• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.329-332
• /
• 2008

Recently, land sand is being used more because of the deficiency of river sand. In this paper, in order to manufacture high strength concrete in the range of 70MPa, the effect of sand/aggregate ratio and adding fly-ash. As results, we could come to conclusion that the reduction of sand/aggregate ratio caused the increase of fluidity in the range of $37{\sim}45%$ and the maximum strength was 77MPa obtained at S/a=39%, which could be considered as optimum S/a. Besides, we could also get a conclusion that the larger amount of fly-ash increased the fluidity within 20% of replacement ratio (fly-ash to cement ratio) and the compressive strength at the age of 28days was equal to or larger than that of plane concrete, which represented no replacement by fly-ash, at the same range. from the results, it could be seen that the optimum replacement ratio of fly-ash was in the range of $10{\sim}15%$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.3
• /
• pp.151-158
• /
• 2007

The recent government policy for environment is pursuing for a circular waste control system not only to reduce waste as much as possible but also to vigorously use the already produced waste. Copper slag has a higher fineness modulus and a greater specific gravity than natural aggregate. but when the substitutive ratio of fine aggregate is higher than 30%, material segregation occurs by bleeding. Thus, in this study, the strength and the physical properties were tested for the specimens manufactured by varying the types of admixtures, and the substitutive ratio of copper slag to suppress material segregation occurring due to the bleeding of concrete using copper slag as the substitutive material of fine aggregate and to find the adequate substitutive ratio of copper slag.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.5-15
• /
• 2008

The purpose of this study is to examine the validity of recycled aggregates (RAs) as a substitute for Sand-Mat material for soft ground improvement in the housing site development. To evaluate the possibility of RAs as a substitute for sand mat material, first of all, the criteria and regulations related with the quality of lateral drain layer were collected and checked. Secondly, both of the properties of RAs were compared with the properties of natural sand for the lateral drain layer. The material properties related to coefficient of permeability, pressure at-rest state and so on satisfied most standards. On the basis of the test results, RAs were used to the construction site as lateral drain layer. Accordingly, if the quality of RAs can be managed well, the application of these RAs as lateral drain layer to replace natural sand was highly effective. Also, based on cost analysis of two materials, RAs are proved to be very competitive.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.367-375
• /
• 2009

Recently, more focus is shift to imbalances in aggregate market supply and demand and an exhaustion of natural resources. In this situation, Electric arc furnace oxidizing slag (EAF slag) has high application possibility as aggregate for concrete due to similar property with general aggregate. However, it is inherent the problem which causes pop-out by free-CaO contained in slag In this study, we've got the plan to assure the chemical stability of EAF slag, and then experimentally tested the mechanical performance and durability for the fine aggregate used EAF slag. On this test result, we suggest the application plan. At the result of this study, it shows that EAF slag would reduce the surface defect such as pop-out due to natural aging for the fixed hour and adjustment the grain size of EAF slag. And mechanical performance and durability according to the replacement rate of concrete service, were revealed more than equal or equal compare to general aggregate. Hereafter, quality control must precede not to impede the beauty of concrete surface as assure the safety for aging and processing. And, to establish the environmental resource recycling system for by-products of steel, it should be made development of various application and guideline of quality control for the EAF slag aggregate. Moreover, it must be constantly studied all kind of engineering performance and durability for related to this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.8
• /
• pp.4033-4038
• /
• 2013

