• Nuclear Engineering and Technology
• /
• v.18 no.3
• /
• pp.183-193
• /
• 1986

Full scale HDR containment experiment series pointed out that the previous containment analysis models have a number of shortcomings. One of them is on the calculational model of short term (0~2sec) pressure difference. The pressure differences between subcompartments are dependent on the flow rate, fluid density, head loss coefficient, and flow area ratio. It, however, is not known that any of them is largely attributed to the disagreement of pressure difference between the measured and the calculated values. In this study, the head loss coefficients are expressed with another form to improve the analytic model. The pressure and the pressure difference are evaluated by using COMPARE code with new correlation, and the results show better agreements with experimental values for V.42 test, but overestimate the measured values for V, 43 and underestimate for V.44.

• Nuclear Engineering and Technology
• /
• v.16 no.4
• /
• pp.195-201
• /
• 1984

A state-of-the-art mechanistic model has been developed to accurately predict the void fraction in the subcooled boiling region having axial nonuniform heat flux. In this study, the void-dependent drift-flux parameters of the Lahey/Ohkawa model were introduced and the mass flux-dependent condensation coefficient were determined by fitting with the experimental data. This model was tested against several experimental data sets to verify its accuracy. Finally the comparison between the predicted void fraction profiles with this model and the profile-fit model for the hot assembly of Kori-Unit 1, Cycle 1 has been performed. It is conclusive that the results show the good agreement between the measured and predicted void fractions, and the profile-fit model has been found to underestimate the void fraction in the subcooled boiling region.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.12
• /
• pp.529-538
• /
• 2002

Conventional method to reduce the handoff call blocking probability(PBH) in mobile communication system is to reserve a predetermined number of channels only for handoff calls. To determine the number of reserved channels, an optimization problem, which is generally computationally heavily involved, must be solved. In this Paper, we propose a call admission control (CAC) scheme that can be used to reduce the PBH without reserving channels in advance. For this, we define a new measure, gain, which depends on the state of the system upon the arrival of a new call. The proposed CAC decision rule relies on the gain computed when a new call arrives. SRN, an extended stochastic Petri nets, provides compact modeling facilities for system analysis can be calculated performance index by appropriate reward to the model. In this Paper, we develop SRN models which can perform the CAC with gain. The SRN models are 2 level hierarchical models. The upper layer models are the structure state model representing the CAC and channel allocation methods considering QoS with multimedia traffic The lower layer model Is to compute the gain under the state of the upper layer models.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.349-356
• /
• 2020

The heat release rate (HRR) and fire growth rate of fire for the solid combustibles consisting of multi-materials was measured through the ISO 9705 room corner test, and the computational analysis in a closed compartment was performed to simulate a fire using the heat release rate prediction model provided by a Fire Dynamics Simulator (FDS). The method of predicting the heat release rate provided by the FDS was divided into a simple model and a pyrolysis model. Each model was applied and computational analysis was performed under the same conditions. As the solid combustible consisting of multi-materials, a cinema chair composed mostly of PU foam, PP, and steel was selected. The simple model was over-predicted compared to the predicted heat release rate and fire growth rate using the pyrolysis model in a closed compartment.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.5
• /
• pp.49-56
• /
• 2007

This paper deals with grid job allocation and grid resource scheduling to provide a stable and quicker job processing service to grid users. In this paper, we proposed a fuzzy logic-based grid job scheduling model for an effective job scheduling in computational grid environment. The fuzzy logic-based grid job scheduling model measures resource efficiency of all grid resources by a fuzzy logic system based on diverse input parameters like CPU speed and network latency and divides resources into several groups by resource efficiency. And, the model allocates jobs to resources of a group with the highest resource efficiency. For performance evaluation, we implemented the fuzzy logic-based grid job scheduling model on the DEVS modeling and simulation environment and measured reduction rates of turnaround time, job loss, and communication messages in comparison with existing job scheduling models such as the random scheduling model and the MCT(Minimum Completion time) model. Experiment results that the proposed model is useful to improve the QoS of the grid job processing service.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.2
• /
• pp.153-163
• /
• 2010

In this paper a frequency response analysis using Krylov subspace-based model reduction and its design sensitivity analysis with respect to design variables are presented. Since the frequency response and its design sensitivity information are necessary for a gradient-based optimization, problems of high computational cost and resource may occur in the case that frequency response of a large sized finite element model is involved in the optimization iterations. In the suggested method model order reduction of finite element models are used to calculate both frequency response and frequency response sensitivity, therefore one can maximize the speed of numerical computation for the frequency response and its design sensitivity. As numerical examples, a semi-monocoque shell and an array-type $4{\times}4$ MEMS resonator are adopted to show the accuracy and efficiency of the suggested approach in calculating the FRF and its design sensitivity. The frequency response sensitivity through the model reduction shows a great time reduction in numerical computation and a good agreement with that from the initial full finite element model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8753-8759
• /
• 2015

