• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.297-301
• /
• 2012

Microbial fuel cell (MFC) is the major of bio-electrochemical system which can convert biomass spontaneously into electricity through the metabolic activity of the microorganisms. In this study, we used an activated sludge as a microbial inoculum and then investigated the feasibility of using dairy wastewater as a possible substrate for generating electricity in MFC. To examine the performance of MFC as power generator, the characteristics on cell potentials, power density, cyclic voltammetric analysis and sustainable power estimation were evaluated for dairy wastewater. The maximum power density of $40\;mW/m^2$was achieved when the dairy wastewater containing 2650 mg/L COD was used, leading to the removal of 88% of the COD. The results from this study demonstrate the feasibility of using MFC technology to generate electricity while simultaneously treating dairy wastewater effectively.

• Journal of the Korean Chemical Society
• /
• v.55 no.2
• /
• pp.157-162
• /
• 2011

In the present study, we developed a portable GC module for real-time, quantitative determinations of gas mixtures in air sample. Capillary or packed column was coiled together with a heater wire and thermocouple in a small case. Together with the small and light weight sensors and valves as well as the rechargeable carrier gas canister, which permits collection and separation of samples, this system can determine the components of complex mixtures of air contaminants at low concentrations with a duty cycle of 10 min. When measured the various samples with a FID and TCD, the system showed, for a capillary column, a good resolution (R=8.3), high sensitivity, reproducibility, and linear dynamic range greater than three orders of magnitude. These results indicate that the portable GC module is expected to be used for a wide range of applications, particularly for in situ environmental monitoring, chemical processes, and regulation of contaminant emission.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.42-47
• /
• 2002

가. 작업별 시험결과 1) 마늘쪽 분리·선별작업 o 마늘쪽 분리기는 통마늘을 1 또는 2∼3쪽으로 분리하여 1차 선별하고, 마늘쪽 선별기는 분리된 마늘을 3단계로 선별되며 작업성능은 시간당 60접 이상을 분리 및 선별할 수 있다. o 개발된 마늘쪽 분리기와 선별기는 소형 경량이며 취급조작이 편리한 기종하고 작업성능이 높고 손상률이 적어 '01년도에 60대가 농가 보급되었으며 '02년도에는 확대 보급될 전망이다. 2) 파종작업 o 작업성능은 경운기용 파종기 2시간/10a, 승용관리기용 직립파종기는 1시간/10a으로 능률적이었으며 작업정도와 생육상태가 양호하였다. o 지역별 파종작업 체계 -난지형 마늘 파종은 직립파종을 하며 제주, 남해 등은 마늘을 파종한 후 10-11월 줄기가 자랐을 때 무공비닐을 피복하고 줄기를 유인하며, 무안은 유공비닐을 피복하고 구멍에 마늘의 1/2 또는 2/3만 묻히도록 파종하며 별도의 줄기유인 작업은 하지 않는다. 의성지역의 한지형 마늘은 트랙터로 쇄토정지후 보행관리기로 골을 내고 인력으로 마늘을 놓으면 관리기가 다음 골을 내면서 복토하는 체계이다. 3) 마늘 수확작업 -마늘 수확기는 난지형 마늘 수확에는 효과가 적으나, 한지형과 같이 깊게 파종하여 인력으로 뽑기 어려운 재배지역에서는 필요한 기종이며, 토양수분이 많으면 굴취된 마늘과 혼이 진동판에 걸려 작업상태가 불량하므로 마늘과 흙의 이송이 원활토록 진동판 형상 및 적정 진폭 구명이 요구됨 4) 마늘줄기 절단작업 -난지형 마늘은 포장에서 건조후 단기간(1-2주)내에 줄기절단을 해야하므로 기계환가 시급하나 한지형 마늘은 아직도 대부분 줄기를 자르지 않고 묶어서 판매하고 있어 기계화의 시급도는 떨어짐 5) 마늘 선별작업 -마늘선별기는 작업성능이 높고 5등급으로 균일 선별되었으며 손상도 없었으나, 기계가 크고 무거워 이동이 곤란하고 가격이 비싸므로 선별등급을 3∼4단계로 줄이고 소형 농가보급형으로 개량제작이 요구됨. 나. 마늘재배 일관기계화에 의한 노동투하시간과 비용 -종자준비부터 통마늘선별까지의 일관기계화로 투입된 주요작업의 노력은 75∼76%가 절감되고, 재배규모 3ha기준시 비용은 44-53%절감되었음.