Sedimentary rocks from construction waste are discarded through open storage and landfilling, which causes an increase in construction cost and inefficient of execution of works. Some sandstone are selected and utilized as aggregates, but shale is buried as industrial waste. Therefore, in this research, we evaluated weathering properties of shale aggregate that is widely distributed throughout Daegu-Kyeongbuk region and freeze-thaw characteristics of concrete according to the replacement ratio of shale aggregate, in an effort to stabilize aggregate supply-demand in Daegu-Kyeongbuk region and develop alternative aggregates. We used red shale and black shale in the experiment, which were exported from a construction site in Deagu. We verified the usage of shale as a concrete aggregate by comparing andesite, which is broadly used as a thick aggregate for concrete, to hornfels, which is a metamorphic sedimentary rock. As a result of the experiment, we observed no degradation phenomenon for andesite and hornfels. However, a part of country rock containing black shale was found to be exfoliated. Red shale started having cracks in the direction of stratification after 1.5 months of direct exposure, and it broke into smaller pieces after approximately 4 months. After 300 cycles of freeze-thaw process on the concrete manufactured according to the replacement ratio of shale aggregate, the modulus of elasticity was 97% for plain and 95% for hornfels. In the case of RS_100, it was 57% after 210 cycles, and for BS_100, it was 54% after 240 cycles. Therefore, we established that, as the number of repetition increases, the freeze-thaw resistance decreases dramatically.

• Economic and Environmental Geology
• /
• v.54 no.5
• /
• pp.549-560
• /
• 2021

In 2019, at 147 local governments, a total of 872 operations produced aggregates with 414 operations by permission, 458 operations by declaration except the marine operations. The leading aggregate sources were, in descending order of the number of operations, crushed, forest, land, washing, river aggregate. By aggregate type, gravel-only operations were slightly more than sand-only ones. By province, Gyeongsangbuk-do had 149 operations, followed by Gyeonggi-do with 135, Gangwon-do with 113, and Gyeongsangnam-do with 92, Chungcheongbuk-do with 81, and Jeollabuk-do with 70. A review of production by size of operation indicated that about 23,100 thousand m³ (17.6% of the total aggregate) was produced by 17 operations reporting production of more than 1 million m³, about 29,900 thousand m³ was produced by 44 operations reporting production between 500 and <1,000 thousand m³, about 60,000 thousand m³ was produced by 273 operations reporting production between 100 and <200 thousand m³, about 17,000 thousand m³ was produced by 409 operations reporting production between 10 and <100 thousand m³. 129 operations that producted less than 10 thousand m³ accounted for 0.4% of total aggregate produced in Korea in 2019. Operations that produce more than 1 million m³ of aggregate was only from forest and crushed aggregate. The period of permission for aggregate producing based on permission is mostly less than 10 years, and in particular, for river and land aggregates, the permission period is very short, less than 2 years.

• Economic and Environmental Geology
• /
• v.57 no.2
• /
• pp.161-175
• /
• 2024

Aggregate typically refers to sand and gravel formed by the transportation of rocks in rivers or artificially crushed, constituting a core resource in the construction industry. Gyeongsangbuk-do, the largest administrative area in South Korea, produces various sources of gravel, including forest, land (excluding other sources), river, and crushed stone. As of 2022, it has extracted approximately 6.96 million cubic meters of aggregate, with permitted production totaling around 4.07 million cubic meters and reported production of about 2.88 million cubic meters. The aggregate demand in Gyeongsangbuk-do is estimated to be 12.39 million cubic meters according to the estimation method in Ready-Mix Concrete. From the supply perspective, about 120 extraction sites are operational, with most municipalities maintaining an appropriate balance between aggregate demand and supply. However, in some areas, there is inbound and outbound transportation of aggregate to neighboring regions. Regions with significant inbound and outbound aggregate transportation in Gyeongsangbuk-do are areas connected to Daegu Metropolitan City and Pohang City along the Gyeongbu rail line, showing a high correlation with population distribution. Gyeongsangbuk-do faces challenges such as population decline, aging rural areas, and insufficient balanced regional development. Analysis using GIS reveals these trends in gravel demand and supply. Currently in this study, Gyeongsangbuk-do meets its demand for aggregate through the supply of various aggregate sources, maintaining stable aggregate procurement. River and terrestrial aggregates may be sustained as short-term supply strategies due to the difficulty of longterm development. Considering the reliance on raw material supply for selective crushing, it suggests the need for raw material management to maintain stability. Gyeongsangbuk-do highlights quarries in the forest as an important resource for sustainable aggregate supply, advocating for the development of large-scale aggregate quarries as a long-term alternative. These research findings are expected to provide valuable insights for formulating strategies for sustainable management and stable utilization of aggregate resources.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.54-59
• /
• 2020

