• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.124-129
• /
• 2011

Wood plastic composites (WPCs) are attracting a lot of interest recently. In this study, wood flour/polyethylene (PE) composites panels comprised of a coupling agent and nanoclay were prepared by melt-blending followed by compression molding. Five maleic anhydride grafted polyethylene (MAPE) coupling agents were tested, and the best choice and its optimum content were determined. The mechanical properties of the WPCs were measured by UTM, and the thermal properties were measured by TGA, DMA, DSC, and TMA. Adding just a small amount (1 phr) of organoclay made the tensile and flexural strength and the crystallinity of the WPC somewhat increase and the storage modulus and dimensional stability of the WPC largely increase. SEM images showed that the coupling agent drastically improved wood flour/PE interfacial bonding. Selecting the best coupling agent optimized content and adding a small amount of organoclay resulted in a high performance wood flour/PE composite.

• Journal of the Korean Applied Science and Technology
• /
• v.6 no.1
• /
• pp.31-40
• /
• 1989

Five novel amphoteric surfactants of N-acyloxyethylcarboxybetaine series were synthesized via Schotten-Baumman reaction between five acid chlorides containing 10, 12, 14, 16 and 18 carbon atoms in their N-alkyl groups and dimethylaminoethanol to give the intermediate products, 2-dimethylaminoethylalkanoates(2). Quaternization of these products(2) was permitted to from 2-(acyloxyethyldimethylammonic)- acetates(3), whose structures were identified by elemental analysis, IR spectrophotometry and $^1Hnmr$ spectrometry. The yield of the final products was shown in the range of 77-80% based on the intermediate products. The surface tension of the aqueous solution of (3) was measured, and the critical micelle concentrations (cmc) were shown in the range of $2.1\;{\times}\;10^{-3}\;-\;3.3\;{\times}\;10^{-4}mol/l$, and the surface tension at cmc was 28-36 dyne/cm. Cmc was lowered gradually by the increment of the length of N-alkyl ester containing group. The isoelectric point was shown in the range of 4.44-5.20. It showed a tendency to lean toward the acidic site and its range was broadened as increase of the hydrophobic group length. A linear relationship between log cmc and the number of carbon atoms(N) in the hydrophobic alkyl chain was shown in the relative equation of log cmc=-1.75-0.1N, and the contribution rate of N on the standard free energy change in micellization, ${\bigtriangleup}({\bigtriangleup}G^{\circ}m)/{\bigtriangleup}N$, was calculated as -0.23 RT.

• Elastomers and Composites
• /
• v.40 no.3
• /
• pp.196-203
• /
• 2005

In this work, the engine oil resistant evaluation and breakdown analysis of room temperature vulcanizing silicone adhesives were performed through the surface properties, thermal stabilities, adhesive strength, and morphology measurements. As a result, the permeation of engine oil into adhesive specimens was carried out from surface to center in the specimens. And the oil content in the adhesive specimens was increased and the Si-O-Si bond of the adhesives was decomposed with increasing the aging time. The TGA results indicated that the thermal degradation was mainly occurred at under and surfaces of the specimens. The tensile strength, elongation, and adhesive strength of the adhesives were significantly decreased after the engine oil resistant tests, which could be attributed to the initial lose of adhesive properties resulting from the engine oil absorption and thermal aging. And the failure mode of the adhesive specimens was changed from cohesive failure to interfacial failure.

• Clean Technology
• /
• v.13 no.2
• /
• pp.127-133
• /
• 2007

Celite with enormous pore space inside can hold small molecules and can be well blended with polyethylene (PE) to make a Celite-PE film. Two types of Celite-PE film were prepared, one with Celite surface-treated with surfactant to reduce the hydrophilicity and another with plain Celite. The anti-rust chemical such as dicyclohexylamine, dicyclohexylamine nitrite, or diisopropylamine was allowed to permeate into celite pore in the film, and slowly evaporated to protect the packaged steel material from the rust for a long period of time. The chemical concentration in the different packaging film bags was analyzed by a gas chromatography for a month, and the anti-rust effect on iron labware was compared for a six month period. The Celite film was superior to PE film in anti-rust effect and the long-term anti-rust chemical evaporation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.23-29
• /
• 2001

The effects of Ti-silicide process on the electrical properties of an analog polysilicon capacitor were investigated. To improve the linearity with the applied voltage both electrodes, which are polysilicon in our device, should have almost same material properties. The doping concentrations of both electrodes need to be high and to have the similar levels. Voltage Coefficient of Capacitance (VCC) is one of the properties to represent the linearity of analog capacitor, and it is related with the material and the structure of capacitor. In this study, it was possible to obtain the lower VCC by siliciding the polysilicon areas of capacitor. This is due to the parasitic capacitance at the interfaces between silicide and polysilicons, resulting the decrease of unit capacitance. However, we assumed the creation of positive oxide charge near the lower polysilicon electrode during the silicide process.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.588-595
• /
• 2009