• Convergence Security Journal
• /
• v.24 no.2
• /
• pp.55-61
• /
• 2024

With the development of IoT technology, wearable services have also developed rapidly. Wearable devices required for this service are used as sensors and controllers in the form of smart bands. Wearable devices implement very concise SWlogic for possible long-term use and use wireless communication protocols to improve convenience. However, because this wearable device aims to be lightweight, it is more vulnerable to security than terminals used for other information services. Many smart healthcare or smart medical services are passive or do not apply security technology. By exploiting this security environment, attackers can obtain or modify important information through access to wearable devices. In this study, we analyzed the technical operating environment of wearable services and identified authentication information reuse attacks, BIAS attacks, battery drain attacks and firmware attacks on wearable devices. And we analyzed the mechanism of each security threat and confirmed the attack effect. In this study, we presented a response plan to respond to the identified security threats. When developing wearable services, it is expected that safer services can be built if the response plan proposed in this study is considered.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.6
• /
• pp.101-111
• /
• 2015

The modular construction method has been getting more attention followed by global eco-friendly trend as the domestic construction industry has focused more on remodeling and extension work. The modular construction method is an industrialized construction system which is not likely as the existing construction method it manufactures more than 70% modules at the factory then assembling can be completed in a short amount of time on site. The modular construction method has various strengths; shortening of construction period by on-site work decrease, weight pressure reduction by usage of light steel frames and cost saving by repetitive manufacturing. However, it is currently not expanded due to the existing commercialized construction method. Therefore, this research is in order to help the related authorities make decisions to select the construction method and motivate expansion of modular construction method which can be utilized effectively in the extension works. The intention of this research is to stress differentiation from other construction methods in construction period, construction expenses, labor and forces by comparing and analyzing actual cases, to inform competitiveness of modular construction method by concrete effect analysis and to support adoption of the modular construction method into the domestic industry.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2010.06a
• /
• pp.183-183
• /
• 2010

위치기반서비스(Location Based Service)는 갈수록 고도화 되어 가고 있다. 특히 최근의 대형 포털을 중심으로 지오웹 서비스가 활성화 되어 있고 이를 스마트폰과 같은 개인용 이용기기를 통해 연속적으로 제공하려는 경향이 뚜렷하다. 이와 같은 시점에서 정부와 민간에서 구축 중이거나 보유 중인 전국적 규모의 데이터 간 상호 연동과 융합을 도모하려는 시도 또한 불가결하다. 이는 고도화된 LBS를 위하여 반드시 필요한 과정이기 때문이다. 이에 따라 몇 가지 주요한 전국 데이터를 대상으로 상호 연동과 융합을 위한 기술개발을 시도하였다. 우선 도로명주소기본도와 수치지형도 간 POI의 연계를 위한 연구를 수행하고 있다. 이 연구에서는 두도면 내의 POI를 대상으로 다양한 매칭과 이에 기반 한 의사결정 방법론을 이용하여 자동으로 상호 인식 및 연계가 될 수 있도록 하고 있다. 다음으로 지적도와 수치지형도 간의 객체 매칭에 관한 연구이다. 수치지형도와 지적도의 불부합으로 인하여 그 동안 지적도를 수치지형도에 맞춘 형태의 편집지적도를 지속적으로 생산하여 왔고 앞으로도 그럴 것이다. 문제는 여기에 필요한 많은 예산이다. 만일 수치지형도와 지적도를 자동으로 매칭하여 편집지적도를 자동으로 생산할 수 있게 된다면 많은 예산 절감과 함께 편집지적도의 현시성을 확보할 수 있게 될 것이다. 다음으로 항공사진과 도로망도의 매칭이다. 현재 주요 포털에서 제공하고 있는 항공사진 기반의 도로망도는 기복변위와 같은 문제로 인하여 시각적으로 많은 위치오차를 보이고 있다. 만일 항공사진의 도로영역을 자동으로 추출하여 벡터 도로망도와 매칭을 할 수 있다면 보다 시각적으로 안정된 항공사진 상의 도로망도를 제공할 수 있게 되고 나아가 이는 차량이나 보행자 네비게이션에 매우 요긴하게 이용될 수 있을 것이다. 다음으로 서로 LOD가 다른 도로망도의 매칭 문제이다. 많은 기관에서 독자적으로 생산한 도로망도는 LOD의 상이에 기인한 문제가 많아 서로 연계 활용되지 않는다. 이를 자동으로 매칭하여 서로 연계할 수 있다면 두 도로망도가 보유하고 있는 속성정보를 공동으로 이용할 수 있는 이익을 얻게 된다. 다음으로 지도 일반화 기술이다. 지도일반화는 지적도내 수치지형도와 같은 대규모 데이터를 스마트폰과 같은 저용량 사양의 기기에 서비스 할 때 불가결한 기술이다. 지도상 객체들의 기하학적 정보 손실을 최소화하면서 메모리 측면에서 경량의 지도를 자동으로 만들어 낸다면 이는 매우 요긴하게 이용될 것이다. 마지막으로 보행자 네트워크의 생성기술이다. 보행자 네트워크는 그 상세함과 정보용량에 있어서 차량용 네트워크에 견줄 수 없다. 이를 현행의 차량용 네트워크와 같이 수동으로 생성하는 데에는 경제적으로나 시간적으로 막대한 투자가 필요하다. 따라서 이를 기존의 공간정보들을 활용하여 자동으로 생성해 낼 수 있다면 그 파급효과는 매우 크리라 판단된다. 본 발표에서는 위와 같은 주제에 관하여 그간의 연구 성과를 개략적으로 소개해본다.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.6
• /
• pp.190-197
• /
• 2012

