• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.794-801
• /
• 2017

When a radial wheel is placed so as to partially overlap a conductive plate and rotated, a lift force is generated on the wheel, a thrust force along the edge, and a lateral force which tends to reduce the overlap region. When several of these wheels are combined, it is possible to realize a system in which the stability of the remaining axes is ensured, except in the traveling direction. To validate the overall characteristics of the multi-wheel system, we propose a transfer system levitated magnetically using radial electrodynamic wheels. The proposed system is floated and propelled by four wheels and arranged in a structure that allows the thrusts generated by the front and rear wheels to offset each other. The dynamic stability of the wheel and the effect of the pole number on the three-axial forces are analyzed by the finite element method. At this time, the thrust and levitation force are strongly coupled, and the only factor affecting them is the wheel rotation speed. Therefore, in order to control these two forces independently, we make use of the fact that the ratio of the thrust to the levitation force is proportional to the velocity and is independent of the size of the gap. The in-plane and out-of-plane motion control of the system is achieved by this control method and compared with the simulation results. The experimental results show that the coupled degrees of freedom can be effectively controlled by the wheel speed alone.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.12
• /
• pp.855-862
• /
• 2012

Caenorhabditis elegans, a free-living nematode mainly found in the soil pore water, roles the critical function in trophic levels, energy flow, and decomposition in soil ecosystem. C. elegans is commonly used species to test soil toxicity. Recently, they are employed broadly as a test organism in nanotoxicology. In this study, a review of the toxicity of nanomaterials for C. elegans was presented based on SCI (E) papers. The nanotoxicity studies using C. elegans have been reported in 20 instances including the mechanism of toxicity. Most studies used K-medium, S-medium, and NGM (Nematode Growth Medium) plate as an exposure medium to test toxicity of nanoparticles. The effects observed include anti aging, phototoxicity, genotoxicity, and dermal effects on C. elegans exposed to nanoparticles. We found that the toxic mechanisms were related with various aspects such as lifespan abnormality, oxidative stress, distribution of particles on inter-organisms, and stress-related gene analysis. C. elegans has advantage to test toxicity of nanoparticles due to various cellular activities, full genome information, and easy observation of transparent body. C. elegans was considered to be a good test species to evaluate the nanotoxicity.

• Membrane Journal
• /
• v.26 no.4
• /
• pp.281-290
• /
• 2016

Thin film composite (TFC) polyamide membranes were prepared on polysulfone (PSF) supports for forward osmosis (FO) applications. To understand the influence of polarity and porosity of support layer on the formation of polyamide structure and the final FO performance, clathochelate metal complex (MC) contained PSF supports were prepared via the phase inversion process from various PSF casting solutions containing 0.1-0.5 wt% of MC in dimethyl formamide (DMF) solvent (18 wt%). A crosslinked aromatic polyamide layer was then fabricated on top of each support to form a TFC membrane. For the porous PSF supports prepared with relatively low concentration casting solutions (12 wt%), the PET film was removed after phase inversion and crosslinked aromatic polyamide layer was then fabricated. The tested sample from PSF (18 wt%)/MC (0.5 wt%) casting solution presented outstanding FO performance, almost similar water flux (9.99 LMH) with lower reverse salt flux (RSF, 0.77 GMH) compared to commercial HTI FO membrane(10.97 LMH of flux and 2.2 GMH of RSF). By addition of MC in casting solution, the thickness of the active layer in FO membranes was reduced, however, the increased RSF value was obtained.

• Journal of Forest and Environmental Science
• /
• v.23 no.1
• /
• pp.57-63
• /
• 2007

Anatomical characteristics of black and white charcoal of Quercus variabilis and Quercus mongolica manufactured by a Korean traditional kiln were investigated by scanning electron microscopy. In both charcoal, the earlywood vessels shrank in tangential direction, whereas the other cells didn't change. However, in the case of latewood vessels, black charcoal did not show tangential direction shrinkage, but white charcoal did. The wood fiber were changed severly in shape due to the excessive shrinkage. Tyloses in early wood vessel were still shown unchanged shape in both charcoals. Cell wall of ray parenchyma was observed and their shapes were severly distorted. Voids between ray parenchyma were observed in white charcoal, which maybe due to high temperature in white charcoal. Moreover, lumen diameters in the uniseriate ray and multiseriate ray were decreased at the high charring temperature. These results showed that the low charcoal yield of the white charcoal compared to the black charcoal was caused by decrease of cell dimensions as well as loss of wood components associated with the carbonization temperature.

• Geophysics and Geophysical Exploration
• /
• v.14 no.4
• /
• pp.324-334
• /
• 2011

Seismic wave velocity change has been monitored due to the accumulation of micro-cracks by uniaxial loads on the rock samples from Seokmo Island with stepwise increase in 5 stages. After the load was applied up to 95% of UCS, P- and S-wave velocities varied in ranges of 0.9 ~ 18.3% and 2.8 ~ 14.8% of fresh rock sample velocities, respectively. Unlike seismic velocity of the dry rock samples that showed overall decreases after the loading, velocity changes of saturated rock samples were much more complicated. These seemed to be due to the mixture of two contradictory mechanisms; i.e. accumulation of micro-crack causes an increase in porosity and a decrease in wave velocity, while saturation causes an increase in wave velocity. Most of tested rocks showed a trend of velocity increase with low axial load and then velocity decrease at later stages. Starting stage of velocity decrease differs from samples to samples. After the failure of rock occurred, noticeable increases of porosity and decreases of wave velocity have been observed. It showed overall trend that the more the quartz contents and the lower the silicate, the higher the Young's modulus.