The aim of this study was to increase compatibility of immiscible PLA/PCL blend by using electron beam irradiation in the presence of glycidyl methacrylate (GMA). The blends of PLA/PCL containing GMA were irradiated at doses of 10, 50 and 100 kGy and then the irradiated samples were characterized by observing morphology and rheological properties. Blends irradiated with 50 and 100 kGy showed greatly improved interfacial adhesion between two phases in the morphology. Complex viscosity of PLA/PCL(9/1) blend irradiated at dose of 100 kGy was about 100 times higher than that of pure PLA. We found that the compatibility of immiscible PLA/PCL could be improved by electron beam irradiation in the presence of GMA from the investigation of morphology and rheology.

• Textile Coloration and Finishing
• /
• v.29 no.2
• /
• pp.77-85
• /
• 2017

The interfacial adhesion between fiber and matrix affects the physical properties of fiber reinforced composites. In this study, 3-(Methacryloyloxy)propyltrimethoxy silane(MPS) coupling agent was used to increase the interfacial adhesion between polyketone fiber and epoxy resin. The change of surface chemical composition of polyketone fiber treated with MPS was analyzed using a FTIR-ATR. The interfacial bonding between fiber and resin increased with silane coupling agent largely. Consequently, interfacial shear strength(IFSS) was enhanced with increasing concentration of MPS coupling agent and thus, the physical properties of the composites such as flexural properties and dynamic mechanical properties were changed. Flexural strength and modulus increased when the MPS concentration was higher than 0.5wt%. The dynamic storage modulus of Polyketone/Epoxy composites treated with MPS was higher than that of the untreated one. When the MPS concentration of 3wt%, the highest storage modulus was obtained.

• Journal of the Society of Disaster Information
• /
• v.7 no.1
• /
• pp.43-50
• /
• 2011

The Application of Steel Fiber Shotcrete in tunneling construction has become part of tunneling practice at least since the 1970s because of its high bending and tensile properties. Over the past 3 decades, researcher from all over the world have been significantly developing the associated technologies for improved performance of SFRS. But still it has some major drawbacks in terms of durability, damage of pumping hose, wastage due to rebound concrete, corrosion and it costs high. To overcome this situation researcher has to look for some alternative material. Therefore, this part study deals with the three types of fiber in order to find good alternative for steel fiber. Polyamide and Polypropylene fiber were used in this study with 0.6, 0.5% mixing ratio. To evaluate its fresh and harden properties air content, slump, compressive, split tensile and bending strength were measured. After comparing the results of all three types of fiber reinforced concrete with its different mixing proportion this study propose that polyamide fiber with addition ratio of 0.6 % for field use.

• Journal of Convergence for Information Technology
• /
• v.9 no.7
• /
• pp.94-99
• /
• 2019

Friction stir welding was first reported by TWI(The Welding Institute) in 1991, and this welding method has been rapidly used in various industrial areas such railway, automobile, aerospace and shipbuilding industry. Here, we study core characteristics of friction stir welding (FSW) applied to Al 6005-T6 extruded sheets, which is the typical alloy used for railway car bodies. With the fixed welding speed of 500 mm/min, the rotating tool speed was varied from 600 to 1800 RPM. The results of hardness measurement revealed that the hardness of nugget area is ~70% with respect to the parent material, and for the selected range of rotation speed, no clear dependence was observed and the hardness values close to the parent materials were achieved for the area located 5 mm away from the welding interface. The tension test shows that yield strength and tensile strength were slightly decreased with increasing RPM, with no observed difference for the elongation.

• Applied Chemistry for Engineering
• /
• v.22 no.2
• /
• pp.125-132
• /
• 2011

A unitized regenerative fuel cell (URFC) as a next-generation fuel cell technology was considered in the study. URFC is a mandatory technology for the completion of the hybrid system with the fuel cell and the renewable energy sources, and it can be expected as a new technology for the realization of hydrogen economy society in the $21^{st}$ century. Specifically, the recent research data and results concerning the polymer electrolyte membrane for the URFC technology were summarized in the study. The prime requirements of polymer electrolyte membrane for the URFC applications are high proton conductivity, dimensional stability, mechanical strength, and interfacial stability with the electrode binder. Based on the performance of the polymer electrolyte membrane, the URFC technology combining the systems for the production, storage, utilization of hydrogen can be a new research area in the development of an advanced technology concerning with renewable energy such as fuel cell, solar cell, and wind power.