Coarse aggregate is produced in various ways depending on the location and production method. Currently, the construction industry is in need of a stable supply of coarse aggregate and a way to secure standard quality. The purpose of this study is to examine whether the use of coarse aggregate in 3D printing can help solve this problem. ABS filament was selected for use in 3D printing. CATIA was used for the design of the coarse aggregate, and CUBICON Single Plus was used for the production. Six specimens were produced and cured in water for 28 days. Three of them were made with AE agent, and three were made without it. A compressive strength test confirmed that when the AE agent was used, the compressive strength was greater than the lightweight concrete design criterion specified in the concrete standard specification. This suggests that coarse aggregate produced by a 3D printer may be used for lightweight concrete. A mass production system using this method could help to solve the problems facing the construction industry, such as stable supply and demand for coarse aggregate and securing standard quality.

• Economic and Environmental Geology
• /
• v.54 no.5
• /
• pp.581-594
• /
• 2021

In 2020, about 132 million m³ of aggregate was produced in Korea. Of the total domestic aggregates produced in 2020, about 33.3 % was sand and about 66.7% was gravel. It estimated that of the 132 million m³ of aggregates in Korea in 2020, about 52% was produced by screening crushed aggregate, by 36% by forest aggregate, 3% by land aggregate, 5.6% by sea aggregate and 2.5% by washing each other, and 0.4% by river aggregate. This indicates that screening crushed aggregate and forest aggregate are the main producers of domestic aggregates. Leading producing metropolitan cities were Gyeonggi-do, Gyeongsangnam-do, Chungcheongbuk-do, Gangwon-do, Chungcheongnam-do, Incheon in order decreasing volume, which together accounted for about 72.4% of total product. In 2020, aggregates were produced in 153 cities, about 67% of the 231 cities of Korea, 38 local governments have developed aggregates of more than 1 million m³, and the combined production of the 38 cities accounted for about 65% of national total. This means that the aggregate extraction trend of local governments is becoming larger and more concentrated. In 2020, at 153 local governments, a total of 889 operations produced aggregates with 420 operations by permission, 469 operations by declaration. A review of production by size of operation indicated that about 17 million m³ (12.8% of the total aggregate) was produced by 14 operations reporting production of more than 1 million m³. In about 420 operations, the maximum period of permit is 32 years to at least 2 months. When the remaining period of permit is taken into account, only about 55% of active operations can be developed the aggregate after 2021. In order to maintain the permitted aggregate volume by 2020 level, it will be necessary to obtain an extension permit or find new operation sites for at least 200 or more operations.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.2
• /
• pp.101-108
• /
• 2019

This study is analysis of the utilization as a concrete fine aggregate on CGS, a by-product of Integrated coal gasification combined cycle(IGCC). That is, in KS F 2527 "Concrete aggregate," properties of 1~12times to CGS were evaluated, focusing on quality items corresponding to natural aggregate sand(NS) and melted slag aggregate sand(MS). As a result, the distribution of grain shape, safety and expansion were all satisfied with KS standards by physical properties, but the quality was unstable at 7~12times of water absorption ratio and absolute dry density. The particle size distribution was unstable due to asymmetry distribution of coarse particles, and particles were too thick for 7~12times. The passing ratio of 0.08mm sieve was also out of the KS standard at part factor of 7~12times, but chloride content, clay contents, coal and lignite were all satisfactory. Meanwhile, chemical composition was satisfactory except for $SO_3$ in 1~6times, and content and amount of harmful substances were all within the specified value except for F in 7~12times. As a result of SEM analysis, the surface quality and porosity were 7~12times more than 1~6times, and it was the quality was degraded. Therefore, it is necessary to reduce the quality deviation by using separate measures in order to utilize it as concrete aggregate in the future, and if it is premixed with fine quality aggregate, it will contribute positively to solve aggregate supply shortage and utilize circulation resources.