• Journal of the Korea Concrete Institute
• /
• v.28 no.2
• /
• pp.205-212
• /
• 2016

This research investigates the influence of ground granulated blast furnace slag (GGBFS) composition on the alkali-activated slag cement (AASC). Aluminum oxide ($Al_2O_3$) was added to GGBFS binder between 2% and 16% by weight. The alkaline activators KOH (potassium hydroxide) was used and the water to binder ratio of 0.50. The strength development results indicate that increasing the amount of $Al_2O_3$ enhanced hydration. The 2M KOH + 16% $Al_2O_3$ and 4M KOH + 16% $Al_2O_3$ specimens had the highest strength, with an average of 30.8 MPa and 45.2 MPa, after curing for 28days. The strength at 28days of 2M KOH + 16% $Al_2O_3$ was 46% higher than that of 2M KOH (without $Al_2O_3$). Also, the strength at 28days of 4M KOH + 16% $Al_2O_3$ was 44% higher than that of 4M KOH (without $Al_2O_3$). Increase the $Al_2O_3$ contents of the binder results in the strength development at all curing ages. The incorporation of AASC tended to increases the ultrasonic pulse velocity (UPV) due to the similar effects of strength, but increasing the amount of $Al_2O_3$ adversely decreases the water absorption and porosity. Higher addition of $Al_2O_3$ in the specimens increases the Al/Ca and Al/Si in the hydrated products. SEM and EDX analyses show that the formation of much denser microstructures with $Al_2O_3$ addition.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.6
• /
• pp.602-608
• /
• 2013

The aim of this study is to investigate experimentally the effect of the combination of fine particle cement with high Blaine fineness (FC) and recycled aggregates on the engineering properties and micro structure of high volume blast furnace slag (BS) concrete with 75% BS and 21 MPa. FC manufactured by particle classification at the plant with Blaine fineness of more than $7000cm^2/g$ was used as additional alkali activator for high volume blast furnace slag concrete made with recycled fine and coarse aggregates. FC was replaced by 15, 20 and 25% OPC. Test results showed that the incorporation of FC resulted in an increase in the compressive strength compared to BS concrete without FC by as much as 30% due to accelerated hydration and associated latent hydraulic reaction. It was found that the use of FC and recycled aggregates played an important role in activating BS for high volume BS concrete by offering sufficient alkali.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.317-328
• /
• 2016

This research intends to understand the impact of super-absorbent polymer (SAP) as an internal curing agent in Ultra-High Performance Concrete (UHPC). Two different types of SAPs of acrylic acid (SAP_AA) and acrylic acid-co-acrylamide (SAP_AM) were examined with UHPC formulation. Isothermal calorimetry and x-ray diffraction experiments revealed the impact of polymers with the different chemical bonds on cement hydration. To test its feasibility as a shrinkage reducing admixture for UHPC, a series of experiments including flowability, compressive strength, rapid chloride permeability and autogenous shrinkage profile was performed. While both SAPs showed a reduction in autogenous shrinkage, it has been concluded that the SAP size and chemical form significantly affect the performance as an internal curing agent in UHPC by controlling cement hydration and porosity modification. Between the tested SAPs, SAP_AM which absorbs more water in UHPC than SAP_AA, shows better mechanical and durability performance.

• Korean Journal of Soil Science and Fertilizer
• /
• v.25 no.2
• /
• pp.175-180
• /
• 1992

The occurrence of internal cavity of in red ginseng is one of critical quality criteria. The occurrence of internal cavity mainly due to fresh ginseng character that is determined by growth conditions. Growth conditions and percent occurrence of internal cavity were investigated on various ginseng plantations for 6 years and the relation. ships among them were statistically analysed. In addition, field experiments were carried out seperately for the effect of special factors. 1. Internal cavity in red ginseng mainly occurred on area between central part and cortex part of tap root in red ginseng. It was suppose to be caused by characteristics of fresh ginseng. 2. Soil moisture decreased percent occurrence of internal cavity(PIC) above 27.5 % of PIC and increased below it. 3. The factors of shade structure with high intensity of light condition tend to increase PIC. PIC was decreased below 15.9 % of light transmittance rate and increased above it.

• Journal of Korean Society of Forest Science
• /
• v.106 no.2
• /
• pp.204-212
• /
• 2017

Soil disturbance caused by timber harvesting is widely recognized as a potential threat to forest utilization. The degree and extent of soil disturbance is believed to vary with respect to harvesting methods and logging machines. This study has conducted to assess the degree of soil disturbance associated with ground-based cut-to-length (GC) and cable yarding with whole tree (CW) harvesting methods. Soil disturbance was classified using a visual assessment of harvest unit. The properties of soils in different disturbance levels were also evaluated to understand the influence of timber harvesting on soil structure with soil core sampling method. The deep disturbance and soil compaction were observed in sites by 48% and 23% through harvesting areas for GC and CW logging methods, respectively. The results showed that logging machine and number of machine passage had significant influences on soil bulk density and porosity. Soil disturbance types such as rutted, slash cover, and compact were influenced by equipment travel trends in a GC method.