• Journal of Korean Society of Steel Construction
• /
• v.30 no.1
• /
• pp.1-12
• /
• 2018

A curved member should resist bending and torsional moments simultaneously even though the primary load is usually supposed to be gravitational load. The torsional moment causes complicate stress state and also can result in early yielding of material to reduce member strength. According to analysis results, the strength of a curved member that has 45 degrees of subtended angle could decrease more than 50% compare to straight girder. Nevertheless, there have been very few of researches related with ultimate strength of curved girders. In this study, various kinds of stiffness about bending, pure torsion and warping were considered with a number of models in order to verify the main factor that affects ultimate behavior of curved girder. Lateral and rotational displacement of curved member were introduced as lateral-torsional-vertical behavior and bending-torsional moment interaction curve was derived. Finally, a strength equation for ultimate moment of horizontally curved steel I-girders subjected to equal end moments based on the interaction curves. The equation could take account of the effect of curvature, unbraced length and sectional properties.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.71-81
• /
• 1994

A method is presented for the analysis of curved segmentally erected prestressed concrete box girder bridges including time-dependent effects due to load history, temperature history, creep, shrinkage, aging of concrete and relaxation of prestressing steel. The segments can be either precast or cast-in-place. Thin-walled beam theory and finite element method are combined to develop a curved nonprismatic thin-walled box beam element. The element consists of three nodes and each node has eight displacement degrees of freedom, including transverse distortion and longitudinal warping of the cross section.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.815-818
• /
• 2006

This paper deals with the free, in-plane vibrations of curved members with the translational(radial and tangential directions) and rotational springs at the ends. The governing differential equations for the circular curved member are solved numerically using the corresponding boundary conditions. The lowest three natural frequencies and the corresponding mode shapes are obtained over a range of non-dimensional system parameters: the subtended angle, the slenderness ratio, the translational spring stiffness, and the rotational spring stiffness.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.788-793
• /
• 2004

The main purpose of this paper is to Investigate the free vibrations of circular curved members resting on nonhomogeneous elastic foundations. The governing differential equations derived in a previous paper are used. The governing equations are solved numerically to obtain frequencies. Hinged-hinged end constraint is considered in numerical examples. The lowest three natural frequencies are calculated over a wide range of non-dimensional system parameters: the foundation rested ratio, the foundation parameter, the horizontal rise to span length ratio, the slenderness ratio, and the width ratio of the contact area between the member and the foundation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.35-43
• /
• 2017

The minimum reinforcement ratio is an important design factor to prevent a brittle failure in RC flexural members. A minimum reinforcement ratio is presented by assuming an effective depth of cross-section and moment arm lever in CDC and KHBDC. In this study, it suggests that a rational method for minimum reinforcement ratio is calculated by material model and force equilibrium. As results, a minimum reinforcement ratio using a p-r curve in KHBDC is evaluated about 52~80% of recent design code's value and it induces an economical design. And also, a ductility capacity in case of placing this minimum reinforcement amount is evaluated about 89% of recent design code's value, but ductility in a member is 7 or more, so it has a sufficient ductility capacity. Therefore, it is judged that a minimum reinforcement ratio using p-r curve has a theoretical rationality, safety and economy in a flexural member design.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.4
• /
• pp.26-37
• /
• 2020

This study intends to present a fragility analysis method suitable for concrete cable-stayed bridges by performing an analysis reflecting design criteria and material characteristics from the results of inelastic time-history analysis. In order to obtain the fragility curve of the cable-stayed bridge, the limit state of the main component of the cable-stayed bridge is determined, and the damage state is classified by comparing it with the response value based on inelastic time history analysis. The seismic fragility curve of the cable-stayed bridge was made by obtaining the probability of damage to PGA that the dynamic response of the vulnerable parts to input ground motion would exceed the limit state of each structural member. According to the pylon's fragility curve, the probability of moderate damage at 0.5g is 32% for the longitudinal direction, while 7% for the transversal direction, indicating that the probability of damage in the longitudinal direction is higher in the same PGA than in the transversal direction. The seismic fragility curve of the connections showed a very high probability of damage, meaning that damage to the connections caused by earthquakes is very sensitive compared to damage to the pylon and cables. The cable's seismic fragility curve also showed that the probability of complete damage state after moderate damage state gradually decreased, resulting in less than 30% probability of complete damage at 2.0g.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.1
• /
• pp.35-42
• /
• 2001

