• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.173-179
• /
• 2000

Cure characteristics. tensile properties, and dynamic properties were investigated on the carbon black-filled natural rubber compounds, in which three typical vulcanization types conventional vulcanization(Conv), semi-efficient(Semi-EV), and efficient(EV) vulcanizations were used. The effects of vulcanization temperature on both the mechanical property and aging resistance of rubber compounds were also investigated. The Conv cure system showed a slightly slower rate of vulcanization than those of Semi-EV and EV ones. On the other hand, it showed a higher value in the maximum torque of cure curve. Higher tensile moduli were observed in Conv system than those in Semi-EV and EV ones, while lower elongation at break were obtained in Conv one. The tensile strength at break were found to be about the same for three cute systems. Hardness, modulus, and tensile strength decreased with increasing the vulcanization temperature, and the degree of changes in the properties was found to be smaller for EV and Semi-EV systems than that in Conv one. The EV system was found to be superior in thermal-aging resistance to Conv one.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.186-194
• /
• 2011

Natural fiber/natural rubber composites were fabricated by uniformly compounding natural rubber and cellulose- based natural fiber kenaf and then by compression molding. The effect of kenaf fiber content on their vulcanization behavior, hardness, tensile properties, tear strength and static and dynamic properties was investigated. The contents of kenaf fiber in the composites were 0, 5, 10, 15, and 20 phr, compared to natural rubber and additives. The result indicated that various properties of natural rubber depended on the kenaf fiber content. With increasing kenaf fiber content, the torque for vulcanization of natural rubber was increased whereas the vulcanization time was reduced as well. The hardness, tensile modulus and tear strength of kenaf/natural rubber composites were gradually decreased with the fiber content whereas the tensile strength and elongation at break were decreased. Also, with increasing the kenaf fiber content the dynamic property of natural rubber was changed more greatly than the static property. The loss factor, which is closely related with the damping or absorption of the energy given to natural rubber, was proportionally increased with the fiber content.

• Elastomers and Composites
• /
• v.39 no.4
• /
• pp.286-293
• /
• 2004

Ester- and ether-based thermoplastic polyurethanes of different hardness were injection molded at different mold temperatures and effects of mold temperature on the physical properties of TPUs were investigated. Glass transition temperatures of soft segments of TPUs were hardly changed by mold temperatures. The phase separation of soft and hard segments of injection molded TPUs were affected little by mold temperatures. However, crystallinity of hard segments, temperature range of rubbery plateau, and tensile strength of injection molded TPUs decreased with increasing mold temperatures for TPUs of high hardness. However, injection molded TPUs of low hardness showed increases of crystallinity of hard segments, temperature range of rubbery plateau, and tensile strength with increasing mold temperatures. Different physical properties of injection molded TPUs depending on mold temperatures were attributed to different crystallization and physical crosslinking effects of hard segments.

• Elastomers and Composites
• /
• v.34 no.5
• /
• pp.391-398
• /
• 1999

Di-2-ethyl hexyl phthalate (DOP) and di-2-ethyl hexyl adiphate (DOA) were mixed with poly(vlnvl chlorides) [PVC] which have different degrees of polymerization (DP). Tensile strength, elongation, density, abrasion resistance, and hardness of these compounds were measured, High molecular weight PVC(DP 2500) was superior to that of DP 1300 for tensile strength, Hardness. But elongation and abrasion resistance of P1300 systems were better than those of P2500 systems. The densities of both systems were almost same. On the other hand, DOP Plasticized PVC was superior to DOA plasticized one for tensile strength, elongation, hardness. In cases of density, abrasion resistance, and flexual resistance, DOA systems were better than those of DOP systems.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.539-547
• /
• 2002

