. But latest process had limited point which has no duration estimation function. So this paper suggested duration estimation method and developed duration estimation module. Duration estimation module developed with current scheduling tool MS Project and their macro function. However, this module has just developed Reinforced Concrete Structure and has to do more development and research.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.277-284
• /
• 2012

In this study, a heat-transfer performance analysis is carried out for a multi-channel volumetric air receiver for a solar power tower. On the basis of a series of reviews regarding the relevant literature, a calculation process is proposed for the prediction of the wall- and air- temperature distributions of a single channel at given geometric and input conditions. Furthermore, a unique mathematical model of the receiver effectiveness is presented through analysis of the temperature profile. The receiver is made of silicon carbide. A total of 225 square straight channels per module are molded to induce the air flow, and each channel has the dimensions of $2mm(W){\times}2mm(H){\times}0.2mm(t){\times}320mm(L)$. The heat-transfer rate, temperature distribution and effectiveness are presented according to the variation of the channel and module number under uniform irradiation and mass flow rate. The available air outlet temperature applied to the solar power tower should be over $700^{\circ}C$. This numerical model was actually used in the design of a 200 kW-level commercial solar air receiver, and the required number of modules satisfying the thermal performance could be obtained for the specified geometric and input conditions.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.6
• /
• pp.857-870
• /
• 2017

The use of shield TBM is gradually increasing due to the urbanization of social infrastructures. Reliable estimation of advance rate is very important for accurate construction period and cost. For this purpose, it is required to develop the prediction model of advance rate that can consider the ground properties reasonably. Based on the database collected from field, statistical prediction procedure for field penetration index (FPI) was modularized in this study to calculate penetration rate of shield TBM. As output parameter, FPI was selected and various systems were included in this module such as, procedure of eliminating abnormal dataset, preprocessing of dataset and ridge regression with best subset selection. And it was finally validated by using field dataset.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.12
• /
• pp.801-807
• /
• 2016

This paper aims to compare and study the cooling performance of a battery system in accordance with the inlet and outlet geometry of the air passage in an EV. The arrangement and the heat source of the battery module were fixed, and the inlet/outlet area and its geometry were varied with the analysis of the cooling performance. The results of this study provide suggestions for the air flow stream line inside of a battery, the velocity field, and the temperature distributions. It was confirmed that the volume flow rate of air should be over $400m^3/h$, in order to satisfy conditions under $50^{\circ}C$, which is the limit condition for stable operation. It was also revealed that the diffuser outlet geometry can improve the cooling performance of battery system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.357-359
• /
• 2022

The market for eco-friendly food materials by online distribution is rapidly growing due to major environmental pollution such as air, soil, and water quality, and radical changes in living patterns caused by COVID-19. In addition, because of the aging population and the decrease in agricultural-related population due to social structural changes, aquaponics is emerging as a system that can solve problems such as independence of old economic activities, environmental protection, and securing healthy and safe food. This paper aims to design an intelligent plant growth measurement system among intelligent aquaponics production management modules for optimal growth environment derivation and quantitative production prediction by converging various ICT technologies into existing aquaponics systems. In particular, the focus is on designing systems suitable for production sites that do not have high-performance processing resources, and we propose a module configuration plan for production environments and training data and prediction systems.

• Tunnel and Underground Space
• /
• v.24 no.3
• /
• pp.234-242
• /
• 2014

Deep drilling project should be managed systematically and efficiently because it is significantly influenced by various related factors having uncertainty and high risk in terms of economy and effective management. In particular, drilling project involves participants from various sectors including necessary service company and it also needs their collaboration by sharing related information occurring at drilling process in order to secure efficient performance management. We developed 4D (3D + time) information based visualization system for progress management by combining 3D design model and predicted optimized control parameters for each section in geothermal well design. We also applied PDM (precedence diagramming method) to the system in order to setup the effective process model and hooked it up to 3D information based on precedence relation and required time for informatized process network.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.1
• /
• pp.133-141
• /
• 1994

In this paper, experiences obtained during the development of MASS(Noise Analysis of Ship-board using SEA) are described. The results are summarized as follows. (1) The modelling techniques for ship structure and cabins are suggested. (2) Structureborne and airborne noise for a real ship were measured at sea trial and predicted by NASS. The differences between the two values are acceptably small for the cabins located on higher decks, although problems related with modelling of lower decks and evaluation of radiation efficiency were found.