Establishment of analysis procedures and validated performance measurements for generator output is required to maintain stable management of generator output in turbine power generation cycle. We developed turbine expansion model and measurement validation model for the performance calculation of generator using turbine output based on ASME (American Society of Mechanical Engineers) PTC (Performance Test Code). We also developed verification model for uncertain measurement data related to the turbine and generator output. Although the model in previous researches was developed using artificial neural network and kernel regression, the verification model in this paper was based on algorithms through Support Vector Machine (SVM) model to overcome the problems of unmeasured data. The selection procedures of related variables and data window for verification learning was also developed. The model reveals suitability in the estimation procss as the learning error was in the range of about 1%. The learning model can provide validated estimations for corrective performance analysis of turbine cycle output using the predictions of measurement data loss.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.273-273
• /
• 2011

현재 사용되고 있는 플로팅 게이트를 이용한 플래시 메모리 소자는 비례축소에 의해 발생하는 단 채널 효과, 펀치스루 효과 및 소자간 커플링 현상과 같은 문제로 소자의 크기를 줄이는데 한계가 있다. 이러한 문제를 해결하기 위하여 silicon nitride와 같은 절연체를 전자의 트랩층으로 사용하는 charge trap flash (CTF) 메모리 소자에 대한 연구가 활발히 진행되고 있다. CTF 메모리 소자의 전기적 특성에 대한 연구는 활발히 진행 되었지만, 수치 해석 모델을 사용하여 메모리 소자의 전하수송 메커니즘을 분석한 연구는 매우 적다. 본 연구에서는 수치 해석 모델을 적용하여 개발한 시뮬레이터를 사용하여 CTF 메모리 소자의 프로그램 동작 시 전하수송 메커니즘에 대한 연구를 하였다. 시뮬레이터에 사용된 모델은 연속방정식, 포아송 방정식과 Shockley-Read-Hall 재결합 모델을 수치해석적 방법으로 계산하였다. 또한 CTF 소자 프로그램 동작 시 트랩 층으로 주입되는 전자의 양은 Wentzel-Kramers-Brillouin 근사 법을 이용하여 계산하였다. 트랩 층에 트랩 되었던 전자의 방출 모델은 이온화 과정을 사용하였다. 게이트와 트랩 층 사이의 터널링은 Fowler-Nordheim (FN) tunneling 모델, Direct tunneling 모델, Modified FN tunneling 모델을 적용하였다. FN tunneling 만을 적용했을때 보다 세가지 모델을 적용했을 때가 더 실험치와의 오차가 적었다. 그 이유는 시뮬레이션 결과를 통해 인가된 전계에 의해 Bottom Oxide 층의 에너지 밴드 구조가 변화하여 세가지 tunneling 모델의 구역이 발생하는 것을 확인 할 수 있었다. 계산된 결과의 전류-전압 곡선을 통해 CTF 메모리 소자의 프로그램 동작 특성을 관찰하였다. 트랩 층의 전도대역과 트랩 층 내부에 분포하는 전자의 양을 시간에 따라 계산하여 트랩 밀도가 시간이 지남에 따라 일정 값에 수렴하고 많은 전하가 트랩 될 수록 전하 주입이 줄어듬을 관찰 하였다. 이와 같은 시뮬레이션 결과를 통해 CTF 메모리의 트랩층에서 전하의 이동에 대해 더 많이 이해하여 CTF 소자가 가진 문제점 해결에 도움을 줄 것이다.

• Journal of Advanced Navigation Technology
• /
• v.28 no.3
• /
• pp.278-287
• /
• 2024

In this paper, telemetry link budget model for small launch vehicle is proposed, and telemetry link budget simulator is implemented. The proposed link budget model consist of geometry model and propagation loss model. The geometry model is calculation of look angle between ground station and small launch vehicle. The propagation loss model consist of free space loss, polarization loss, and de-pointing loss which are appropriate to the small launch vehicle flight environment. The proposed propagation loss model can be calculate propagation loss without complex calculation of propagation environments. The link budget simulator is implemented in MATLAB. The simulator calculate look angle, free space loss, polarization loss parameter, de-pointing loss and received signal level in ground station by using position of ground station, routing of small launch vehicle, 3-D radiation patterns of antennas.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.5221-5229
• /
• 2013

This study focused on the construction of Korean Evacuation load Model for reflecting Korean Evacuation behaviors. For the purposes, several evacuation experiments are executed according to the ages, and the level and types of disabilities. We accumulated the data on the evacuation velocity and behavior patterns according the ages, and the level and types of disabilities. From these results, we proposed the Korean Evacuation Load Model and compared with several popular evacuation simulation model such SIMULEX. As results of these studies, we found the possibility of construction of Korean Evacuation Simulation System based on the Korean Evacuation Model including the evacuation velocity and human behaviors.