본 연구는 변화곡률 수평 곡선보의 면외 자유진동에 관한 연구이다. 뒴과 회전관성을 고려한 변화곡률 수평 곡선보의 자유진동을 지배하는 상미분방정식이 유도되었고, 이 지배미분방정식을 수치해석하여 곡선보의 고유진동수를 산출하였다. 지배미분방정식을 수치적분하기 위하여 Runge-Kutta method를 이용하였고, 고유진동수를 산출하기 위하여 Regula-Falsi method와 결합한 행렬값 탐사법을 이용하였다. 본 연구의 이론적 타당성을 검증하기 위하여 타문헌의 고유진동수와 비교하였고, 실험실 규모의 모형실험을 실시하여 이론값과 실험값의 고유진동수를 비교하였다. 수치해석의 결과로 무차원 재변수들의 변화에 따른 무차원 고유진동수를 제 3모드까지 산출하였고, 그 결과들을 고찰하였다. 본 연구의 결과는 곡선형 교량 등과 같이 곡선부재로 이루어진 구조물의 설계시에 유용하게 이용될 수 있을 것으로 기대된다.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.6
• /
• pp.697-706
• /
• 2006

Tower crane's wall tie is generally used for extending of mast height according to rising of lifting height. In order to get wall tie member force this problem, this study concerning wall tie is based on load data described in manual book of 290HC model. This study made the equation of wall tie member force and computer programming for calculating wall tie member force and then get ${\theta}-P$ curves(angle-wall tie force). After considering the ${\theta}-P$ curves, optimum angle range ($48.4^{\circ}{\sim}77.2^{\circ}$) about wall ties (A), (C) members was obtained. Member force of wall tie (B) was changed from tension to compression or from compression to tension at $74^{\circ}$ in service and $54^{\circ}$ in out of service. When both horizontal force($H_A$) and torsional moment ($M_D$) were varied from (+) to (-), wall tie force(A, B, C) were changed almost symmetrically about ${\theta}$-axis. Because this study was based on wall tie analysis conditions, wall tie members in symmetric and ideal geometry shape used for analizing wall tie of tower crane, it is necessary to have more careful verification in order to apply generally the results of this study.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.5
• /
• pp.77-85
• /
• 2020

In this study, the seismic fragility curve according to the boundary conditions is created for a two-pylon concrete cable-stayed bridge, and the effect of the boundary conditions on the seismic fragility of the target bridge is evaluated. An analysis model for the target bridge is constructed using Midas Civil, and a nonlinear time history analysis is performed by applying the fiber element, concrete and rebar material models. The boundary conditions between the pylon and the stiffened girder are classified into four types: rigid, unconstrained, pot bearing, and seismic isolation bearing, and the seismic fragility curves are created for each boundary condition. The plastic hinge section of the pylon, the connection part, and the cable are selected as weak members, and the earthquake vulnerability curve is created for them. As a result of the analysis, it is found that the seismic isolation bearing model shows the lowest damage probability in the pylon and the connection part, and the seismic fragility of the cable is less affected by the boundary conditions than other members.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.2
• /
• pp.175-188
• /
• 2012

A parametric study for varying the radii of curvature is performed with a curved tub girder bridge having three continuous spans. The bracing forces of top lateral bracings from the results of numerical equations are compared to those of 3-dimensional finite element analyses. New modifying factors applicable in computing the nominal member forces of top lateral bracings were suggested. The numerical equations were derived based on one girder system, and it is shown that the numerical equations exhibit some errors compared with 3D FEA results. The main reason for this phenomenon lies on the number of girders. The twin girder system has an external cross-beam between inner and outer girder. It also has larger lateral stiffness than the single girder system. Finally, the distributions by the torsion, bending, distortion, and lateral loading of the top lateral bracing forces were presented in this paper.