• Journal of Astronomy and Space Sciences
• /
• v.21 no.2
• /
• pp.141-152
• /
• 2004

Optics fabrication process for precision space optical parts includes bound abrasive grinding, loose abrasive lapping and polishing. The traditional bound abrasive grinding with bronze bond cupped diamond wheel leaves the machine marks of about $20{mu}m$ rms in height and the subsurface damage of about 1 ${mu}m$ rms in height to be removed by subsequent loose abrasive lapping. We explored an efficient quantitative control of precision CNC grinding. The machining parameters such as grain size, work-piece rotation speed and feed rate were altered while grinding the work-piece surfaces of 20-100 mm in diameter. The input grinding variables and the resulting surface quality data were used to build grinding prediction models using empirical and multi-variable regression analysis. The effectiveness of such grinding prediction models was then examined by running a series of precision CNC grinding operation with a set of controlled input variables and predicted output surface quality indicators. The experiment achieved the predictability down to ${pm}20$ nm in height and the surface roughness down to 36 nm in height. This study contributed to improvement of the process efficiency reaching directly the polishing and figuring process without the need for the loose abrasive lapping stage.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.263-263
• /
• 2023

블랙아이스는 눈에 쉽게 구분되지 않아 많은 교통사고를 초래하고 있다. 한국교통연구원 교통사고분석시스템에 따르면, 2017년부터 2021년까지 5년간의 서리/결빙으로 인한 교통사고 사망자는 122명, 적설로 인한 교통사고 사망자는 40명으로, 블랙아이스는 적설에 비해 위험성이 높은 것으로 나타난다. 과거의 다양한 연구에서 블랙아이스 생성조건을 기압과 한기 축적등의 조건에서 예측해왔지만, 이러한 기상학적 모델은 봄철 해빙기의 일교차로 인한 눈의 해동과 재냉각과 같은 다양한 기상 조건에서의 블랙아이스 탐지가 어렵다는 한계가 있어 최근에는 이미지 판별과 딥러닝모델(YOLO 등)을 기반으로 한 센서가 제시되고 있다. 그러나, 이러한 방법은 충분한 컴퓨팅 자원이 뒷받침되어야 하며, 블랙아이스 탐지까지 걸리는 속도가 빠르지 못한 편으로, 블랙아이스 초입 구간에서의 제동에 취약하다는 잠재적인 약점을 가지고 있다. 그러므로 본 연구에서는 블랙아이스의 주 원인인 서리나 어는비가 발생하기 위해서 주변 공기가 이슬점 온도 이하, 노면온도와 이슬점이 어는점보다 낮아야 함을 이용, IoT 센서 모듈을 통해 Magnus 방정식으로 계산한 이슬점 온도와 노면 온도를 사용하는 이동식 블랙아이스 추정 장치를 제시한다. 본 장치는 대기압, 온도, 습도로부터 계산된 이슬점 온도와 노면 온도를 통한 서리발생 가능성과 대기 온도, 노면 온도를 통해 어는비의 발생환경 여부를 계산한다. 본 연구 결과를 통해 블랙아이스 추정과 기상정보 생산을 동시에 가능케 하며, 추정 결과를 통합 수집서버에 전송함으로서 운전자에게 전방 블랙아이스 위험 구간을 조기에 전달하는 시스템과 이를 관리하기 위한 인프라를 구축하여 운전 시 결빙 미끄러짐 사고를 저감하고자 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.1
• /
• pp.28-33
• /
• 2016

Batteries are used for main power engine in the fields such as mobiles, electric vehicles and unmanned submarines, for starter and lamp driver in general automotive, for emergency electric source in ship. These days, lead-acid and the lithium ion batteries are increasingly used in the fields of the secondary battery, and the lead-acid battery has a low price and safety comparatively, The lithium ion battery has a high energy density, excellent output characteristics and long life, whereas it has the risk of explosion by reacting with moisture in the air. But Recently, due to the development of waterproof, fireproof, dustproof technology, lithium batteries are widely used, particularly, because their usages are getting wider enough to be used as a power source for hybrid ship and electric propulsion ship, it is necessary to manage more strictly. Hybrid ship has power supply units connected to the packets to produce more than 500kWh large power source, and therefore, A number of the communication modules and wires need to implement the wire inspection and monitor system(WIIMS) that allows monitoring server to transmit detecting voltage, current and temperature data, which is required for the management of the batteries. This paper implements a low price type wireless inspection and monitoring system(WILIMS) of the lithium ion battery for hybrid vessels using BLE wireless communication modules and power line modem( PLM), which have the advantages of low price, no electric lines compared to serial communication inspection systems(SCIS). There are state of charge(SOC), state of health(SOH) in inspection parts of batteries, and proposed system will be able to prevent safety accidents because it allows us to predict life time and make a preventive maintenance by checking them at regular intervals.