본 연구는 풋콩 탈협기 개발을 위한 기초연구로서 풋콩 탈협기의 급치를 교환할 수 있고, 급동의 주속도와 송풍팬의 회전속도 및 공기 흡입구의 개구면적을 조절할 수 있는 실험장치를 제작하고, 급치의 종류가 풋콩의 탈협 및 손상에 미치는 영향을 분석하였다. 또한 송풍팬의 회전속도와 흡입 공기구의 개구비 변화 따른 선별 성능을 분석하였다. 그 결과를 요약하면 다음과 같다. 1 급치의 종류에 따른 풋콩의 미 탈협율은 철선 급치가 최대 1.6%, 최소 0.0%,평균 0.7%로서 가장 낮게 나타났고, 그 다음이 경도 60의 고무제 급치로서 최대 2.0%, 최소 0.0% 평균 1.1%, 경도 80의 고무제 급치는 최대 2.5%, 최소 0.0% 평균 1.7% 순으로 높아졌다. 또한 풋콩의 미탈협율은 급동 원주속도가 18m/s에서 55m/s로 증가할수록 감소하였다. 이는 급동의 원주 속도가 증가함에 따라 급치의 선단이 풋콩 꼬투리에 가하는 타격력이 증가하기 때문인 것으로 생각된다. 2. 급치의 종류에 따른 풋콩의 손상율은 경도 80의 고무제 급치는 최대 5.2%, 최소 1.3%, 평균 2.8%로서 가장 낮게 나타났고, 그 다음이 경도 60의 고무제 급치로서 최대 5.7%, 최소 2.4% 평균 3.8%, 철선 급치는 최대 6.3%, 최소 2.6% 평균 4.2% 순으로 높아졌다. 또한 풋콩의 손상율은 급동 원주속도가 증가할수록 풋콩 꼬투리의 손상율은 증가하였다. 이 또한 급등의 원주 속도가 증가함에 따라 급치의 선단이 풋콩 꼬투리에 가하는 타격력이 증가하기 때문인 것으로 생각된다. 3. 공기흡입구의 개구면적을 증가시킬수록 선별율은 높게 나타났으나 개구비가 60%이상에서는 선별율이 크게 차이가 나지 않았으며, 송풍팬의 원주속도를 높일수록 선별율은 높게 나타났다.도 콤바인이 직선구간 및 선회구간을 주행하며 수확작업이 가능함을 알 수 있었다. 그러나 곡선구간에서는 최대오차가 65.5 cm로 매우 크게 나타나, 콤바인을 무인 자율주행으로 수확하기에는 어려움이 있는 것으로 나타났다. 실제 포장은 이론적인 완전한 직선보다는 작은 굴곡이 있는 곡선의 형태가 이루어져 있으므로 주행 오차를 감소하기 위해서는 기계시각을 이용하면 보다 정밀한 조향을 이룰 수 있을 것으로 예상된다. 포장에서 DGPS 신호, 자이로 센서 등을 이용한 콤바인의 무인주행 장치는 무인 수확작업을 위한 가능성을 보여주었고, 일부의 센서의 기능을 개선하면 만족한 성능을 나타낼 수 있을 것으로 판단된다.dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.한 최대의 감자 재배지역을 형성하였다. 제주도는 산지지형과 따뜻한 기온으로 2기작이 가능하고, 감자가공 공장설립과 교통발달에 따른 육지 시장과의 접근이 용이해졌기 때문에 남한에서 2번째로 큰 감자재배지역이 되었다.(요약 및 결론에서 발췌)그람양성균에서 효과적이었으며, 농도별 항균력시험 결과 농도가 증가할수록 비례하여 저해율도 증가함을 알 수 있었다. 첨가농도를 달리하여 미생물의 생육도를 측정한 결과, fraction II磎꼭\ulcorner경우 그람양성균에 대해 500 ppm 이상에서 뚜렷한 증식억제효과를 나타내었다.서 뚜렷한 증식억제효과를 나타내었다.min/+}$계 수컷 이형접합체 형질전환 마우스에 AIN-76A 정제사료만을 투여한 대조군은 1.40$\pm$

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.116-117
• /
• 2019

In this research, Proctor insertion resistance test values and Durometer A type hardness values were compared and analyzed between the setting times of the concrete using CGS for Fine Aggregate, and the results are summarized as follows. 1) The Proctor penetration resistance test value and the hardness value of Durometer A type showed a high correlation in the form of a curve. 2) About surface finish The resolution exceeding the hardness value of the Durometer A type uses about 25 HD, and in the case of termination, about 35 HD, and is considered to be effective for determining the surface finishing work time. The possibility to do is expected.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.181-182
• /
• 2020

This study investigates the feasibility tp estimate the compressive strength at early age in hardened concrete by applying Durometer D type. The result of the experiment showed that the compressive strength reached 5MPa 6 hours, and 55 HD when the hardness was measured with the type D of the Duometer. Through this, it is expected that it will be possible to estimate the compressive strength of the initial age and measure it by the age of 28 when using the Durometer D type in the ready-mixed concrete, which will be applied in practice.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.103-104
• /
• 2021

This study attempted to confirm the possibility of estimating condensation time and initial compressive strength with five types of estimation needles in the existing Durometer D type. In order to determine the surface finishing operation time and develop a method for estimating the initial age compression strength, an estimation needle capable of complexly measuring the estimation time and the initial age compression strength based on the Durometer D type was derived as 1.5, 2.0mm.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.190-191
• /
• 2021

This study is conducted to provide a method to estimate the setting time and early age compressive strength using D type durometer.Test results indicated that the use of D type Durometer attached with modified needle, which was designed to secure improved accuracy in setting and compressive strength, enables to estimate setting time and the compressive strength at early age.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.449-452
• /
• 2009

In order to improve incombustibility of EPDM(Ethylene propylene diene monomer)-based rubber, inorganic materials as $Al(OH)_3$ and $Sb_2O_3$ were added. The mechanical and thermal properties have been measured for vulcanized rubber loaded with different concentrations of $Al(OH)_3$ and $Sb_2O_3$. As inorganic material contents increases from 5phr to 30phr, the specific gravity and hardness increase while elongation at break decreases. This study performed incombustibility test and thermal analysis through TGA(Thermogravimetric Analyzer). As a results, incombustible and thermal properties of EPDM-based rubber were improved as $Al(OH)_3$ and $Sb_2O_3$ contents increase.