The purpose of this study was to evaluate thermal environment and heat budget of light thin layer green roof through an experiment in order to quantify its heat budget. Two concrete model boxes($1.2m(W){\times}1.2m(D){\times}1.0m(H)$) were constructed: One experiment box with Zoysia japonica planted on substrate depth of 10cm and one control box without any plant. Between June 6th and 7th, 2012, outside climatic conditions(air temperature, relative humidity, wind direction, wind speed), evapotranspiration, surface and ceiling temperature, heat flux, and heat budget of the boxes were measured. Daily maximum temperature of those two days was $29.4^{\circ}C$ and $30^{\circ}C$, and daily evapotranspiration was $2,686.1g/m^2$ and $3,312.8g/m^2$, respectively. It was found that evapotranspiration increased as the quantity of solar radiation increased. A surface and ceiling temperature of those two boxes was compared when outside air temperature was the greatest. and control box showed a greater temperature in both cases. Thus it was found that green roof was effective in reducing temperature. As results of heat budget analysis, heat budget of a green roof showed a greater proportion of net radiation and latent heat while heat budget of the control box showed a greater proportion of sensible heat and conduction heat. The significance of this study was to analyze heat budget of green roof temperature reduction. As substrate depth and types, species and seasonal changes may have influences on temperature reduction of green roof, further study is necessary.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.4 s.77
• /
• pp.499-509
• /
• 2005

The excessive wind-induced motion of tall buildings most frequently result from vortex-shedding-induced across-wind oscillations. This form of excitation is most pronounced for relatively flexible, lightweight, and lightly damped high-rise buildings with constant cross-sections. This paper discusses the aerodynamic means ofmitigating the across-wind vortex shedding induced in such situations. Openings are added in both the drag and lift directions in the buildings to provide pressure equalization. Theytend to reduce the effectiveness of across-wind forces by reducing their magnitudes and disrupting their spatial correlation. The effects of buildings with several geometries of openings on aerodynamic excitations and displacement responses have been studied for high-rise buildings with square cross-sections and an aspect ratio of 8:1 in a wind tunnel. High-frequency force balance testshave been carried out at the Kumoh National University of Technology using rigid models with 24 kinds of opening shapes. The measured model's aerodynamic excitations and displacement were compared withthose of a square cylinder with no openings to estimate the effectiveness of openings for wind-induced oscillations. From these results, theopening shape, size, and location of buildings to reduce wind-induced vortex shedding and responses were pointed out.

• Journal of the Korean Society of Radiology
• /
• v.7 no.6
• /
• pp.403-408
• /
• 2013

This study made a tentative estimation of the shielding rate of barium compound by thickness through monte carlo simulation to apply medical radiation shielding products that can replace existing lead. Barium sulfate($BaSO_4$) was used for the shielding material, and thickness of the shielding material specimen was simulated from 0.1 mm to 5 mm by applying $15{\times}15cm^2$ of specimen area, $4.5g/cm^3$ of density of barium sulfate, and $11.34g/cm^3$ density of lead. Entered source was simulated with 10kVp Step in consecutive X-ray energy spectrum(40 kVp ~ 120 kVp). Absorption probability in 40 kVp ~ 60 kVp showed same shielding rate with lead in 3 mm ~ 5 mm of thickness, but it was identified that under 2 mm, the shielding rate was a bit lower than the existing lead shielding material. Also, the shielding rate in 70 kVp ~ 120 kVp energy band showed similar performance as the existing lead shielding material, but it was tentatively estimated as fairly low shielding rate below 0.5 mm. This study estimated the shielding rate of barium compound as the thickness function of x-ray energy band for medical radiation through monte carlo simulation, and made comparative analysis with existing lead. Also, this study intended to verify application validity of the x-ray shielding material for medical radiation of pure barium sulfate. As a result, it was estimated that the shielding effect was 95% higher than the existing lead 1.5 mm in at least 2 mm thickness of barium compound in medical radiation energy band 70 kVp ~ 120 kVp, and this result is considered valid to be provided as a base data in weight lightening production of radiation shielding product for medical radiation.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.8
• /
• pp.870-876
• /
• 2005

The multiple regression models which have two factors(population and commercial area) have been used to forecast the water demand in the future. But, the coefficient of population had a negative value because proper regional classification wasn't performed, and it is not reasonable because the population must be a positive factor. So, the regional classification was performed by principal component and cluster analysis to solve the problem. 6 regional characters were transformed into 4 principal components, and the areas were divided into two groups according to cluster analysis which had 4 principal components. The new regression models were made by each group, and the problem was solved. And, the future water demands were estimated by three scenarios(Active, moderate, and passive one). The increase of water demand ore $89.034\;m^3/day$ in active plat $49,077\;m^3/day$ in moderate plan, and $19,996\;m^3/day$ in passive plan. The water supply ability as scenarios is enough in water treatment plant, however, 2 reservoirs among 4 reservoirs don't have enough retention time in all scenarios.