• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.34-36
• /
• 2007

현재 모형선을 이용한 선형성능 검증방법에는 크게 2가지 방법이 있다. 첫째는 예인수조에서 예인전차를 이용하여 정수중에 배를 예인시켜 그에 따른 저항을 시험하는 방법이 있고, 둘째는 회류수조에서 배를 고정하여 물을 회전시켜 모형선의 저항을 측정하는 방법이 있다. 이와 같은 방법은 저속 및 대형선박을 검증하기 위해 계발된 방법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기 어려운 것이 현실이다. 예인전차의 예인속도와 회류수조 물의 유속이 소형 고속어선 및 고속레저선박의 속력에 미치지 못하기 때문이다. 따라서 고속을 요하는 선박의 저항성능 평가를 위해 새로운 방법 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실 해상에서 일반 선박을 이용하여 예인하는 방법을 적용하여 저항시험을 수행하였으며 그에 맞는 시스템을 설계하였다.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.37-39
• /
• 2007

고속 활주형선의 선형시험 ${\cdot}$ 검증을 위하여 설 해상모형시험기법을 정립하였으며, 본 시험법을 이용하여 선미 보조동체 장착 유무에 따른 고속 Stepped Hull 선형의 횡동요 및 저항특성을 비교, 분석하였다.

• Journal of Navigation and Port Research
• /
• v.36 no.3
• /
• pp.157-162
• /
• 2012

A planing craft is designed specifically to achieve comparatively high speed on the surface of the water. The frictional resistance of planing craft can be reduced further by injecting air to the craft's bottom. In this paper, the resistance characteristics of high speed planing crafts with & without air injection at the bottom were compared by sea model-test method. As a result, we conformed that planing craft with air injection has much greater the effect of resistance reduction.

• Journal of Navigation and Port Research
• /
• v.32 no.8
• /
• pp.583-588
• /
• 2008

The planing craft is designed specifically to achieve comparatively high speed on the surface of the water. In general, the stepped hull craft has effect improvement in speed and fuel-efficiency because of the reduction of total resistance by a small wetted surface area without corresponding stepped hull craft. In this paper, the high speed stepped hull crafts with respect to the number of bottom steps were performed to compare the effect of resistance performance using at-sea model-test method. In conclusion, the stepped hull craft with twin-step was proved to be effective to reduce the total resistance.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.12-20
• /
• 1997

A potential-based panel method has been developed to investigate the resistance characteristics of a high speed catamaran advancing on the free surface. Normal dipoles and sources are distributed on the body surface while sources are distributed on the free surface. Linearised free surface conditions are used in the present analysis. To avoid the instabilities due to the velocity difference between inner and outer flow of a high speed catamaran, Kutta condition has been applied at the stern. Model test has been carried out not only to validate the numerical results but to confirm the capabilities of a CWC(Circulating Water Channel). It is believed that we can obtain the qualitatively reasonable results in the CWC. Computed results are compared with those of experiments and Insel's experimental values. Since the Kutta condition is applied at the stern, stable solutions are obtained at the high speed range. The present method, using linearised free surface conditions at the high speed range, seems to be a useful tool in the hull form design of a high speed catamaran.

• Journal of the Korean Society for Railway
• /
• v.12 no.5
• /
• pp.732-737
• /
• 2009

Wind tunnel testing on the real-scale pantograph for high-speed train has been conducted to investigate the aerodynamic characteristic of the pantograph at high-speed. The mid-scale subsonic wind tunnel of Korea Airforce Acamedy with 3.5m width, 2.45m height, and 8.8m length test section has been employed. The test model has been supported above 50cm height from the bottom of test section using vertical strut to eliminate the boundary layer generated from the bottom of the test section. The height of the pantograph has been varied in three cases, in both of the normal running and reverse running modes. The resultant lift forces of the pantograph to catenary system in all the cases have been measured and the relation between the test conditions and the lift forces have been extensively analyzed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.4
• /
• pp.693-702
• /
• 2002

The aim of this study is to develop a 3-dimensional dynamic analysis model, capable of considering the interaction between vehicles and bridges more accurately. The dynamic analysis model is developed with the high-speed train (KTX) and a 2-span continuous prestressed concrete box girder bridge with a double track. The 20-car model is developed using the moving vehicle model for the regular trainset. Three-dimensional frame elements are used for the bridge model. Using the developed models, a dynamic behavior analysis program is coded. The analytical results are compared with the dynamic field test results and found to be valid to yield quite accurate dynamic responses. Based on the results of this study, the hybrid model, made up of the moving vehicle model for the heaviest power car and the moving force model for the other cars, is quite simple and effective without loosing the accuracy that much. Under the coincidence condition of two trains traveling with resonance velocity in the opposite directions, it is necessary to check not only the dynamic responses of the bridge with one-way traffic but those with two- way coincidence.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.759-764
• /
• 2008

The planing craft is designed specifically to achieve comparatively high speed on the surface of the water. Most of planing crafts have installed the spray strip in decreasing of wave impaction and improving motion performance of rolling and pitching et al. It is known to reduce the spray and frictional resistance by the effect of lift and improvement of wave profile in high speed. In this paper, the high speed planing crafts with & without spray strip in bottom were performed to compare the resistance performance by model-test. In conclusion, the high speed planing crafts with spray strip in bottom was proved to effect of the resistance decrement of $3.0{\sim}5.0%$.